SpecializedメーカーCR2032の使用説明書/サービス説明書
ページ先へ移動 of 17
1 SPEEDZONE ® PR0 CYCLOCOMPUTER Congratulations on your purchase! Y ou are now the owner of the world’ s most advanced cyclocomputer . Y our Specialized SpeedZone® Pro is the first cycling computer to feature wireless digital transmitters for both speed and cadence sensing.
6. Magnet with screw (1) 7. Adhesive backed magnet 8. Cadence magnet (1) 9. Cable tie wraps (6) 10. Mounting bracket sizing straps (3) 11. Speed T ransmitter and mount (1) BA TTER Y INST ALLA TION AND REPLACEMENT Before using your SpeedZone® Pro Computer you will need to install the batter y .
MOUNTING THE SPEEDZONE® PRO: There are two transmitters includ- ed with your SpeedZone® Pro. One transmitter is for speed and the other is for cadence. Please note that that they are marked with a WHEEL (speed transmitter) icon or a CRANK (cadence transmitter) icon.
road and mountain bike handlebars. Attach the mount to the handlebar using the Philips head screw provid- ed. Tighten so that the bracket cannot rotate on the handlebar . There are several sizing shims provided to fit different diameter bars. If you are using the new 31.
"SPEEDID". The "Dot-matrix Display Area" may show a number (the code of the digital speed transmitter) or "- - -". If a number is shown, press the mode button once and "- - -" will be displayed. Now , spin your front wheel to activate the transmitter .
OPERA TION AND PROGRAMMING When your SpeedZone® Pro has not detected any speed input for 30 min- utes, it will enter sleep-mode in order to conser ve batter y power . During sleep mode only the analog and digi- tal clocks are displayed. Y ou will need to wake it up by pushing the "Mode", "Set" or "T op" button once.
called the odometer mode). Note: if your display says TRIP , press the "SET" button once to change to ODO. Next, hold down the "SET" button for three seconds. The "Km" or "m" indicator will begin blinking. Y ou may now alter- nate between miles and kilometers by pressing the "MODE" button.
4. Wheel Circumference Selection T o set the circumference for the type of tires you are using, you can use Specialized’ s "Easy Calibration Mode" or measure your actual tire circumference by the rollout method. T wo dif ferent tire diameters may be entered by using the computer’ s "Second Wheel Option.
3. Roll the wheel one complete revo- lution until the valve stem is again at the 6:00 position. Read the tape directly under the valve and note the distance in millimeters.
button to adjust the hour digits. AM/PM is selected by scrolling the hour digit. Press the "SET" button to accept the hour selection. The minutes will flash and can be adjusted by pressing the "MODE" button.
set to the desired settings. Press the "SET" button to exit programming mode. Once the time inter val timer is programmed, press the "TOP" button to start/stop the countdown. (See fig- ure 15). Note: The shortest inter val that can be set is 5 seconds.
COMPUTER FUNCTIONS Speedometer (SPEED)- Y our current speed is always shown by the long needle on the LCD screen. Each needle represents one M/h when miles is selected and two Km/h when kilometers is selected. The speed is also shown on the Digital Display Area up to 99.
Inter val Timer (INT)- The inter val timer is displayed on the lower line of the screen when (INT) appears on the left. The timer indi- cates the end of an inter val with one short beep per second for the last 4 seconds of the inter val. This is fol- lowed by a long beep, indicating the beginning of a new inter val.
Programmable Odometer The odometer digits are programma- ble. This is convenient for transferring your hard-earned mileage that is usu- ally lost when changing batteries or computers. INCLINOMETER (%GRD) The inclinometer will display the per- centage of grade you are climbing or descending in increments of 1%.
Speed/distance not recording: Check sensor/magnet alignment. Make sure that the sensor is no more than 1/16" (2mm) from the magnet. Replace transmitter batter y if neces- sar y .
Automatic Timer (A TM) 0 to 9hrs, 59min, 59sec. recycling type Inter val Timer (INT) 5 seconds to 9hrs, 59 min, 59 sec. Distance Countdown(DIST ) .01 to 999.
Note: This warranty does not pertain to batteries. No person or representative is author- ized to assume any liability on behalf of Specialized Bicycle Components, Inc.
デバイスSpecialized CR2032の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Specialized CR2032をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpecialized CR2032の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Specialized CR2032の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Specialized CR2032で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Specialized CR2032を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpecialized CR2032の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Specialized CR2032に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpecialized CR2032デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。