Speco TechnologiesメーカーCS16の使用説明書/サービス説明書
ページ先へ移動 of 83
.
.
16-Channel Digital Video Recorder i WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BA CK).
Operation Instruction ii Important Safeguards 1. Read Inst ructions All the s afety and operating instructio ns should b e read bef ore the appliance is ope rated. 2. Retain Instr uction s The safety a nd operating instr uctions shoul d be retaine d for future reference .
16-Channel Digital Video Recorder iii Table of Contents Chapter 1 — Introduction ....................................................................................... ............... ..... 1 Feature ................................................
Operation Instruction iv Setup Screen .................................................................................................................. ..... 12 System Setup ............................................................................
16-Channel Digital Video Recorder v Bookmarks ..................................................................................................... ................ .. 63 Clip-Copy ......................................................................
Operation Instruction vi Figure 30 — Motion Detectio n Settings screen. ................................... .............................................. ...... 27 Figure 31 — Motion Detection Actions 1 screen. ...................................
16-Channel Digital Video Recorder 1 Chapter 1 — Introduction Feature Your color digital video recorder (DV R) provides recording capabilities for 16 camera input s.
Operation Instruction 2 Figure 1 — Typical DVR installation..
16-Channel Digital Video Recorder 3 Chapter 2 — Installation Package Contents The package con tains the following: Digital Video R ecorder Power Adaptor and Power Cord Operation Instruct.
Operation Instruction 4 Video Out NOTE: The VGA and Video Out (BNC) connectors may be connected to indi vidual monitors for simultaneous operation. Audio In/Out NOTE: It is the user’s responsibility to determine if local law s and regulations permit recording audi o.
16-Channel Digital Video Recorder 5 RS485 Port Connector Pin Outs: Master Unit Slave Unit P → To → TX+/RX+ N → To → TX-/RX- GND → To → GND Alarm Input/Output AI 1 to 16 (Alarm-In) : You can use external devices to signal the DVR to react to events.
Operation Instruction 6 To reset the unit , you will need a stra ightened paperclip : 1. Turn the DV R off. 2. Turn it on ag ain. 3. Wh ile the DVR i s initializing, th e front panel LEDs will blink. Wh en the front panel LEDs blink, poke the straightened pap erclip into the unlabeled ho le to the righ t of the VGA connector.
16-Channel Digital Video Recorder 7 Chapter 3 — Configuration NOTE: Your DVR should be c ompletely installed before procee ding. Refer to Chapter 2 — Installation .
Operation Instruction 8 Play/Stop Button Press ing the PLAY/STOP bu tton enters the playback mode, an d pressing the button again e xits the playback mode. When entering the playback mode, video is paused. Pressing the (Play /Pause) button plays back video at regular speed.
16-Channel Digital Video Recorder 9 Remote Control Buttons ID Button Camera Buttons Sequence Button Login/Logout Button Arrow Buttons Menu Button Playback Buttons Alarm Button Layout Button Zoom Button PTZ Button Enter Button Esc Button PTZ Control Buttons Copy Button Play/S top Button Figure 4 — Infrared remote control.
Operation Instruction 10 Arrow Buttons These buttons are used to na vigate through menus and GUI. You can also use them to change numbers by highlighting a number in the m enu and using the Up and Down arrow buttons to increase or decrease the number’s valu e.
16-Channel Digital Video Recorder 11 PTZ Control Buttons While in the PTZ mode, the PR ESET butt ons are used to save Presets and load a Pre set View, the ZOOM buttons are used to Zoom In and Zoom Out, and the FOCUS buttons are used for Near Focus and Far Focus.
Operation Instruction 12 Setup Screen Figure 7 — Setup screen. Press the MENU button or move the mouse pointer to th e top of the screen an d then select (Setup) in the Live Monitoring menu to enter the setup screen. While setting up the DVR, there will be many opportunities to enter names and titl es.
