SprachtメーカーCP-2012の使用説明書/サービス説明書
ページ先へ移動 of 19
V oice Center ™ Conference Phone Model CP-2012 User's Manual.
T able of Contents - V oice Center User’s Manual Introduction and Quick Start Guide Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Thank you for choosing the V oice Center Conference Phone, a high per formance audio conferencing system. Its features include: • Full duplex communication – the V oice Center’ s digital speech processing enables simultaneous two-way communication.
3 Quick Start Guide 3. Analog or Digital T elephone System? Caution: if the V oice Center is connected to a digital telephone system using the Analog T elephone System Inter face, it will not operate correctly , and may cause damage to the A T -103 Analog Interface and cause it to over heat.
Analog T elephone System Setup with Analog T elephone System If you are connecting the V oice Center Conference Phone to an analog telephone system, follow the instructions below .
W all Mounting of Analog Interface (Optional) • Install the two mounting screws supplied with the Analog Inter face in the wall. Leave approximately 3/16 in. (0.5 cm) between screw head and wall. • Place the Analog Inter face over the mounting screws and slide it down to fix it in position.
Keypad Functions with Analog Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to obtain a dial tone, or turns it off to terminate a call.
Conference Phone Operation with Analog Phone System Answering a call When the Conference Phone rings, press the ON/OFF key to answer the call. The green LED illuminates to indicate the Conference Phone is on.
Digital T elephone System Setup of Conference Phone with Digital Phone System Note: The DT -104 Digital T elephone System Inter face is required for use of the Voice Center Conference Phone with a digital phone system. Follow the steps below to set up the system.
4. Use Digital Inter face’s 4-position switch to adjust audio level by making a test call. • Lift digital telephone handset from its cradle, then press Conference Phone’ s “On/Off” key .
Keypad Functions with Digital Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to connect a call, or turns it off to terminate the Conference Phone conversation. When the Conference Phone is on, green LEDs illuminate by all active microphones.
Conference Phone Operation with Digital Phone System Answering a call 1. When the phone rings, pick up the digital telephone handset to accept the call.
General Setup T ips T ips for Obtaining Optimal Acoustic Performance • T o minimize echoes, place the Conference Phone at the center of the room, or at least away from walls (at least 20 inches/0.5 m from any wall). • It is impor tant to place the Conference Phone on the sur face where it will be used before applying power .
'ENERAL )NSTALLATION OF %XTERNAL -ICR OPHONES /PTIONAL 4HE 6 OICE #ENTER #ONFERENCE 0HONE HAS BUILTIN MICROPHONES FOR COMPLETE .
Specifications Conference Phone Controls and Interface Switches Microphone switch to turn on T one/pulse switch to select 2, 3 or all 4 built-in microphones telephone dialing mode LED indication light.
Spracht Limited W arranty Policy Spracht warrants it products against defects or malfunctions in material and workmanship under normal use and ser vice, with the exceptions stated below . This warranty lasts for one year from the original date of purchase.
16.
Federal Communications Commission Statement Note: The V oice Center Conference Phone equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SPRACHT T el: 650-318-8061 Fax: 650-318-8060 2672 Bayshore Parkway , Bldg 900 Mountain View , CA 94043 USA www .spracht.com © 2003 Spracht Spracht and V oice Center are trademarks of ODI.
デバイスSpracht CP-2012の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Spracht CP-2012をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpracht CP-2012の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Spracht CP-2012の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Spracht CP-2012で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Spracht CP-2012を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpracht CP-2012の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Spracht CP-2012に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpracht CP-2012デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
