SonyメーカーVPL-PX35の使用説明書/サービス説明書
ページ先へ移動 of 34
DATA PROJECTOR VPL-PX35 DATA PROJECTOR VPL-PX40 DATA PROJECTOR VPL-FX51 PROTOCOL MANUAL 1st Edition (Revised 3).
VPL-PX35/PX40/FX51 ! W ARNING This manual is intended f or qualified ser vice personnel only . T o reduce the risk of electr ic shock, fire or injury , do not perf or m any ser vicing other than that contained in the operating instructions unless you are qualified to do so.
1 VPL-PX35/PX40/FX51 Table of Contents 1. Introduction .............................................................................................. 1 2. RS-232C 2-1. Communication Specifications ......................................................
2 VPL-PX35/PX40/FX51 Appendix A. Setup Method For VPL-PX35 and PX40 A-1. Command ..................................................................................................... 18 A-1-1. Setting ..................................................
1 VPL-PX35/PX40/FX51 EVEN Parity.....Total number of “1”s from D0 to D7 is an even number. D4 D5 D6 D7 (MSB) (LSB) (EVEN) BIT PARITY STOP BIT START D3 D2 D1 D0 1. Introduction This protocol manual describes the basic configuration and basic operations of various commands used for projector.
2 VPL-PX35/PX40/FX51 2-2. Command Block Format The code from B0 to B7 as described below are transmitted. START CODE : 0 x A9 B0 B1 B2 B4 B3 DATA ITEM NUMBER ACK / NAK ITEM NUMBER SET / GET ACK DUMMY .
3 VPL-PX35/PX40/FX51 2-3. Block Format START CODE B0 B1 B2 B4 B3 DATA ITEM NUMBER SET / GET CHECK SUM END CODE B5 B6 B7 START CODE B0 B1 B2 B4 B3 DUMMY DATA ACK / NAK ACK CHECK SUM END CODE B5 B6 B7 S.
4 VPL-PX35/PX40/FX51 2-5. Communication Procedure 2-5-1. Outline of Communication All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the command block format. Communication is started by the issue of a command at CONTROLLER and ended when the return Data is sent to CONTROLLER after DEVICE receives the command.
5 VPL-PX35/PX40/FX51 2-6. Communication Rules . When sending a command from CONTROLLER, the return Data from PROJECTOR should be received first before sending the next command. Even if the next command is sent before receiving the return Data, since PROJECTOR will not be able to receive that command, it does not return a response to CONTROLLER.
6 VPL-PX35/PX40/FX51 3. NETWORK 3-1. Introduction This section describes the specifications, performance and operations of the network service that is going to be installed in the target projector.
7 VPL-PX35/PX40/FX51 3-1-2. Remote Control The remote control service is provided that can control the target equipment from remote location via network. The SDCP protocol that serves to acquire the basic information such as equipment name and serial numbers is installed in this projector.
8 VPL-PX35/PX40/FX51 3-2. SDAP Protocol This section describes the SDAP packet structure. Fig.1 Packet structure 1) Header The header consists of ID (16 bit), version (8 bit) and category (8 bits). Fig. 2 Header ID It is fixed to “ DA ” . Version This indicates the version number of protocol.
9 VPL-PX35/PX40/FX51 3-3. SDCP Protocol This section describes the packet structure of version 2. Fig. 1 Packet structure 3-3-1. Format 3-3-1-1. Header The header consists of Version (8 bits) and Category (8 bits). Fig. 2 Header structure Version This indicates the version number of protocol.
10 VPL-PX35/PX40/FX51 3-3-1-3. Command This section describes the format of the request command and the response command. (1) Request This section describes the format of the request command that is issued from the host PC to the projector.
11 VPL-PX35/PX40/FX51 00h Item No. n Set Data (n byte) Request Item No. Data Length Data OK (01h) Item No. 0 3-3-1-4. SET Request The SET request is used to set a new value in the specified item. Details of the request and the response are described below.
12 VPL-PX35/PX40/FX51 3-3-2. Items Category Contents SET GET 00**h Used to control and to change the various setups. OO 01**h Used to acquire the status. O 03**h Used to reset memory. O 17**h Sircs (15 bit category) O 19**h Sircs (20 bit category) O 80**h Used to acquire equipment information.
13 VPL-PX35/PX40/FX51 3-3-2-3. Network Information Acquisition (90**h) Used to acquire the network setup information. Lower bytes Contents SET GET 00h MAC Address O 01h IP Address O 02h Subnet Mask O .
14 VPL-PX35/PX40/FX51 3-3-3. Error Code The error code list is shown below with a detailed description of each. Category Error Error Code Item Error (01**h) Invalid Item 01h Invalid Item Request 02h I.