16-Channel Digital Video Recorder 13 Figure 9 — Information setup screen . In the Information screen, you can name the site location, assign a System ID number, se lect the language th e screens are displayed in, display software versio n number, upgrade the software, s how the System Log, displ ay recorded time data, and clear all data.
Operation Instruction 14 Highlight Show System Log… and press the button to display the S y stem Log. The System Log screen lists s y stem activities (up to 5,000 from the lates t) that have occurr ed along with the time and date. The icon will b e displayed in the last column for system activities of the remote site.
16-Channel Digital Video Recorder 15 You can set up holiday s by highlighti ng + and pressi ng the button. The current date appears. Highlight the month and day an d change th em by using the Up and Down arrow buttons. Pres s the button to add the date.
Operation Instruction 16 Highlight the box in the Format colum n for the d esired storage d evice and press the button. You will be able to format the device for recording. When selecting Not Using from Use As and highlighting the Format button, the device will not be used for recording.
16-Channel Digital Video Recorder 17 Figure 15 — User setup screen. The +/- column is used to collaps e and expand user groups. If there is a + or – in this co lumn, it indicates the item is a Group Name.
Operation Instruction 18 To add a User, h ighlight the + User… box and press the button. A virtual keyboard appears allowing y ou to enter the User Name. Enter the name and assign the User to a Group and p assword. You can use camera buttons 1 to 9 on the front panel to assign the password.
16-Channel Digital Video Recorder 19 Date/Time Setup Date: Set the system date and select the date for mat. Time : Set the system time and select th e time format. Time Zone: Select your time zone. The Time Zone can be selected on th e map.
Operation Instruction 20 Select th e Finish button to fin ish the EZ Record and select the Go to EZ Network button to start the EZ Network. Figure 18 — EZ Network screen. If you selected the Go t o EZ Ne t wor k , select the Next button to start the EZ Network.
16-Channel Digital Video Recorder 21 DVRNS Setup Use DVR Name Service: Select the box to use the DV R Name Service. DVRNS Server: Enter the IP address or domain name of the DVRNS server. Port: Set the port number of the DVRNS server. Use NAT: Select the box to use the NAT (Network Address Translation) devic e.
Operation Instruction 22 Figure 21 — Record Settings screen. Highlighting Recycle and pressing the button toggles between On and Off. In the Recycle mode, the DVR records over the old est video d ata once all av ailable storage space has been used.
16-Channel Digital Video Recorder 23 Highlighting the Panic Recording – Quality and pressing the button allows you to set the recorded image quality for Panic recording.
Operation Instruction 24 When the DVR is in the Time & Event mode, the DVR will follo w the Time settings and th e icon displays at the top-left corner of the screen. Th e DVR follows the Ev ent settings and the icon displays. Highlight the bo x under the Channels heading and pre ss the button to select which camera s will be recorded.
16-Channel Digital Video Recorder 25 Figure 25 — Pre-Event setup screen. When the DVR is in the Event Re cord mode it is possible to have it record images before the event occurs. The Pre-Event screen allows you to def ine how to handle p re-event r e cordi ng.
Operation Instruction 26 Highlight the Actions 1 and Actions 2 tabs, and the Act ions 1 and Actions 2 setup screens appear. You can set the actions the DVR will take whenever it senses an input on one of its alarm input conn ectors. Highlight the desired box under the Record heading, and press the button.
16-Channel Digital Video Recorder 27 Your DVR has built- in video motio n detection. Vi deo motion detection can be turned On or Off for each c amera. Figure 30 — Motion Detection Settings screen.
Operation Instruction 28 Highlight the box beside Daytime and press the button. Use the Up and Down arrow buttons to set the Da ytime range. The DVR will cons ider the remain ing time range as the N ighttime. Highlight the Actions 1 and Actions 2 tabs, and the Motion Detection Actions 1 and Actions 2 setup screens app ear.
16-Channel Digital Video Recorder 29 Figure 33 — Video Loss Settings screen. Highlighting the box under the Vi deo Loss Inter val heading allows you to set the duration of a signal loss before the DVR will report a Vid eo Loss.
