BarcoメーカーR9002031の使用説明書/サービス説明書
ページ先へ移動 of 57
R9002031 R9002038 OWNER'S MANUAL DA T A 808s.
.
BARCO PROJECTION SYSTEMS Date : 170397 Art. No. : R5975597 R9002031 R9002038 OWNER'S MANUAL DA T A 808s.
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, March 1997. All rights reserved. Trademarks are the rights of their respective owners.
Table of Contents i-1 5975597 BARCODATA 808S 110397 Table of contents ........................................................................................................................................................................... i Safety instructions .
Table of Contents i-2 5975597 BARCODATA 808S 110397 Blanking Adjustments ........................................................................................................... ............................................. 6-15 Convergence Adjustment .
Safety Instructions 1-1 5975597 BARCODATA 808S 170397 WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Instructions 1-2 5975597 BARCODATA 808S 170397 A. Mains lead (Power cord) with CEE 7 plug : The wires of the mains lead are colored in accordance with the following code. Green and yellow: earth (safety earth) Blue: neutral Brown: line (live) B.
Location and Functions of Control 2-1 5975597 BARCODATA 808S 110397 2 LOCA TION AND FUNCTION OF CONTROLS REAR PANEL TERMINOLOGY PORT 4/5 See installation instructions before connecting to t he supply. Vo ir la n oti ce d 'i nstal la t i on a van t de r acco rde r a u résea u.
Location and Functions of Control 2-2 5975597 BARCODATA 808S 110397 Control panel terminology GRAPHICS a. The Local Keypad Gaining Access The local keypad is located underneath the top cover door with the BARCO logo. To open this door, push as indicated on drawing and turn it to the front side of the projector.
Connections 3-1 5975597 BARCODATA 808S 110397 3 CONNECTIONS PORT 4 /5 See install ation inst ruct ions b efore c onnecti ng t o t he sup ply. Voir la n otice d'inst allatio n avant de racco rder au r é seau. 120/230 V 7/5 Amp 50/6 0 Hz 75 Ohm PORT 2 75 Ohm This d evice compli e s w it h part 15 of th e F CC ru le s.
Connections 3-2 5975597 BARCODATA 808S 110397 PROJECT OR WARM UP A FULL WHITE PATTERN WI LL BE GENE RATED FO R 20 MIN UTES. FOR IMMEDIATE USE OF THE PROJEC T OR, PRESS <EXIT>. WA RNI NG : SKIP PI NG THIS PRO C EDUR E CA N RE DUC E THE I NITIAL P ICTURE QUALITY OF THE PROJECTED IMAGE.
Connections 3-3 5975597 BARCODATA 808S 110397 Connecting a Composite Video source to port 1. Composite video signals from a VCR, OFF air signal decoder, etc.. PORT 4/5 See install a tion instructions b e fore connecting to the supply . Voir la notice d'install ation avant de raccorder au r é s eau.
Connections 3-4 5975597 BARCODATA 808S 110397 Connecting a RGB Analog source to port 3. Connect your RGB source via an interface to Port 3. Always use an interface when a computer and local monitor have to be connected to the projector.
Connections 3-5 5975597 BARCODATA 808S 110397 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) RGB analog input terminals with Tri level sync input or Tri- level sync on green. The projector detects automatically where the sync signal is located.
Connections 3-6 5975597 BARCODATA 808S 110397 PERIPHERAL EQUIPMENT Connecting a RCVDS 05 switcher to the BARCODATA 808S - Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules. - Serial communication with the projector.
Controlling 4-1 5975597 BARCODATA 808S 110397 4 CONTROLLING Caution : Do not display a stationary image with full brightness and contrast for longer than 20 min.
Controlling 4-2 5975597 BARCODATA 808S 110397 The projector can be controlled with a. The RCU b. The hardwired RCU (cable not included) c. The built-in RCU (local keypad) The procedure and results of controlling the projector with either of these RCU options is essentially the same.
Controlling 4-3 5975597 BARCODATA 808S 110397 Port No Projector input Press Digit Button 1 Comp. Video 1 2 S-Video 1 /Comp. Video* 2 3 RGB 2 3 4/5 RGB 2 4 or 5 4/5 Component video 3 6 4/5 RGB with Tri.
