Star MicronicsメーカーTUP992の使用説明書/サービス説明書
ページ先へ移動 of 37
1 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088371 Date: 12/3/2007 TUP900 Revision 1.2.
2 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088372 Date: 12/3/2007 • Getting Started o Cable Connections - 4 o Loading Paper – 5 o Paper Feed Sensor Adjustment - 7 • D.
3 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088373 Date: 12/3/2007 Getting Started.
Assembly – Installing the Interface Place the interface sub-assembly into the interface slot as shown. Take care to be sure the interface cartridge is seated properly into its connector. Using a #2 Phillips scr ewdriver, install the mounting screws included with the printer.
Assembly – Paper Roll Setup It is necessary to adjust the paper roll holder for the width of the pape r you use. If the setting position is incorrect, the paper roll will be supplied improperly to the mechanism which in turn causes paper transport problems.
Assembly – Paper Rol l Setup Continued Once the paper roll holder is properly configured for the roll to be used, simply insert the roll holder into the paper core as show. Be sure that the cut end of the paper roll is properly cut to ensure proper paper loading.
TUP900 Paper Feed Sensor Adjustment – See photos below This is a multi-step process: 1. Ensure that the paper is loaded on the spindle and that the two black plastic sleeves are positioned on eithe r sid e of the paper roll in order to keep the roll centered on the spindle and fr om sliding left or right.
8 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088374 Date: 12/3/2007 Driver Installation.
9 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088375 Date: 12/3/2007 DRIVER INSTALLATION: Step 1 To download drivers from our website – go to the below link: http://www.
10 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088376 Date: 12/3/2007 Step 4 When your printer has been successfully installed, it will create a printer icon in Printers and Faxes.
11 Step 3 If you intend to use the status monitor function to get status from the printer (recommended for parallel .
12 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088378 Date: 12/3/2007 Step 7 Click on the last opt ion – Install from a list .
13 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 088379 Date: 12/3/2007 Step 9 Click on Have Disk.. Step 10 Click on Brow.
14 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883710 Date: 12/3/2007 Step 12 Choose the TUP900 with out Status Monitor and click Next Then click Next to finish the driver installation.
15 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883711 Date: 12/3/2007 Troubleshooting.
1 6 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883712 Date: 12/3/2007 TROUBLESHOOTING: Below is a list of common issues that may .
Power LED Error LED Red Green SW2 SW1 CHAPTER 6 OPERA TION SPECIFICA TIONS 6-1 Operation Panel Specifications ------------------------------------------------------------------------------------------.
1 When Power is ON SW Input Operation SW1 Self-test Print SW2 Hex Dump Mode 2 When in Sensor Adjustment Mode and Power is ON (Sensor Adjustment Mode is selected using by setting the DIPSW1-4 on the main board to OFF .
This error automatically cancels E errors by varying the status internally on the printer . Error LED Cause How to Recover Power Error Printing Stops Because Blink OFF Head Thermistor Automatic Recove.
This error requires the printer to be reset after executing a determined error recovery means because a fatal error has occurred. The printer many need to be repaired if the same error occurs even after resetting the printer .
Dip Switch Setting: 1) When mounted with a parallel interface <At Ex-factory: All are turned ON.> DIPSW1 Function ON OFF DIPSW1-1 Emulation See table below *2 DIPSW1-2 Emulation See table below .
3 ) When mounted with a U S B interface <At Ex-factory: All are turned ON.> DIPSW1 Function ON OFF DIPSW1-1 Emulation See table below *3 DIPSW1-2 Emulation See table below *3 DIPSW1-3 (Reserved:.
Testing – Printing a Printer Self-Test Page The TUP900, like all Star printers, has a built-in di agnosis printout that can be manually printed to check the printer’s current configuration. This “Self- Test” page also allows the us er to confirm that the printer is in fact operating properly.
24 Star Micronics America, Inc., 1150 King Georges Post Rd, Edison, NJ 088371 Date: 12/3/2007 Example of Self-Test:.
25 Star Micronics America, Inc., 1150 King Georges Post Rd, Edison, NJ 088371 Date: 12/3/2007 Recommended Settings:.
2 6 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883714 Date: 12/3/2007 Specifications.
BASIC SPECIFICATIONS Printing Specifications (1) Print Method: Direct Thermal Line Printing (2) Dot Configuration: 832 dots/line (3) Dot Density: 8 dots/mm (203 DPI) (4) Printing Region: Maximum 104 mm (See figure below) Notes 1) The mechanism can handl e paper widths of 79.
2 8 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883715 Date: 12/3/2007 Maintenance.
P îë P ïïò Ó ß×ÒÌÛ ÒßÒÝÛ Ð»®º±®³ ¬¸» º ±´´±©·²¹ ³¿·²¬»²¿²½» °» ®·±¼·½¿´´§ò Ó¿·²¬»²¿²½» л®·±¼-æ Ûª»®§ - ·¨ ³±²¬.
Left View Rig ht View Front View 30 Star Micronics America, Inc., 1150 King Georges Post Rd, Edison, NJ 088371 Date: 12/3/2007.
3 1 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883716 Date: 12/3/2007 If the green knob on the side of the presenter (in the .
Status Monitor Setup 3 2 Star Micronics America, Inc., 1150 King Georges Post Rd, Edison, NJ 0883721 Date: 12/3/2007.
3 3 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883717 Date: 12/3/2007 STATUS SETUP Please refer to the following instructions for a step by step guide on how to configure and use the Status function.
3 4 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883718 Date: 12/3/2007 Extract the files for a manual install • Connect the printer and follow the prompts to allow the printer driver to install.
3 5 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883719 Date: 12/3/2007 Recommended settings: It’s recommended that yo u enable the Loop HOLD eject setting .
3 6 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883720 Date: 12/3/200 7 The printer will eject or retract depend ing on the memory switch setting. A complete list of Presenter commands are at the end of this document.
3 7 Star Micronics America, Inc., 11 50 King Georges Post Rd, Edison, NJ 0883721 Date: 12/3/2007 You can create errors on the printer such as paper low and .
デバイスStar Micronics TUP992の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Star Micronics TUP992をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStar Micronics TUP992の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Star Micronics TUP992の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Star Micronics TUP992で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Star Micronics TUP992を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStar Micronics TUP992の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Star Micronics TUP992に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStar Micronics TUP992デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