Operation Instruction 30 Figure 35 — Video Blind Settings screen. The DVR checks to s ee if anything is bl inding a camera. Highlighting the box under the Sensitivity heading allows you to a djust the DVR’s sensitivity to video blind for Black and White independently from 0 (Never) and 1 (least sensitive) t o 15 (most sensitive).
16-Channel Digital Video Recorder 31 NOTE: For the Noti fy action, the notif y item you select should be enabled in the Notific ation setup screen and the DVR should be registered in th e Speco Central (Remote Administration System). Highlight the desired box under the PTZ heading, and press the button.
Operation Instruction 32 Highlight the more line(s) box, and press the button. Select the number o f additi onal lines of text that you want the DVR to record. You can choose from 0 to 10. Highlight the box beside Line Delimiter , and press the button.
16-Channel Digital Video Recorder 33 Figure 40 — Health Check screen The DVR can be configured to ru n self-diagnosti cs and report the results. Highlighting the box beside Sy stem and pressing the button allows you to select the interval that you want the DVR to run self-diagnostics on the s y st em.
Operation Instruction 34 Figure 42 — System Event Actions screen. The DVR can be set to react to s ystem events. System events can be associated with an Alarm-Out connector , sound the DVR’s internal buzzer, and/or notify a n umber of different devices.
16-Channel Digital Video Recorder 35 Network Setup Figure 44 — Network menu. Network Highlight Network in the Network menu and press the button. Highlight the first bo x beside Remote Watch – bps/ips . Press the Up and Down arrow buttons to set the Transfer Speed from 50Kbps to 100Mbps.
Operation Instruction 36 Highlight the LAN tab, and the LAN screen displays. Figure 46 — LAN (Manual) setup screen. Highlight the box beside Type and press the button. You can select the type of network con figuration from: Manual , DHCP and ADSL (with PPPoE) .
16-Channel Digital Video Recorder 37 Selecti ng DHCP from t he Type and hi ghlightin g Save button reads the current IP address of the DVR configured by DHCP (Dynamic Host Configuration Pr otocol) network. Highlight Auto (Def ault) and press the button to toggle between On and Off.
Operation Instruction 38 Highlight the Check box and press the button to check whether or not the name you entered can be used. NOT E: The DVR name you e ntered should be chec ked by selecting Ch eck, otherwise the DVRNS changes w ill not be saved. When entering no name or a name alread y registered on the DVRNS ser ver, an error message di splays.
16-Channel Digital Video Recorder 39 The DVR can be set up to contact a com puter running Speco Central (Remote Administration Sys tem) when an ev ent occurs. Highlight the box under the No. heading and pres s the button to toggle betw een On and Off.
Operation Instruction 40 Highlight the box beside Port and press th e button. Use the arrow buttons to enter the SMTP Server port number obtained from your s ystem administrato r. The default port number is 25. Highlight Use SSL/TLS and press th e button to toggle between O n and Off.
16-Channel Digital Video Recorder 41 Figure 53 — Notification Schedule setup screen. You can add and edit notification schedules on this screen . Highlight the + and press th e button to add a schedule. Highlighting the boxes under the Column heading and pressing the button allows you to edit the information in those boxes.
Operation Instruction 42 Figure 55 — Camera setup screen. You can turn the cam era number On or Off, and you can change the Titl e of each camera using the virtual keyboard. You can also det ermine which ca meras will display on the monitors by selecting Normal, Covert 1 or Cove rt 2 from a drop-down list in the Use column.
16-Channel Digital Video Recorder 43 Audio Highlight Audio in the Devices menu and pr ess the button. The Audio setup screen appears. The DVR can record up to four audio inputs. Hig hlight the box besi de the inp ut and pres s the button. A list of cameras appears, and you can selec t which cam era you want ass ociated with that audio input.