Controlling 4-4 5975597 BARCODATA 808S 110397 Analog Picture Controls The analog picture controls can be adjusted with the RCU. The control keys are located on the lower right side of the key panel of the RCU and indicated with the name of the control and an icon.
Start Up of the Adjustment Mode 5-1 5975597 BARCODATA 808S 110397 5 ST ART UP OF THE ADJUSTMENT MODE Adjustment Mode All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Press the ADJUST key to enter the 'adjustment mode'.
Start Up of the Adjustment Mode 5-2 5975597 BARCODATA 808S 110397 Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (Password protection is only available when the password DIP switch on the controller module is in the ON position.
Random Access Adjustment Mode 6-1 5975597 BARCODATA 808S 110397 6 RANDOM ACCESS ADJUSTMENT MODE Starting-Up the Random Access Adjustment mode. Push the control disk up or down to highlight "RANDOM ACCESS" and then press ENTER . Some items in the Random access mode are password protected (when the password function is enabled).
Random Access Adjustment Mode 6-2 5975597 BARCODATA 808S 110397 RANDOM ACCESS ADJUSTMENT MODE CONVERGENCE H SIZE V SIZE BLANKING LEFT BOTTOM RIGHT TOP V LINEARITY GREEN ONLY BLUE ON GREEN RED ON GREEN.
Random Access Adjustment Mode 6-3 5975597 BARCODATA 808S 110397 Selecting Setup Pattern If an external source is connected to the projector, this menu will be displayed. Push the control stick forward or backward to highlight the desired setup pattern and then press ENTER .
Random Access Adjustment Mode 6-4 5975597 BARCODATA 808S 110397 Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT ORBITING CONTR. MODULATION SOFT EDGE Select with or <ENTER> to accept <EXIT> to return.
Random Access Adjustment Mode 6-5 5975597 BARCODATA 808S 110397 Sync Fast/Slow Adjustment The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image. Highlight SYNC by pushing the control disk up or down and press ENTER to toggle between FAST and SLOW .
Random Access Adjustment Mode 6-6 5975597 BARCODATA 808S 110397 Port 2 : Video or S-Video Port 2 can be used as a Video or S-Video input. Highlight Port 2 by pushing the control disk up or down and press ENTER to toggle between VIDEO and S-VIDEO. Select with or <ENTER> to accept <EXIT> to return.
Random Access Adjustment Mode 6-7 5975597 BARCODATA 808S 110397 Focusing Before starting the 'focusing' adjustment, be sure the lenses are correctly focused. Push the control disk up or down to select 'Focusing' and press ENTER . Select with or then <ENTER> <EXIT> to return.
Random Access Adjustment Mode 6-8 5975597 BARCODATA 808S 110397 Geometry Adjustments The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented f.
Random Access Adjustment Mode 6-9 5975597 BARCODATA 808S 110397 Raster Shift Adjustment The green raster must be centered both horizontally and vertically on the center of the CRT surface. To center the green raster, look into the green lens and use the control disk to move the raster.
Random Access Adjustment Mode 6-10 5975597 BARCODATA 808S 110397 Left-Right (east-west) Adjustments Left-right adjustments affect only the vertical lines of the projected image. Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in the same manner.
Random Access Adjustment Mode 6-11 5975597 BARCODATA 808S 110397 Seagull correction Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a 'S' deformation is visible on the left and the right side of the image.
Random Access Adjustment Mode 6-12 5975597 BARCODATA 808S 110397 Top-Bottom (north-south) Adjustments Top-Bottom and center adjustments affect only the horizontal lines of the projected image.
Random Access Adjustment Mode 6-13 5975597 BARCODATA 808S 110397 Seagull Correction Use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull) on top and bottom of the image is visible, proceed to the seagull correction.
Random Access Adjustment Mode 6-14 5975597 BARCODATA 808S 110397 Vertical Linearity Adjustment The vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image.
Random Access Adjustment Mode 6-15 5975597 BARCODATA 808S 110397 Blanking Adjustments Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise).
Random Access Adjustment Mode 6-16 5975597 BARCODATA 808S 110397 Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT ORBITING CONTR.
Service Mode 7-1 5975597 BARCODATA 808s 110397 Starting up the Service mode. Use the control disk to highlight 'Service' and then press ENTER . Some items in the Service mode are password protected (when the password function is active). Enter your password to continue.
