BarcoメーカーR9001190の使用説明書/サービス説明書
ページ先へ移動 of 48
BARCO PROJECTION SYSTEMS Date : 110797 OWNER'S MANUAL R9001 190 DA T A 3200 Art. No. : R5975398.
Federal communication commission (FCC statement) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
i-1 Table of Contents 5975398 BARCODATA 3200 110797 TABLE OF CONTENTS i TABLE OF CONTENTS .................................................................................................................................................................
i-2 Table of Contents 5975398 BARCODATA 3200 110797 Lock ............................................................................................................................................................................................... 7-8 Fade .
1-1 Unpacking & Dimensions 5975398 BARCODATA 3200 110797 P u l l T o o p e n 1 2 3 4 5 3 7 9 1 UNP ACKING & DIMENSIONS Unpacking To open the banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and remove the foam rubber corners and place the projector on a table.
1-2 Unpacking & Dimensions 5975398 BARCODATA 3200 110797 310a.DRW Battery installation in the RCU. A battery is delivered inside the plastic bag with the power cord. Before using the RCU, first install the battery. Remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU.
2-1 Installation Guidelines 5975398 BARCODATA 3200 110797 2 INST ALLA TION GUIDELINES Installation guidelines Careful consideration of things as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.
2-2 Installation Guidelines 5975398 BARCODATA 3200 110797 * Where to install the projector? Definitions of the Abbreviation on drawings B = Distance between ceiling and top of the screen or between floor and bottom of the screen. A = Correction value, distance between bottom side of projector (without feed) and middle of the lens.
3-1 Location and Functions of Control 5975398 BARCODATA 3200 110797 3 Remote : Remote input for wired remote control. Loudspeaker : for use in small areas only. IR-Acknowledged : IR signals are recognized (green led). IR-Received : IR signals are received but not recognized by the projector (red led).
3-2 Location and Functions of Control 5975398 BARCODATA 3200 110797 CO LOR P HA S E S HA R PN TIN T B R IG H TN STANDB Y E N TE R TE X T E XI T P AU S E - + - + - + - + - + 0 9 7 8 6 5 4 3 2 1 - + - + - + - + - + Control Panel Terminology a. Local keypad Gaining access The keypad is located behind a door, screened with the name of the projector.
3-3 Location and Functions of Control 5975398 BARCODATA 3200 110797 11 12 13 14 Terminology Back light key : When activated, all keys will be lighted up and visible in the dark. ADJ. : ADJUST key, to enter the adjustment mode or for quick exit in the adjustment mode.
4-1 Connections 5975398 BARCODATA 3200 110797 4 A D J E X IT S T B Y T E X T B R IG H T N E S S - + - + - + - + S H A R P N E S S - + T IN T C O L O R C O N T R A S T 0 9 7 8 6 5 4 3 2 1 - + Projector.
4-2 Connections 5975398 BARCODATA 3200 110797 Input connections. The projector has modular input facilities. The input slots can be filled up with the following modules : When the total run time of the lamp is 720 hours or more, the following message will be displayed for 1 minute.
4-3 Connections 5975398 BARCODATA 3200 110797 S - V I D E O 9 8 2 7 9 0 0 V I D E O L R A U D I O O n O n Video input Audio input for S-Video S-Video input Select with or then <ENTER> <EXIT> to return. Select with or then <ENTER> <EXIT> to return.
4-4 Connections 5975398 BARCODATA 3200 110797 R G B H / C V O n 9 8 2 7 9 1 0 S-V IDE O 98 27 900 VID EO L R AU DIO On O n R G B H / C V On 98 27 91 0 R- Y Y B- Y S On 98 279 30 RGB analog input module.
4-5 Connections 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Select with or then <ENTER> <EXIT> to return.
4-6 Connections 5975398 BARCODATA 3200 110797 R G B H / C V O n 9 8 2 7 9 2 0 Floating Non-Float ing A u d i o a m p l i f i e r V C R S - V H S S- VID EO 98 2 7 90 0 VI DE O L R A U D IO O n On Audio Audio to amplifi er R- Y Y B- Y S On 98 2 7 93 0 R G B H / C V On 9 8 2 79 20 Vert.
4-7 Connections 5975398 BARCODATA 3200 110797 Floating Non-Floating S- VI DE O 98 2 7 90 0 V I D E O L R AU D IO On O n R- Y Y B- Y S O n 98 2 79 30 R G B H / C V O n 98 2 79 20 Straps on module level : Floating or non-floating input.
4-8 Connections 5975398 BARCODATA 3200 110797 Connecting a RCVDS 05 to the projector. - Up to 20 inputs with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module. - Serial communication with the projector. - Remote control buttons on the RCVDS to control the projector (source selection and analog settings).
5-1 Controlling 5975398 BARCODATA 3200 110797 5 CONTROLLING C e i li n g S c re e n I R s e n s o r R C U A D D R A DJ E XI T S T BY M U TE TE XT - + - + - + - + - + TIN T R C U F r o n t o f p r o j .
5-2 Controlling 5975398 BARCODATA 3200 110797 0 127 0 60 How to display a projector address? Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds.
5-3 Controlling 5975398 BARCODATA 3200 110797 Volume Control Volume control adjusts the volume. Use the + button for a higher volume. Use the - button for a lower volume. Bass Control Bass control adjusts the bass level (low tones). Use the + button for more low tones.
