AcerメーカーIDM2の使用説明書/サービス説明書
ページ先へ移動 of 28
,'0+RXVLQJ ,QVWDOODWLRQ*XLGH.
Installation Guide ii &RSU LJKW Copyright 1998 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retriev al system, or .
IDM Housing iii ,03257$176$)(7< ,16758&7,216 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all w arnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning.
Installation Guide iv 10. If an extension cord is used w ith this product, make sure that the total ampere rating of the equipment plugged into the ex tension cord does not exceed the ex tension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.
IDM Housing v 16. Use only the proper type of pow er supply cord set (prov ided in your keyboard/manual accessories box ) for this unit. It should be a detachable type: UL listed/CSA certified, type SVT /SJT, rated 6A 125V minimum, VDE approved or its equivalent.
Installation Guide vi )&&&ODV V%5D GLR )UHTXHQF ,QWHUIHUHQFH6WDWHPHQW Note: This equipment has been tested and found to comply w ith the limits for a Class B digital device, pursuant to Part 15 of FCC R ules.
IDM Housing vii $ERXWWKLV0DQ XDO Purpose This manual aims to give y ou all the information you need to install the system housing. Conventions The follow ing conventions are used in this manual: NOTE Gives bits and pieces of additional information related to the current topic.
Installation Guide viii.
IDM Housing ix 7DEOHRI&RQ WHQWV 1 Introduction ................................................................................ 1 2 Standalone Sy stem .................................................................... 1 3 Features ........
IDM Housing 1 1 Introduction This installation guide describes the features of the IDM housing and tells you how to install the basic sy stem components such as disk drives, a sy stem board, or ex pansion boards. Descriptive illustrations accompany the installation procedures.
Installation Guide 2 3 Features 3.1 Front Panel Keyloc k Panel Door.
IDM Housing 3 3.2 Rear Panel Power Suppl y Power Socket COM por t slot s Expansi on P or t Slot s Expansi on S lots SCSI E x pansion Slots Housing Fan Syst em Boar d connector s.
Installation Guide 4 3.3 Internal Structure The figure below shows the housing internal structure and some of the basic system components. Power Suppl y Backpl ane B oar d Hot-Sw ap Cag e (SCSI ) 5.25-inch Dri v e B ays Expansi o n Card Slot s Housing Fa n 3.
IDM Housing 5 4 Opening the Housing Panel s 4.1 Front Panel Unlock the housing with the key and then pull the panel to access the drive trays. Keyloc k.
Installation Guide 6 4.2 Left Panel To remove the left panel: 1. Use a screw driver to remove the tw o screw s securing it to the rear panel. 2. Pull the panel handle to slide the left panel open.
IDM Housing 7 5 Installing Disk Drives and Hot-Sw ap Cage Turn off the power switch and unplug the power cord before installing or removing diskette drives. 5.1 3.5-inch Drive 1. Open the front panel and remove the left panel of the housing. See section 4 for more information on opening the housing panels.
Installation Guide 8 4. Insert the drive into the drive bay and secure it with tw o screws. 5. Connect the diskette drive cables. 5.2 5.25-inch Driv es You may install a C D-RO M, digital audio tape (D AT), hard disk, diskette drive or any other 5.25-inch device into the driv e bay.
IDM Housing 9 4. Insert the drive into the drive bay and secure it with tw o screws. 5. Connect the signal and power cables to the driv e. 5.3 Hot-Swa p Cage The hot-sw ap cage box includes the follow.
Installation Guide 10 2. Attach the driv e guides on the sides of the hot-sw ap cage w ith two screws on each side. 3. Insert the hot-swap cage into the housing and secure the hot-swap cage with tw o screws.
IDM Housing 11 4. Attach the power cable, the SCSI term inator, the HDD fault L ED cable , and the system board connector cable to the backplane board and attach the other end of the connector cable to the system board. For the location of the SCSI connector, please refer to the system board manual.
Installation Guide 12 Cascading Hot-swap Cage Configuration The SCSI connector cable and the three- connector HDD fault LED cable is an optional item needed for installing two hot-swap cages.
IDM Housing 13 SCSI Connector Cable 5.4 Hard Disk Driv e Tray 1. Use your finger to release the drive tray as shown below and then pull it out. 2. Place a hard disk on the tray. Secure it with four screws and four metal support braces as shown below .
Installation Guide 14 4. Insert the tray into the hot-swap cage and then close the lever as shown below. 6 Installing a Sy stem Board The housing accommodates various sy stem board sizes. Y ou can rearrange the pegs on the system board plate to fit the board that you w ish to install.
IDM Housing 15 7 Installing an Expansion Board 1. Remove an ex pansion slot bracket cover. Sav e the screw to secure the expansion board. 2. Align an expansion board w ith the open slot and insert the golden fingers into the expansion bus connector. 3.
Installation Guide 16 8 Install i ng a CPU or M emor y Board Follow these steps to install a CPU or memory board if your sy stem board does not include them. 1. Remove a bracket opposite the CPU or memory board slot. 2. Insert the board into the slot.
IDM Housing 17 5. Insert the right end of the bar into the hole near the hard disk driv e frame and the left end into the hole on the rear panel. Left End Right End.
Installation Guide 18 9 LVD SCSI Backplane Board The LVD SCSI hot-sw ap cage includes a hot plug SCA single-ended backplane, LED board, and the hard drive cage itself. It supports three 1-inch SCA-II SCSI hard drives in one channel w ith active terminator built-in.
IDM Housing 19 Connector Description CN7 Slot 2 CN8 SCSI 68-pin connector - Out CN9 Slot 3 JP5 Power connector S1 Slot 1 ID switch S2 Slot 2 ID switch S3 Slot 3 ID switch.
デバイスAcer IDM2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Acer IDM2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAcer IDM2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Acer IDM2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Acer IDM2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Acer IDM2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAcer IDM2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Acer IDM2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAcer IDM2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。