Speco TechnologiesメーカーHT-7248FFIの使用説明書/サービス説明書
ページ先へ移動 of 24
HT7248FFi 540 Line Color Dome Camera Intensifier Series, Focus Free Wall & Ceiling Mountable Please read this manual thoroughl y before operation and keep it handy for further reference.
WARNING & CAUTION The lighting flash with an arrowhead symbol, within an eq uila te ral t ri ang le is Intended to alert t he u se r t o t he pre se nce of un- in sul ate d “ dan ger ou s v olt .
Contents 3 Package Contents 4 Preca utions 5~8 Camera Installation 9~10 Features 11~16 OSD Setting 17~18 Troubleshooting 19 Spec ification 20 Dimensions 21 War rant y 2.
PACKAGE CONTENTS • Please make sure that t he following it ems are included in the pack age: 1 HT7248FFi Camera 2 Mounting Screws 1 Chame leon Dome Cov er 1 Video Test Cable Pleas e leav e this manu al with the end-u ser for future reference.
PRECAUTIONS • THIS DOME CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED PERSONNEL • TO PREVENT A FIRE OR ELECTR ICAL HAZARD PLEASE USE PROPER POWER CABLE.
CAMERA INSTALLATION 1. CONNECT POWER CABLE 1) WHEN USING 12 VOLTS DC (constant voltage 600 mA) -CONNECT ACCESSORY CABLE TO THE CABLE LEAD OF THE CAMERA AND CONNECT 12V DC POWER SUPPLY. 2) WHEN USING 24 VOLTS AC (40 Volt Amps) 3) CONNECT VIDEO CABLE -CONNECT BNC CABLE TO THE BNC JACK.
CAMERA INSTALLATION 2. CHAMELEON COVER INST ALLATION 1) If you wish t o change the color of the HT-7248FFi, place the Ch ameleon Dome o ver the camera * Spray the color of y our choice onto the Cham e.
CAMERA INSTALLATION 3. CONTROL BOARD 1) Video Test Term inal For second video ou tput 2) OSD (On S creen Dis play) Joy stick Press the Joy stick for one second until the OSD menu tree appears on the sc reen. Move the Joy Stic k up, down, left & right to contr ol the OSD func tions.
CAMERA INSTALLATION 4. DIP Switch Setting f or RS-485 (Pelco-D) 2) Baud rate S etting to set Baud rate, please refer the chart below. 1 2 3 4 5 6 1) Ad dress Settin g to set Camera Address, place s witches based on belo w chart.
Feature s SLC When the image is in front of strong background lighting, your camera allo ws you to get a clear image. INTE NSIFIER 1/3 inch density CCD and d igital processor permit high qualit y pictures to be captured in very lo w light condition.
OSD All camera functions are menu driven for easy use. Dynamic Noise Reduction The Intensifier camera has a DSP chip that can remove image noise efficiently showing clean images in low light con ditions.
Operating y our camera OSD Function SETUP MENU LENS TYPE ● DC IRIS SHUTTER TYFE ● ELC ● FIXED ● MANUAL WHITE BALANCE ● ATE ● AWC ● MANUAL SLC ● HIGH ● MIDDL E ● LOW ● OFF AUTO GA.
SETUP Menu Functions 1. LENS ( DC) – Lens is s tatic wit h DC aut o iris lens on ly 2. SHUTTER (Option : OFF / FLK / MANUAL/ E SC) Flickerl ess mode (FLK) reduces on-sc reen flickering. Electronic Shu tter Control ( ESC) adjusts b rightness level on screen.
5. Auto Gain ( Low / Middle / High) Increase the GAIN leve l to brighten the picture. (noise / dist ortion may dev elop) 6. REDUCE NOISE (Lo w / Middle / High) Reduces noise/dis tortion on the screen, Inc reasing the REDUCE NOISE le vel reduces noise but may introduce video Artifacts, it is deactivated if AGC is turned off.
NEXT PAGE Menu Functions 1. CAMERA ID UP, DOWN , LEFT, RIGHT menu control = Select a character , then press (SETUP)MEN U to accept it. The character is saved and the title cursor at the bottom of the screen mo ves to the next pos ition. ←→ = Go back or forward in the title name to make changes.
3. SYNC (INT / Lin e Lock) INT : When line lock is not required. It synchroni ze the vertical interval sync p ulse of your camera w ith other equip ment to reduce the effect of picture roll on t he monitor. L/L : Adjust the vert ical phase (VPH) from 000 ~ 359 Line L ock is only availabl e with 24VA C power.
5. PRIVACY Allows you to mask certain a reas of the screen from observation AREA SEL = Select a motion detection grid (top left, top right, bott om left, bottom right) to modify.
Troubleshooting If you have trouble operating yo ur camera, refer to the followi ng ●H a v e y o u s e t ‘ MOTION DET. ’ menu to off? ●H a v e y o u s e t ‘ MD LEVEL ’ to too how? ●H a v e y o u s e t ‘ MD ARAEA ’ pro perly MOTION DETECTION function is not active.
● Have you connected yo ur camera to DC power source? Connect it to AC pow er source. L/L mode isn ’ t able to be selected. ● Is the camera facin g t o direct sunlight or fluorescent lighting? Change the camera posi tion. The image on the screen flickers.
SPECIFICATIONS Internal / Line Lock selectable Synchronization Focus F ree Lens 3.5~10 mm LENS TYPE 500mA (DC ) / 6.6W (A C) Power Consump tion -29 ℃ ~ +50 ℃ ( - 20 ℉ ~122 ℉ ) Operation al Temperature ON / OF F (4 Prog rammable Zone) PRIVACY Function Built – in On Screen Display ( O.
DIMENSIONS * SIDE VIEW * TOP VIEW 20.
WARRANTY 21.
MEMO.
200 New Highway Amityville, NY 11701 631-957-8700 www.spe cotech.com VER. 080901 This manual is ba sed on the date as shown in the right and specification s are subject to Change w ithout notice for quality improvement.
デバイスSpeco Technologies HT-7248FFIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Speco Technologies HT-7248FFIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpeco Technologies HT-7248FFIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Speco Technologies HT-7248FFIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Speco Technologies HT-7248FFIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Speco Technologies HT-7248FFIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpeco Technologies HT-7248FFIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Speco Technologies HT-7248FFIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpeco Technologies HT-7248FFIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。