SweexメーカーLW161の使用説明書/サービス説明書
ページ先へ移動 of 34
3.
4 L W160/L W161 Sweex Wireless 150N Router • Do not expose the Sweex Wireless 150N Router to extreme temperatures. Do not place the device in direct sunlight or in the direct vicinity of heating elements. • Do not use the Sweex Wireless 150N Router in extremely moist or dusty surroundings.
5 English version Product description Front 1. Power LED: This light indicates that the router receives power. 2. READY LED: A constantly blinking SYS light indicates correct functioning of the router . 3. WPS LED: When this light blinks, it is possible to connect to the router with a WPS enabled device.
6 Back 1. DC power input: Connect the supplied power adapter to this input. If the adapter is lost it can be replaced by a similar model with 9 V DC output and 0.6 A cur rent rating. 2. POWER ON/OFF button: Press the button in to power on the router and press again to turn off the router .
7 English version Simple setup Simple setup is done in 7 steps: 1. Disconnect the power to your modem. If one or more computers were connected to your modem using a network cable, disconnect them. 2. Use the included network cable to connect your modem to the blue WAN port of the router.
8 Connecting to a wireless network • Windows XP: Right click on your wireless adapter’ s icon at the bottom right of your screen and click “View Available W ireless Networks”: A window titled “Choose a wireless network” will appear .
9 Note: If you see a red cross near the network and the text: “The settings saved on this computer for the network do not match the requirements of the network”, please refer to the troubleshooting section of this manual.
10 Windows 7: Windows 7 will indicate when wireless networks are available. Yo u can recognise this by the following icon in the bottom-right of your screen: Note: If you see a small red cross through the icon, no networks are in range of your computer.
11 The following screen will appear, enter the desired name for your wireless network and click “Next” to begin configuring the router: Note: The default security method with this setup procedure is WPA2. If a device in your network does not support WP A2, you can change the security method by clicking the “Advanced” button.
12 Advanced setup Advanced setup can be done when you know exactly which settings your ISP requires or when the simple setup fails. There are 4 possible configurations.
13 Yo u should see the Internet Configuration Wizard screen: Yo u can now proceed with the advanced setup using one of the configurations described further on. Checking if the router is successfully connected to the internet For all configurations, it is possible to check in the router if you have a working internet connection.
14 Configuration 2: PPPoE If your ISP requires the PPPoE connection type, click the “PPPoE” button. Yo u will see the following screen: Enter your account name (user name) that has been provided to you by your ISP in the “User Name” field and the corresponding password in the “Password” field.
15 During all selections you will have an option to configure the “Basic” wireless settings of the router . The following screen is presented during each choice: Fill all fields in as desired. Please view the “Wireless network configuration” section for more infor mation about the options presented.
16 Note: Cloning your MAC address must be done from the computer that was originally connected to your modem, and this computer must be connected to your router by network cable.
17 Mode The type of wireless standard can be chosen here, it is recommended to use the default setting. Channel Width In this section it is possible to manually select the channel width (20/40MHz), it is recommended to keep the default setting.
18 Method 1: WEP Securing your network with WEP is done in 3 steps: 1. Select the following settings: T ype: “Automatic” (it is recommended to use the default setting) WEP Key Format: “Hexadecimal” or “ASCII” Key Selected: Insert the chosen “WEP key” and define the “Key type” 2.
19 After a WPS secured connection has been set up for the first time, all previously connected devices will lose their connection. Yo u will have to connect them using the same WPS method or by manually entering the W PA key as described below.
20 To configure a device for a static DHCP address, fill out the device’ s corresponding MAC address in the “MAC Address” section and fill in the “desired IP in the “Reser ved IP Address”, then click the “Save” button.
21 For a DMZ, click “DMZ” in the menu on the left, enter the IP address of the device, check the “Enable” checkbox and click the “Save” button. Bandwidth Control Bandwidth control is also known as “bandwidth management”. It allows you to artificially restrict bandwidth for one or more devices on your network.
22 English version T roubleshooting This chapter of the manual will explain a number of common issues that you may run into and possible solutions. • I cannot log into my router at http://192.168.16.1/ . Windows indicates that I have a working network connection.
23 English version 3. Right click the first connected LAN or High-Speed Internet Connection, in this example the “Local Area Connection”, and click “Proper ties” from the context menu. If you have multiple connected connections, repeat steps 3 to 6 for each connection.
24 5. The Internet Protocol’s property window appears. In this window , ensure that both settings are set to “Obtain automatically”: 6. Confirm the settings by clicking “OK”. The network settings for XP are now properly configured for your router .
25 2. In the Control Panel, click “View network status and tasks”. If your Control Panel is in classic view , open the “Network and Sharing Center” icon: 3.
26 English version 4. Right click the first connected LAN or High-Speed Internet Connection, in this example the “Local Area Connection”, and click “Proper ties” from the context menu. If you have multiple connected connections, repeat steps 4 to 7 for each connection: 5.
27 English version 6. The Internet Protocol V ersion 4 ’s property window appears. In this window , ensure that both settings are set to “Obtain automatically”: 7. Confirm the settings by clicking “OK”. The network settings for Vista are now properly configured for your router .
28 2. In the Control Panel, click “View network status and tasks”. If your Control Panel is in icon view , open the “Network and Sharing Center” icon: 3.
29 4. Right click the first connected connection, in this example the “Local Area Connection”, and click “Properties” from the context menu. If you have multiple connected connections, repeat steps 4 to 7 for each connection: 5. The connection’s property window appears.
30 6. The Internet Protocol V ersion 4 ’s property window appears. In this window , ensure that both settings are set to “Obtain automatically”: 7. Confirm the settings by clicking “OK”. The network settings for Windows 7 are now properly configured for your router.
31 4. The “LAN Settings” window will now open. Ensure that all checkboxes are unchecked and confir m the settings by clicking “OK” English version.
32 • My computer indicates that it is not connected to a network. • This problem is usually resolved by carefully checking all connections and indicator lights. For a wired computer , follow the network cable to the router’s backside. It must be plugged in to one of the yellow LAN ports.
33 3. The Manage Wireless Networks window now opens. In this window , select the conflicting network and click “Remove”. After the network has been deleted, you can close the window and follow the steps described in the “Connecting to a wireless network” section of the manual.
34 3. In the Network and Sharing Center, click “Manage wireless networks”: 4. The following window will appear , right click the network that was indicated with a red cross in step 2 and click “.
35 5. After the network has been removed, you can close the window and follow the steps described in the “Connecting to a wireless network” section of the manual. • I have lost the W PA or WEP key required to access my wireless network. • There are two possible solutions for this issue: 1.
36 W arranty 2-year standard warranty within the EU • In a standard manner a warranty period of 2 years as from the purchase date is available for this Sweex product within the EU.
デバイスSweex LW161の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sweex LW161をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSweex LW161の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sweex LW161の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sweex LW161で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sweex LW161を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSweex LW161の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sweex LW161に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSweex LW161デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
