Studio RTAメーカーComponent Speakerの使用説明書/サービス説明書
ページ先へ移動 of 15
COMPONENT SPEAKERS AND CROSSOVERS COMPONENT SPEAKERS AND CROSSOVERS CONTENTS (Click on a topic to view) Congratulations N T - 1 T weeter Mounting Introduction Installation StudioDriver N T - 1 Install.
Congratulations Thank you for selecting STUDIODRIVER components. Manufactured in Stuttgart, Germany , technical innovations and high-tech processes are employed throughout our manufacturing process to help ensure many years of musical enjoyment.
Y our new STUDIODRIVER component set is part of an exciting line of loudspeakers. They are the definitive result of years of research and development, realized by the same engineering team charged wit.
2 STUDIODRIVER N T - 1 MOUNTING P ARAMETERS Mounting Hole for Recess Mount 2.125” Mounting Depth .675” - 1.1” T weeter Diameter 1.775” DESCRIPTION One Inch T itanium Dome T weeter Recommended frequency range 4 kHz - 22 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 1600 Hz Re 3.
3 STUDIODRIVER MR-44 DESCRIPTION Four Inch Aluminum Cone Midwoofer Recommended frequency range 160 Hz - 8 kHz MECHANICAL P ARAMETERS Normal Power Handling 50W rms Fs 78.0 Hz Qms 2.74 V as 2.5 Liters Cms 0.78 mm/N Mms 5.3 grams Rms 0.950 kg/sec Xmax 5 mm Sd 48.
DESCRIPTION Five and one quarter Inch Aluminum Cone Midwoofer Recommended frequency range 90 Hz - 3.5 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 62.0 Hz Qms 4.450 V as 6.9 Liters Cms 0.8 mm/N Mms 8.4 grams Rms 0.73 kg/sec Xmax 5 mm Sd 78.
DESCRIPTION Six and one half Inch Aluminum Cone Midbass Recommended frequency range 70 Hz - 3.5 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 57.0 Hz Qms 4.130 V as 18.6 Liters Cms 0.730 mm/N Mms 18.8 grams Rms 0.93 kg/sec Xmax 5 mm Sd 135.
6 N T - 1 TWEETER ASSEMBL Y The tweeters are equipped with wires and attached connectors. The tweeter wires are designated solid black (-), and black with a white stripe (+). Locate the corresponding spade connectors from the hardware pack and crimp them to the end of your chosen speaker wire.
Configuring the NT -1 T weeter Choose the desired method of mounting the tweeters. The NT -1 tweeters can be surface or recess mounted while allowing rotation of the tweeter within the mount for optimal imaging. Surface Mounting Locate the disk designated "E" in the tweeter assembly drawing.
INST ALLA TION Mounting Considerations for your Midwoofers STUDIODRIVER component speakers are designed to mount into most factory speaker locations with minimum effort. The speaker baskets are designed to be a universal fit. When designing your system, a good rule of thumb is to mount the tweeter close to the midrange/midbass speaker .
INST ALLA TION Speaker W iring Locate the hardware pack supplied with your new component set. Inside you will find screws and crimp terminals. The midrange and midbass speakers are each equipped with a small and a large terminal. The large terminal is the positive (+) connection and the small terminal is the negative (-) connection.
10 FN-3 CROSSOVER FN-3 2wayCrossover INPUT WOOFER TWEETER + -- -2dB + 0dB - Connect to the amplifier (+) POSITIVE speaker output Connect to the amplifier (-) NEGA TIVE speaker output Connect to the Mi.
11 FN-6 CROSSOVER FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - W oofer Midrange T weeter + Connect to the amplifier (+) POSITIVE speaker output Connect to the amplifier (-) NEGA TIVE speaker output C.
ADDITIONAL INFORMA TION NO TE: Abuse and/or Installation Error: STUDIODRIVER defines abuse as, but not limited to, burnt voice coils (blackened, no continuity , melted adhesives, coil separated from the former , etc.
Three-Y ear Limited U.S.A. Warranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. StudioDriver warrants its products to be free from.
デバイスStudio RTA Component Speakerの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Studio RTA Component Speakerをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStudio RTA Component Speakerの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Studio RTA Component Speakerの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Studio RTA Component Speakerで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Studio RTA Component Speakerを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStudio RTA Component Speakerの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Studio RTA Component Speakerに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStudio RTA Component Speakerデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
