BarcoメーカーNH-12の使用説明書/サービス説明書
ページ先へ移動 of 35
PMP kit Install ation manual Galaxy NH-1 2, NW-12, G alaxy NW -12 R7649672K R7649676K R59770498/01 28/02/2011.
Barc o nv Simulation D ivision Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.84.86 E-mail: info@barco.com Visit us at the web: www.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ents T ABLE OF C ONTENTS 1 . S a f e t y i n s t r u c t i o n s ...... .... .... ...... .... ...... .... ...... .... ...... .... ...... .... .... ...... .... ...... .... ...... ... 3 1 . 1 S a f e t y d u r i n g k i t i n s t a l l a t i o n .
Tabl e of co nt ents 2 R59770498 PMP KIT 28/02/2011.
1. Safety ins tructions 1. SAFETY INSTRUCTIONS 1.1 Safety during kit installation W ARNING : The pro cedures be low may on ly be per formed b y Barco tr ained a nd quali fi ed technicians. W ARNING : Power down the pr oject or and remove the powe r cord form the wall ou tle t before re moving any of the projector covers.
1. Safety ins tructions 4 R59770498 PMP KIT 28/02/2011.
2. PMP k it 2. PMP KIT 2.1 Introduction Introduction In case of failure of a PMP , it must be replaced by a (blank) new one. However , since mos t of the projector related data is stored on this board, this data will be lost while replacing the board.
2. PMP ki t 6 R59770498 PMP KIT 28/02/2011.
3. Kit ins tal latio n (det ail ed) 3. KIT INST ALLA TION (DET AILED) C AUTION : Thi s procedu re may only be per formed by Bar co trai ned and qual i fi ed technicians. 3.1 Mak ing a backup of the PMP to be replaced Introduction If a PMP fails, communication via Ethernet is most probably still possible.
3. Kit instal lation ( detailed ) 3. L ift the pr eformatter unit a bit and unplug the following connectors: - J100, J101, J102 on the preformatter: data from the PM P - J1 1 on the preformatter: power supply from the power box - J410 on the PMP : commands from the local keypad - J13 on the PMP: commands from the I R receiver 4.
3. Kit ins tal latio n (det ail ed) How to remove the PMP? 1. R emove the input module (see concerning chapter) 2. R emove both screws fi xing the PMP to the front plate Image 3-4 PMP: front fi xing screws 3. R emove the side screws fi xing the input boards to the PMP Image 3-5 4.
3. Kit instal lation ( detailed ) Image 3-7 PMP: fi xing screws of the L VDS interface 6. R emove the screws fi xing the PMP fan assembly to the PMP Image 3-8 PMP fan assembly: fi xing screws (1) Image 3-9 PMP fan assembly: fi xing scr ews (2) 3.2.
3. Kit ins tal latio n (det ail ed) Image 3-12 PMP: fi xing screws of the L VDS interface 3. C onnect the PMP to the inputs by plugging in the board-to-board connectors Image 3-13 PMP: plug int o the input board con nectors 4. F ix the PMP to the input boards using the side screws Image 3-14 PMP: side screws fi xing the input boa rds 5.
3. Kit instal lation ( detailed ) Image 3-15 PMP: front fi xing screws 6. ins tall the input module into the projector (see concerning chapter) 3.2.4 Installing the input module Necessary t ools T orx s crewd river T10 How to install the input module? 1.
3. Kit ins tal latio n (det ail ed) Image 3-17 input m odule: fi xing front screws 4. P ut the preformatter unit next to its correct position and pl ug in the connectors: - J100, J101, J102 on the pr.
3. Kit instal lation ( detailed ) Necessary t ools Computer or laptop, connected to the pr ojector through Ethernet How to upgrade the p rojector software? 1. E nter the correct Ethernet sett ings in the OSD of the projector 2. D ownload the desired upgrade tool to your computer or laptop 3.
A. Backu p and restor e data A. BACKUP AND RESTORE DA T A Overview • Connecting to the projector through Projector Support • Ma king a backup of the projector ’s key data • Restoring a set of k ey data About this chapter It i s extremely important to make backups of your project or data after each sett ing change.