15 VPL-PX35/PX40/FX51 3-3-3-1. Item Error This error occurs when the Item No. of a request is illegal or its Data is illegal. The conditions for occur- rence of the respective errors are shown below. Invalid Item An unsupported Item No. is specified. Example 1: The unsupported category 0xA ** is specified.
16 VPL-PX35/PX40/FX51 3-3-3-3. Request Error This error occurs when Header or Command is illegal. The conditions of occurrence of the respective errors are shown below. Invalid Version The version of the Header is other than 2. n When another version is supported, an error occurs in all versions other than the supported version.
17 VPL-PX35/PX40/FX51 3-3-3-5. Comm Error This is an error in communication with the main control microprocessor of the display. Timeout Reception Data is not returned after Data is sent. Check Sum Error A check sum error occurred in the main control microprocessor of the display.
18 VPL-PX35/PX40/FX51 Appendix A. Setup Method For VPL-PX35 and PX40 Establishing the network setup such as IP address can be implemented from the PC browser, and the information such as installation location can be viewed on the PC browser. A-1. Command A-1-1.
19 VPL-PX35/PX40/FX51 A-1-2. Display Enter the following command using the format shown below in a browser as URL, and then value of the setting item is displayed. Format http://IP address/Item IP address The IP address that is assigned to the network block Item Name of the setup item Response The following HTML is returned.
20 VPL-PX35/PX40/FX51 A-2. Setting Command Each setting item is described below. Equipment information Item Description Default location Sets location of the equipment installation. (Maximum 24 alphanumeric characters) _ Community Sets the equipment community.
21 VPL-PX35/PX40/FX51 <Table 1> <Table 2> Item Number Data Remarks Item Upper byte Lower byte Data Upper byte Lower byte VIDEO 00h 00h Set/Get S VIDEO 00h 01h INPUT 00h 01h INPUT A 00h 02h.
22 VPL-PX35/PX40/FX51 <Table 1> <Table 2> Item Number Data Remarks Item Upper byte Lower byte Data Upper byte Lower byte STANBY 00h 00h Get only START UP 00h 01h STARTUP LAMP 00h 02h POWER.
23 VPL-PX35/PX40/FX51 (VPL-PX35, PX40) <Table 1> <Table 2> Item Number Data Remarks Item Upper byte Lower byte Data Upper byte Lower byte Input 00h 01h Video 00h 00h Set/Get S-Video 00h 01.
24 VPL-PX35/PX40/FX51 <Table 1> <Table 2> Item Number Data Remarks Item Upper byte Lower byte Data Upper byte Lower byte STATUS ERROR 01h 01h NO ERROR 00h 00h Get only LAMP ERROR 00h 01h F.
25 VPL-PX35/PX40/FX51 List of SIRCS CODE (1) 15BIT Category (VPL-FX51 only) <Table 4> POWER ON/OF HUE + PURPLISH HUE _ GREENISH SHARPNESS + SHARP SHARPNESS _ SOFT ADJ R ADJ G ADJ B W/B GAIN W/B .
26 VPL-PX35/PX40/FX51 (2) 20BIT Category (VPL-FX51 only) <Table 5> x0 0x 1x 2x 3x 4x 5x 6x 7x x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF APA DOT PHASE LENS ZOOM LENS SHIFT LENS FOCUS FREEZE LE.
27 VPL-PX35/PX40/FX51 (3) 15BIT Category (VPL-PX35, PX40) <Table 6> POWER ON/OF AUDIO MUTING VOLUME- DOWN VOLUME+ UP HUE + PURPLISH HUE _ GREENISH SHARPNESS + SHARP ADJ G ADJ R ADJ B W/B GAIN W/.
28 VPL-PX35/PX40/FX51 (4) 20BIT Category (VPL-PX35, PX40) <Table 7> x0 0x 1x 2x 3x 4x 5x 6x 7x x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF APA DOT PHASE FREEZE LENS CONT TOGGLE DIGITAL ZOOM + V.
VPL-PX35/PX40/FX51 The material contained in this manual consists of inf or mation that is the proper ty of Sony Cor poration. Sony Corporation e xpressly prohibits the duplication of any portion of t.
Printed in Japan Son y Cor por ation 2003. 4 16 B&P Company ©2002 VPL-PX35 (SY) VPL-PX40 (SY) VPL-FX51 (SY) E 9-870-346-64.
デバイスSony VPL-PX35の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sony VPL-PX35をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony VPL-PX35の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony VPL-PX35の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony VPL-PX35で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony VPL-PX35を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony VPL-PX35の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony VPL-PX35に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony VPL-PX35デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
