SwisherメーカーZT2560の使用説明書/サービス説明書
ページ先へ移動 of 16
REPAIR MANUAL ZT2560 Swisher Mower Co Warrensburg, MO.
TABLE OF CONTENTS 1. If engine won’t crank 2. If engine won’t crank – continued 3. If engine cranks but won’t start If engine stalls when PTO is engaged 4. If PTO clutch will not engage Hour meter not operating 5. Wire identification at switches 6.
IF ENGINE WON’T CRANK ALWAYS CHECK FUSE FIRST TEST #1 Using a remote starter switch or suitable device, make a connection between the large ter minals on the solenoid.
A neutral switch is located on the lower end of bot h drive control handles and is activated when the handles are outward in the neutral position. Check that the plunger buttons on both switches are depressed at least 3/8”. Meter should go to zero when checking continuity across switch terminals with plungers depressed.
ENGINE CRANKS BUT WON’T START Checks for electrical problems • While turning ignition switch to its first position, listen for the fuel solenoid on the carburetor to click. It must click to supply fuel to the carburetor. • Try a new spark plug. • Check for spark at plug when it is re moved and the threaded end is grounded.
IF PTO CLUTCH WILL NOT ENGAGE HOUR METER NOT OPERATING Hour meter has a positive and a negative post. Gray wire should go on the positive. Power is supplied from the ignition switch. Green wire from hour meter is grounded by the oil pressure switch, therefore only has a ground when the engine is running.
WIRE IDENTIFICATION AT SWITCHES 3623 IGNITION SWITCH STARTER SOLENOID Heavy red cable goes to the starter. Red wire goes to ignition switch. Green wire goes to neutral switches and on to the ignition switch. Green wire with orange stripe goes to the ground.
WIRING HARNESS TO EN GINE PLUG CONNECTION Gray wire goes to carburetor fuel solenoid Green wire goes to oil pressure switch Black wire goes to engine ignition module Red wire goes to engine charging system Green wire goes to hour meter Red wire goes to terminal on solenoid with the positive battery cable.
BATTERY CHARGING SYSTEM To test alternator before it goes to the regulator, unplug the yellow connector and measure the AC voltage across the the two gray wires inside this connector.
DRIVE CONTROL ADJUSTMENTS LEFT SIDE SHOWN Control plate shown in neutral position Hydro linkage Start your adjustments by putting the drive control arms in the neutral position. Remove the linkage from the control plate at the Eaton hydro by removing the cotter pin and washer on the under side.
OVERVIEW OF DRIVE CONTROL LINKAGE RIGHT SIDE SHOWN Right side control handle Pivot point for control handle moveme nt Pivot point Adjustment threads on control rod Forward and reverse control on hydro.
PARKING BRAKE AND NEUT RAL SWITCH OPERATION Parking brake cable atta ches here. Right side is shown. Control panel has been removed for better view. Right side drive control handle. Safety switch rocker arm pivots on a bolt at this point. Parking brake is activated by this bolt as the drive control handle is swung outward in the neutral position.
DECK LIFTING SYSTEM Three rocker arms are activated by the deck lift handle. This is the right side control. Note the routing of the cabl e. It drops straight below to the deck.
DECK BELT REPLACEMENT ENGINE TO DECK BELT •Lower the deck to lowest setting •Loosen tension on tension idler •Remove worn or damaged belt •Using part# 10263 belt, route it around the engine pulley as shown in the diagram.
REPAIRING OR REPLACING BLADE DRIVER Torque top nut to 90 ft/lbs Replacing this nut each time is recommended. Pulley does not have a hub. When removing, just lift it off like a washer, no puller is needed. Machine washers are used to keep the pulley from contacting the outer ra ce of the bearing.
For additional assistance on service Contact Swisher Mower Co., Inc. Phone 1-800-222-8183 Fax 1-660-747-3160 E-mail cust.serv@swisherinc.com 14.
デバイスSwisher ZT2560の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Swisher ZT2560をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSwisher ZT2560の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Swisher ZT2560の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Swisher ZT2560で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Swisher ZT2560を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSwisher ZT2560の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Swisher ZT2560に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSwisher ZT2560デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。