Stanley Black & DeckerメーカーCS05/CS06の使用説明書/サービス説明書
ページ先へ移動 of 24
© 2012 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66864 1/2013 V er . 7 S afety , O pera tiOn and M aintenance USer ManUaL CS05/ CS06 HYDRAULIC CHAIN SA W.
.
CS05/CS06 User Manual ◄ 3 T ABLE OF CONTENTS WARNING SERIOUS INJUR Y OR DEA TH COULD RESUL T FROM THE IMPROPER REP AIR OR SER VICE OF THIS TOOL. REP AIRS AND / OR SERVICE T O THIS TOOL MUST ONL Y BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. SERVICING: This manual contains safety , operation, and routine maintenance instructions.
4 ► CS05/CS06 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte - nance personnel.
CS05/CS06 User Manual ◄ 5 SAFETY PRECAUTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety .
6 ► CS05/CS06 User Manual SAFETY PRECAUTIONS – maintenance instructions for the saw chain. – Only use replacement bars and chains specied by Stanley Hydraulic T ools. Chains must meet the requirements of ANSI B175.1 for low kick - back performance.
CS05/CS06 User Manual ◄ 7 ELECTRICAL PRECAUTIONS The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables.
8 ► CS05/CS06 User Manual ELECTRICAL PRECAUTIONS T able 2 – Minimum approach distances to energized conductors for persons other than qualied line-clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.
CS05/CS06 User Manual ◄ 9 T OOL STICKERS & T AGS 28323 CE Decal (CE Models Only) 28409 Composite Decal (CE Models Only) D 30 LPM @ 138 BA R EHTMA CA TEGORY 1 1207 Circuit T ype D Decal (CE Model.
10 ► CS05/CS06 User Manual HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy - draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
CS05/CS06 User Manual ◄ 1 1 HOSE RECOMMENDA TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose -.
12 ► CS05/CS06 User Manual HTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
CS05/CS06 User Manual ◄ 13 OPERA TION OPERA TING PROCEDURES The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less val - id for particu lar areas.
14 ► CS05/CS06 User Manual OPERA TION FELLING OR BACK CUT 4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in.
CS05/CS06 User Manual ◄ 15 OPERA TION Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on T op LOGS WITH PRESSURE ON TOP (FIGURE 3) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply .
16 ► CS05/CS06 User Manual OPERA TION Figure 6. Crosscutting Thick Logs with Pressure on Bottom LOGS/LIMBS WITH PRESSURE ON BOTTOM (FIGURE 5) 1. Observe all safety precautions. 2. Begin with a bottom cut. The depth of the cut should be about 1/3 of the log diameter .
CS05/CS06 User Manual ◄ 17 OPERA TION PRUNING AND DEBRANCHING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. 4. Do not cut overhead.
18 ► CS05/CS06 User Manual T OOL PROTECTION & CARE • Make sure all couplers are wiped clean before con - nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools.
CS05/CS06 User Manual ◄ 19 TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table.
20 ► CS05/CS06 User Manual SPECIFICA TIONS Capacity CS05 ..................................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 .............................................
CS05/CS06 User Manual ◄ 21 CS05/CS06 P ARTS ILLUSTRA TION.
22 ► CS05/CS06 User Manual CS05/CS06 P ARTS LIST ITEM NO. P ART NO. QTY DESCRIPTION 1 00753 09622 8 CAPSCREW CAPSCREW U/W MODEL 2 07636 08202 1 NAME T AG—CS06 NAME T AG—CS05 3 28323 1 CE DECAL (.
CS05/CS06 User Manual ◄ 23 P ARTS LIST ITEM NO. P ART NO. QTY DESCRIPTION 71 07610 1 SPRING 72 00190 1 ROLL PIN 73 10537 1 KEEPER 74 07625 1 PLUG BUTTON 75 03786 1 GPM STICKER (7–9 GPM) 03782 1 GP.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.
デバイスStanley Black & Decker CS05/CS06の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Stanley Black & Decker CS05/CS06をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker CS05/CS06の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker CS05/CS06の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker CS05/CS06で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker CS05/CS06を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker CS05/CS06の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker CS05/CS06に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker CS05/CS06デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