Operation Instruction 44 The Mode box allows you to set how the alarm reacts dur ing the scheduled time. When set to On , the Alarm-Out is active during th e scheduled time. Wh en set to Event , the Alarm- Out is only active wh en there is an Event during the scheduled time.
16-Channel Digital Video Recorder 45 Highlight the box beside Channels and press the button. You can select the c a meras with record ed audio you want to extract audio files from . Highlight th e box beside From and press the button to toggle betwe en On and Off.
Operation Instruction 46 Highlighting OSD Margin… and pressing the button display s how OSD text will be displayed on the monitor. You can adju st the horizontal and ver tical margins so that text and i cons will not be hidden beyond th e edges of the monitor.
16-Channel Digital Video Recorder 47 Remote Control Highlight Remote Control in the Devices menu and press the button. The Remote Control se tup screen allows you to select a port and make correct settings for a remote keybo ard. Highlight the box bes ide Port and select from None, RS232 and RS485.
Operation Instruction 48.
16-Channel Digital Video Recorder 49 Chapter 4 — Operation NOT E: This chapter assume s your DV R has been installed and configured. If it has not, please ref er to Chapters 2 and 3. The DVR’s c ontrols are si milar to a VCR . As with a VCR, the main f unctions a re record ing and play ing back vi deo.
Operation Instruction 50 NO TE : The location of camera screen can be changed by using the mouse. When in one of the multivie w formats, click the left mouse butto n on the camera screen and dra gging it to where you w ant it located, and the location of two camera screens will be switched each other.
16-Channel Digital Video Recorder 51 Audio: Selecting Audio toggles au dio output On and Off. Color Contr ol: Selecting Color Control and ch oosing the camera number allows y ou to control brightness, contrast, hue and saturatio n for each camera for the s elected cam era if a user who has Color Control authority logs in to the system.
Operation Instruction 52 Active Cameo Mode You can enter the Active Cameo mod e by selecting (Display) Edit Group in the Live Monitorin g menu in any multi-view format. The y ellow outline surrounding the video indicates the active cameo, and pressing the arrow b uttons moves the active cameo.
16-Channel Digital Video Recorder 53 You can save camera position settings as “presets” so that you can go directly to desired views. Once you have th e camera at th e desired settings, press the PRESET SET button, and the Set Preset dialog box will appear.
Operation Instruction 54 Covert Camera If a camera is set up as Covert 1 in the Camera setup screen (Set tings tab), that camera will not be displa yed unless a user with Covert Camera View authority logs into the s y stem. H owever the camera title and status icons will be displayed on the monitor.
16-Channel Digital Video Recorder 55 Selecting All Ch annels plays back video of all cameras. The DVR maintains the same display format as it does in the live mode except for the PIP format. You can also change the sc reen layout in the sa me way as you do in the live mode.
Operation Instruction 56 Display Search Go To Bookmark Export Camera Menu Alarm Digital Deterrent Panic Data Source Exit Figure 69 — Search menu. NOTE: The Search menu also ca n be displayed by moving the mous e pointer to the top of the scree n. Search Menu Display Selecting (Display) in the Search menu disp lay s the following Display Menu .
16-Channel Digital Video Recorder 57 Move the cursor over the date and time and press the (Play/Pause) button. You can use the Left and Right arrow buttons to highlight the year, month, day, hours, minutes and seconds. Use the Up and Down arrow buttons to change to the date and time you want to search for video.
Operation Instruction 58 Data Source Selecting (Data Source) in the S earch menu allow s you to select the data so urce to be searched. Selecting Record searches recorded data on primary storage installed in the DVR, and selecting O t her searches recorded data on storage used for another D VR then installed in this DVR.
16-Channel Digital Video Recorder 59 Highlight the box beside Video Loss and press the button. You can se lect the ca meras for which you want any reports of lost video. Highlight the box beside Video Blind and press the button. You can select the cameras for which you want any reports of blind v ideo.
Operation Instruction 60 Selecting or located at the botto m zooms the record table. Selecting displays eight hours (1-minute based), and selecting displays 24 hours (3-minute based) at once.