Service Mode 7-2 5975597 BARCODATA 808s 110397 Identification Highlight 'Identification' with the control disk and press ENTER . The 'Identification' screen gives information concerning : - Projector address. To change the address of your projector, contact a qualified service technician.
Service Mode 7-3 5975597 BARCODATA 808s 110397 Deletion of blocks This item is password protected. The delete function is used to clear all data (settings) from an adjustment block. A delete can be given : - block by block or - for all blocks. Deleting block by block The delete a block function deletes the settings of a selected block.
Service Mode 7-4 5975597 BARCODATA 808s 110397 Change password This item is password protected. Highlight 'change password' with the control disk and press ENTER . The current password is displayed. The new password must consist of 4 digits between 0 and 9.
Service Mode 7-5 5975597 BARCODATA 808s 110397 Set to midposition Item is password protected. Highlight 'set to midposition' with the control disk and press ENTER to set all settings to their midposition. A confirmation menu will be displayed first.
Service Mode 7-6 5975597 BARCODATA 808s 110397 When undo is pressed all convergence settings are reset to the previous settings. Dynamic Astigmatism (spot shape adjustment) The spot shape adjustments correct the spot shape in 8 different areas on the screen and that for the three colors separately.
Service Mode 7-7 5975597 BARCODATA 808s 110397 Push the control disk up or down for diagonal astigmatism adjust- ment and to the left and to the right for axial astigmatism adjustment. Press ENTER to continue selecting a new area. The adjustment direction (axial or diagonal) and adjustment value are given in a text box on the screen.
Service Mode 7-8 5975597 BARCODATA 808s 110397 Projector Warm Up Highlight 'Projector Warm Up' by pushing the control disk up or down and press ENTER to select the projector warm up menu. Select with or then <ENTER> <EXIT> to return.
Messages, warnings and failure codes 8-1 5975597 BARCODATA 808s 110397 8 MESSAGES, W ARNINGS AND F AILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz Announcement of the selected source. enter password xxxx Message to enter your password.
Messages, warnings and failure codes 8-2 5975597 BARCODATA 808s 110397 WARNING : go to stand by Projector will switch to 'stand-by' when the RCVDS is no longer available. WARNING : invalid frequency input The entered frequency or ap- plied frequency of the source is out of the projector's range.
Options 9-1 5975597 BARCODATA 808s 110397 IR Receiver 800 This infrared receiver unit makes it possible to control the projector from another room. There is a communication line with cable between the IR receiver and the projector or the RCVDS05. The control information from the RCU can now be sent to this IR receiver.
Options 9-2 5975597 BARCODATA 808s 110397 MAGIK Interface Multifuctional Analog Graphics Interface Kit. BARCO's MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display.
Orbiting A-1 5975597 BARCODATA 808s 110397 A ORBITING Orbiting (option) Static pictures are very often shown on large screen projectors, espectially in process control and presentation applications.
Orbiting A-2 5975597 BARCODATA 808s 110397 Orbiting Speed Toggle (only in MASTER Orbiting) Highlight 'SPEED : SLOW' with the control disk and press ENTER to set the ORBITING SPEED to Fast. Highlight 'SPEED : FAST' with the control disk and press ENTER to set the ORBITING SPEED to Slow.
Orbiting A-3 5975597 BARCODATA 808s 110397 Adjustment procedure multiple projector installations : Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum.
Orbiting A-4 5975597 BARCODATA 808s 110397.
Adjustment Blocks and Source Numbers 90-99 B-1 5975597 BARCODATA 808s 110397 Adjustment Blocks (memory blocks) As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector ’ s memory as numeric values.
Adjustment Blocks and Source Numbers 90-99 B-2 5975597 BARCODATA 808s 110397 The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector).
Insert Card i-1 5975597 BARCODATA 808s 110397 P RCU INP UT S OURCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INP UT S OURCE S 7 P RCU INP UT S OURCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 .
デバイスBarco R9002031の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Barco R9002031をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBarco R9002031の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Barco R9002031の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Barco R9002031で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Barco R9002031を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBarco R9002031の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Barco R9002031に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBarco R9002031デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。