A. Backup and re stor e data Image A-1 Projec tor Support tool: user interface 4. In the Communic ation Parameters section, enter the IP address or the hostnam e of the projector Image A-2 Proje ctor .
A. Backu p and restor e data Tip : Y ou can also press the Query butt on. A list appears, showing all the projectors that are connected to the same network.
A. Backup and re stor e data Select it and hit OK to open a new window where the network setti ngs can be m anually changed. It is advised to switch DHCP to On to continue. Image A-6 Projec tor Suppor t tool : change DHCP sett ing to O N Image A-7 Proje ctor Support to ol: con fi rm ne two rk se tting s A.
A. Backu p and restor e data Image A-8 Projec tor Support t ool: sele ct browse in the Backup section 2. Select a target folder on the computer to save the backup of the projector data Image A-9 Projec tor Support tool: browse to the backup fol der 3.
A. Backup and re stor e data Image A-1 1 Proje ctor Support tool : start th e backup of all settings 5. Wait for the backup pro cess to be fi nished. Image A-12 Proje ctor Support tool: progr ess bar A successful backup i s indicated by a green oval.
A. Backu p and restor e data C AUTION : I t is not allowed t o do any manua l chang e to a bac kup fi le. A changed fi le cannot be rest ored! A.3 Restoring a set of key data C AUTION : If a backup .
A. Backup and re stor e data Image A-15 Projec tor Support tool: browse to the backup fol der 4. In the Res to r e section, you can select an option (not requir ed): - Overwrite serial number - Ov erwrite device typ e Image A-16 5. In the Restore section, hit A ll settin gs Image A-17 Proje ctor Support tool : start th e restore of the backup 6.
A. Backu p and restor e data Image A-18 Projec tor Support tool : con fi rm the restore of the backup 7. Wait for the res tore process to be fi nished Image A-19 Projector Support t ool: progr ess bar Image A-20 Projector Suppo rt tool: reboot of the PMP after the restore A successful restore of the ba ckup fi le is indicated by a gree n oval.
A. Backup and re stor e data Image A-21 Proje ctor Support t ool: restore of the ba ckup was successf ul An error during the restore of the backup fi le is indicated by a brief description and a red oval.
A. Backu p and restor e data Image A-22 Proje ctor Support T ool: restor e of the backup was not s uccessful H o wt or e s t o r et h ek e yd a t ai nan e wP M P ? It is assumed that an or iginal backup fi le is available (zip format).
A. Backup and re stor e data Image A-23 Projec tor Support tool: query list Tip : If more then one PMP without serial number is listed, the MAC address must b e checked. O n the PMP board a label mentioning the MAC address can be found near the power connector on the same side as the heatsinks.
A. Backu p and restor e data Image A-24 Proje ctor Support tool: hit browse in th e restore sec tion 4. B rowse to the fol der on the computer where the backup fi le is stored 5. S elect the backup fi le and hit Open 6. In the Restore section, hit A ll settin gs Image A-25 Projec tor Support tool: browse to the backup fol der 7.
A. Backup and re stor e data Image A-26 Projec tor Support too l: overview of the fi les that will be restore d 8. Wait for the res tore process to be fi nished Image A-27 Projector Support t ool: p.
A. Backu p and restor e data A successful restore of the backup fi le is indicated by a green oval, and t he original serial nu mber will be dis played in the Projector identi fi cation section of the user interface. Image A-29 An error during the r estore of the backup fi le is indicated by a brief descript ion and a red oval.
A. Backup and re stor e data 30 R59770498 PMP KIT 28/02/2011.
Index INDEX B backup 7, 15, 18 making of 18 PMP 7 D description 5 kit 5 I input module 7, 12 installing 12 remo ving 7 installation 5, 7 kit 5, 7 installing 1 0, 12 input module 12 PMP 10 introduction.
デバイスBarco NH-12の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Barco NH-12をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBarco NH-12の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Barco NH-12の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Barco NH-12で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Barco NH-12を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBarco NH-12の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Barco NH-12に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBarco NH-12デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。