Standard HorizonメーカーGX1250Sの使用説明書/サービス説明書
ページ先へ移動 of 20
GX1250S Horizon Ec lipse+ 25 watt VHF/FM Marine T ransceiver Owner’ s Manual S ta n d a rd C om m u ni c a t i o n s.
T ABLE OF CONTENTS GENERAL INFORMATION .....................................................................1 INTRODUCTION......................................................................................1 FCC/DOC INFORMATION......................
1 GENERAL INFORMA TION 1.1 INTR ODUCTION The Standard Communications Corp. (SCC) GX1250S Eclipse+ is a VHF transceiver designed for use in the frequency range of 156.050 to 163.275 MHz. It requires 13.8 VDC for operation. The transceiver has 65 channels: 55 marine and 10 weather.
Additional FCC and DOC data, including licensing requirements, are contained in the companion document titled OWNER’S MANUAL SUPPLEMENT. The document also contains charts for VHF channel assignments, transceiver procedures, maintenance, factory service information, and warranty data.
3 CONTR OLS AND INDICA T ORS Refer to Figure 1 for the location of the following controls, indicators, and connections: 3.1 CONTR OLS AND CONNECTIONS q q POWER SWITCH/VOLUME CONTROL Turns the transceiver on and off, and adjusts the volume.
Owner's Manual GX1250S Page 4 Horizon ECLIPSE + UP H / L SCAN DN WX 16 / 9 R / D SQL VOL U I C • • DN UP q q w w e e r r t t y y u u i i o o ! ! 0 0 Figure 1.
SCAN KEY Starts and stops scanning programmed channels. Holding down this key, scanning channels are programmed. 16/9 KEY Immediately recalls channel 16 from any channel location. Holding down this key recalls channel 9. When held down while pressing the WX key, changes the mode from USA to International or Canadian.
! ! 1 1 UP KEY Selects the desired channel. Each press increases the channel number. When held down the channel numbers increase continuously. ! ! 2 2 DOWN KEY Selects the desired channel. Each press decreases the channel number. When held down the channel numbers decrease continuously.
TX Indicator Transmission indicator. The TX indicator appears when th PTT switch is pressed and it is O.K. to transmit. MEM Indicator Indicates the channel is memorized in the transceiver’s memory. A Indicator Indicates a simplex channel in USA or Canadian mode whose counterpart in the International mode is a duplex channel.
Owner's Manual GX1250S Page 8 4 INST ALLA TION 4.1 FREQUENCY AND DEVIA TION TESTS FCC regulations require that the transceiver’s deviation and frequency be tested before initial installation or operation. This test should be performed by a Certified Marine Technician.
Owner's Manual GX1250S Page 9 Figure 3. General Installation Figure 4. Regular Mounting Bracket Figure 5. CMB16 Mounting Bracket SPEAKER (OPTIONAL) BATTERY WATERPROOF DECK OUTLET.
Owner's Manual GX1250S Page 10 4.3 INST ALLA TION USING REGULAR MOUNTING BRA CKET 1. Mount the bracket using the washers, nuts, and long hex head bolts. 2. Thread the mylar washers onto the mounting bracket knobs. 3. Position the transceiver within the bracket arms, matching the transceiver notches to obtain the desired positioning.
5 OPERA TION After the transceiver has been installed (see section 4), ensure the power supply and antenna are properly connected. 5.1 RECEPTION 1. Turn the POWER SWITCH/VOLUME CONTROL on. 2. Turn the volume control knob to the desired level. 3. Turn the SQUELCH CONTROL knob fully counterclockwise.
Owner's Manual GX1250S Page 12 3. Press the PTT (push - to - talk) switch. The TX indicator in the LCD is displayed. 4. Speak slowly and clearly into the microphone, hold the microphone about 1/2 to 1 inch away from your mouth. 5. When the transmission is finished, release the PTT switch.
5.6 SCANNING 1. Adjust the SQUELCH CONTROL until the background noise disappears. 2. Select the desired channel to be scanned using the UP or DN key. 3. Hold down the SCAN key until “MEM” is displayed. 4. Repeat steps 2 and 3 for the channels to be scanned.
5 . Even when the transceiver stops and listens to the signal of a memorized channel, the transceiver will DUAL WATCH between this channel and the priority channel. 6. To disable priority scanning, turn off the transceiver power. Press and hold the SCAN key and turn the power back on.
5.9 EMERGENCY CHANNEL 16 1. To select the emergency channel, press the 16/9 key from any channel. 2. Transmit your emergency signal in the same manner as on regular channels. If you can not contact anyone on channel 16, switch to another channel. 3. See the OWNER’S MANUAL SUPPLEMENT for additional emergency operating practices.
Owner's Manual GX1250S Page 16 6 MAINTENANCE For preventive maintenance and instructions on obtaining factory service, please refer to the OWNER’S MANUAL SUPPLEMENT. For general troubleshooting, refer to the Troubleshooting Chart. TROUBLESHOOTING CHART PROBABLE CAUSE No DC voltage to the transceiver or a blown fuse.
7 SPECIFICA TIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 7.1 GENERAL Frequency Range..............................................................156.050 to 163.275 MHz Channels ..
S ta n d a rd C om m u ni c a t i o n s Standard Communication Corp. P.O. Box 92151 Los Angeles, CA 90009-2151 Telephone 310/532-5300 © STANDARD COMMUNICATIONS CORP.
デバイスStandard Horizon GX1250Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Standard Horizon GX1250Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStandard Horizon GX1250Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Standard Horizon GX1250Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Standard Horizon GX1250Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Standard Horizon GX1250Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStandard Horizon GX1250Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Standard Horizon GX1250Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStandard Horizon GX1250Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。