6-1 Start up of the Adjustment Mode 5975398 BARCODATA 3200 110797 6 ST ART UP OF THE ADJUSTMENT MODE Adjustment Mode All source set ups, picture tunings and geometry are made while in the 'Adjustment mode'. Press the ADJUST or ENTER key to enter the 'Adjustment mode'.
7-1 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 RANDOM ACCESS ADJUSTMENT MODE Starting up the Random Access Adjustment Mode Push the control disk up or down to highlight 'Random Access' and then press ENTER .
7-2 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Select with or then <ENTER> <EXIT> to return. Before using a new source, a correct file has to be installed. The projector's memory contains a list of files corresponding to the most used sources.
7-3 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Edit file The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data.
7-4 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or <ENTER> to toggle or to change value <EXIT> to return Syn c pu lse Clamp pulse Clamp delay Clamp width Exampl.
7-5 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 The first character is highlighted. Push the control disk to the right or to the left to select the desired character. Change that character by pushing the control disk up or down. Numeric characters can be entered directly with numeric keys on the RCU.
7-6 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Delete File To delete a selected file out of the list of files. Use the control disk to select DELETE and press ENTER . The delete selection menu will be displayed.
7-7 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. 0 2.5 1 2.4 Sync slow/fast Highlight sync by pushing the control disk up or down and press ENTER to toggle between SLOW and FAST.
7-8 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Audio Tuning Highlight Audio Tuning by pushing the control disk up or down and press ENTER to select.
7-9 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Geometry Highlight Geometry by pushing the control disk up or down and press ENTER to select the geometry selection menu. The following adjustment are possible : - horizontal and vertical image shift.
7-10 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Side keystone Highlight Side Keystone by pushing the control disk up or down and press ENTER to select. The side keystone adjustment is used to align the image if the projector is mounted as a non standard projection angle.
7-11 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 720 pixels 480 pixels Scale [1:1 ] Scale [1:x] Adjustment of the blanking on the top of the image Adjustment of the blanking on the bot.
7-12 Random Access Adjustment Mode 5975398 BARCODATA 3200 110797 Options Highlight Options by pushing the control disk up or down and press ENTER. The Geometry Options menu will be displayed. The next question will be asked by the projector : 'Use the same side keystone correction for all files ? [YES] or [NO].
8-1 Installation Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. 8 Internal Patterns The projector is equipped with different internal patterns which can be used for measurment purposes.
8-2 Installation Mode 5975398 BARCODATA 3200 110797 -0,5 -0,2 5 0 0, 25 0,5 12345 6 80 120 160 200 240 40 30 15 -1,5 -1 -0,5 0 0, 5 1 1, 5 123456 80 120 160 200 240 40 90 60 30 Screen Width Horizontal.
9-1 Service Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. 9 SERVICE MODE Starting up the Service Mode Push the control disk up or up to highlight Service and then press ENTER . Some items in the Service mode are password protected (when the password function is active).
9-2 Service Mode 5975398 BARCODATA 3200 110797 PANEL ADJUSTMENT RED COARSE FIELD FLICKER BLACK LEVEL TOP BLACK LEVEL BOTTOM GAIN TOP GAIN BOTTOM Change color+pattern with or Select with or then <ENTER> <EXIT> to return.
9-3 Service Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Select with or then <ENTER> <EXIT> to return.
9-4 Service Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. Select with or then <ENTER> <EXIT> to return. Reset Lamp Runtime Reset lamp run time is only allowed when a new lamp is installed. Highlight Reset Lamp Run Time by pushing the control disk up or up and press ENTER to select.
9-5 Service Mode 5975398 BARCODATA 3200 110797 Select with or then <ENTER> <EXIT> to return. I2C DIAGNOSIS D CA LCD DRIVER SC76013 E6H # # # LCD DRIVER SC76013 E8H # # # LCD DRIVER SC76013.
A-1 Appendix A : Standard Source Set Up Files 5975398 BARCODATA 3200 110797 A ST ANDARD SOURCE SET UP FILES Name : name of file, contains the settings Resolution : image resolution, when fol- lowed by ...I means interlaced. FVERT Hz : vertical frequency of the source FHOR kHz : horizontal frequency of the source.
A-2 Appendix A : Standard Source Set Up Files 5975398 BARCODATA 3200 110797 NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT Hz kHz MHz XGA_70 1024 X 768 70,000 57,050 78,044 1368 1024 815 768 MAC_POR 640 X 870 74,996 68,846 57,280 832 640 918 870 INTER_GR 1184 X 886 67,170 61,796 92,941 1504 1184 920 886 SG_60_2 1024 X 768 60,000 48.
B-1 Lenses 5975398 BARCODATA 3200 110797 B Focusing the lens Loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right. Attention : Do not turn out the lens too far, otherwise it will fall out of the lens holder.
B-2 Lenses 5975398 BARCODATA 3200 110797 Lenses This APPENDIX gives an overview of the tables and formulas for the available lenses for the BARCOGRAPHICS 9200. An overview of all tables, diagrams and formulas can also be found in the manual "Installation diagrams for BARCO projectors", order number : R5975924.
C-1 Source Numbers 90 - 99 5975398 BARCODATA 3200 110797 C Follow the steps below to create a second file for sources 0 to 9 : 1. Select the source between 0 and 9. 2. Select the corresponding source number between 90 and 99 with the digit keys on the RCU.
Insert Card RCU 5975398 BARCODATA 3200 110797 " INSERT CARD 3.
デバイスBarco R9001190の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Barco R9001190をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBarco R9001190の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Barco R9001190の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Barco R9001190で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Barco R9001190を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBarco R9001190の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Barco R9001190に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBarco R9001190デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。