16-Channel Digital Video Recorder 61 Motion Search Figure 73 — Motion Search screen. The Motion Search … can be selected from the Search menu while the DVR displays the camera full sc reen. The Motion Search screen displays a list of motion ev e nts.
Operation Instruction 62 Text-In Search Figure 74 — Text-In Search screen. The DVR maintains a log of each time there is Text Inpu t. The Text-In Search screen displays this list. Use the arrow buttons to highlight the ev ent for which you would lik e to see video.
16-Channel Digital Video Recorder 63 Bookmarks The Bookmarks screen can also be accessed by selecting (Bookmark) in the Search menu when in playback mode. Highlight + and press the (Play /Pause) button to add the current playback point to the bookmark list.
Operation Instruction 64 CAUTION: The USB device for clip copy must be FAT 16 or FAT32 format. The DVR automatically assigns a file name to the video clip. However, you can give the video clip file a different name. Highlight the box beside File Name and pr ess the button.
16-Channel Digital Video Recorder 65 Appendix USB Hard Disk Drive Preparation Preparing the USB hard disk drive in Windows 2000 NOTE : Preparing a USB hard disk drive under Wind ows XP, Window Vista and Wi ndow 7 is almost id entical to Windows 2000. 1.
Operation Instruction 66 Text-In Search Examples Search Example I 1 2 3 4 5 6 123456789012345678901234567890123456789012345678901234567890 Item Unit price Qty amount ================================================== Coke | $ 2.20 | 1(s) | $ 2.20 Fanta | $ 2.
16-Channel Digital Video Recorder 67 For example, if you want to search fo r Coke with a Qty (Quantity) of more than 1 an d Hotdog with an amount totaling over $8, the following sear ch condition can be set.
Operation Instruction 68 NOT E: There might be a problem th at the bottom of Speco Remote page i s cropped due to the address o r status bars in Mic rosoft Internet E xplorer 7.0. In th is situation , it is recommended that websit es open w indo w s without address or status bars by changi ng the internet setti ng.
16-Channel Digital Video Recorder 69 ⑦ Click the to adjust the brightness, contrast, saturation and hue o f monitoring image. ⑧ Click the to control pan, tilt a nd zoom of the c amera from a r emote site. ⑨ Click the to control alarm out devices at the remote site.
Operation Instruction 70 ① Click the to log out the Speco Re mote program. ② Click the to access to the web monitoring mode. ③ Position the mouse pointer on the Remote Search logo to see the versio n of the Speco R emote program.
16-Channel Digital Video Recorder 71 ⑭ Selecting a camera on the screen and clicking the right mouse button displays the text menu s creen. Change Camera Title : Changes the camera n ame. Enable Audio : Plays audio while playing back record ed video that has recorded audio.
Operation Instruction 72 Map of Screens.
16-Channel Digital Video Recorder 73 Troubleshooting Problem Possible Solution No Power Check power cord co nnections. Confirm that there is power at the outlet. No Live Video Check camera vi deo cable and connections . Check monitor video cable and connections .
Operation Instruction 74 Error Code Notices System Upgrade R elated Clip Copy Related No. Description No. Description 0 Unknown error. 0 Unknown error. 1 File version erro r. 1 Device error. 2 Operating system version error. 2 Mounting failed. 3 Software version error.
16-Channel Digital Video Recorder V1.0 75 INPUTS/OUTPUTS Alarm Input 16 terminal, programmable as NC or NO, 2.4V (NC) or 0.3V (NO) threshold, 5VDC Alarm Output 1 relay output, 2A@125VAC, 1A@30VDC (NO).
デバイスSpeco Technologies CS16の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Speco Technologies CS16をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpeco Technologies CS16の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Speco Technologies CS16の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Speco Technologies CS16で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Speco Technologies CS16を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpeco Technologies CS16の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Speco Technologies CS16に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpeco Technologies CS16デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
