TANDBERGメーカーD1392602の使用説明書/サービス説明書
ページ先へ移動 of 33
TANDBERG Video Portal Data port Command In terface User Guide T ANDBERG V ideo Portal Data port Command Interface User Guide Softwar e version V 3 D1392602 TANDBERG D1392602 1.
TANDBERG Video Portal Data port Command In terface User Guide Table of Contents 1. INTRODUCTION .......................................................................................................................... 3 2. CONNECTIN G TO THE DATA PORT COM MAND INTERFACE THROUGH THE RS -232 PORT.
TANDBERG Video Portal Data port Command In terface User Guide 1. Introduction The TANDBERG Video Portal Data port Command Interface User Guide contains guidelines on how to us e the textual command interface supported by the Video Portal sy stem, further referred to as Video Portal.
TANDBERG Video Portal Data port Command In terface User Guide 2. Connecting to the Data port Command Interface through the RS-232 port. The RS-232 port is a 9-pin, fem ale, sub-D connector located on the front of the Video Portal. The port is configured as a DCE (Data Communications Equipment).
TANDBERG Video Portal Data port Command In terface User Guide D1392602 5 If communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should.
TANDBERG Video Portal Data port Command In terface User Guide 3. Connecting to the Data port Co mmand Interface using Telnet The TANDBERG Video Portal has one LAN port. The Video Portal’s Telnet server provides access to th e Data port Command Interface through a 10/100 base T network interface supporting the TCP/IP protocol.
TANDBERG Video Portal Data port Command In terface User Guide 4. The TANDBERG Video Portal Commands 4.1. Introduction Typing ‘ ? ’ or ‘ help ’ when connected to the Data Port Comma nd Interface will return a list of valid commands. The commands are used to control the functions of the Video Portal.
TANDBERG Video Portal Data port Command In terface User Guide • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The command Xconf telnet mode: "on" enables telnet access on the Video Portal.
TANDBERG Video Portal Data port Command In terface User Guide 4.2.1. System Configuration Commands Command: Description: a lplan Mapping o f a call onto a se rvice or anot her call. Dialplan En try [1.. 64] Enable d: <On/Off> Dialplan Entry [1..
TANDBERG Video Portal Data port Command In terface User Guide distingui shed: • Net type - Either H324m, H323 or SIP of the outbound call. • AV mode – Th is mode deter mines the out bound audi o and vide o call settings.
TANDBERG Video Portal Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 1 Prefi x: "207947 13 3" *c xConfigurat ion Dialpl a n Entry 1 Suffix: " " *c xCon.
TANDBERG Video Portal Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Nam e: "avmode" *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Value: &.
TANDBERG Video Portal Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Prefi x: "903700 10" *c xConfigurat ion Dialpl a n Entry 4 Suffix: " " *c xConfi.
TANDBERG Video Portal Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Pro perty 14 Nam e : "entry5 _la bel " *c xConfigurat ion Dialpla n Ent ry 4 Pro pe rt y 1.
TANDBERG Video Portal Data port Command In terface User Guide Xconf H323Gatekeeper Authentication *c xConfigur ation H323Gat ekeeper Authenti cation Addre ss: “abc.
TANDBERG Video Portal Data port Command In terface User Guide • Gateway: Sets the gateway IP address. If a gateway is located on the LAN and the Video Port al needs to reach nodes through this gatew.
TANDBERG Video Portal Data port Command In terface User Guide or SIP Interface T ransport Default: <T CP/UDP/TLS> --- sub-co mmands: • Mode : Specifies whether the system uses a default SIP proxy. • Address: Specifies the IPv4 address or FQDN of the SIP pr oxy.
TANDBERG Video Portal Data port Command In terface User Guide *c xConfigur ation SNMP SystemContact: "" *c xConfigur ation SNMP SystemLocatio n: "" *c xConfigur ati on SN MP HostIPAddr 1: "12 7. 0. 0. 1 " *c xConfigur ati on SN MP HostIPAddr 2: "12 7.
TANDBERG Video Portal Data port Command In terface User Guide 4.2.2. General Video Portal Commands Command: Description: ExternalManager This command sets the path and address of the TMS serv er. A message is sent to TMS when the Video Port al starts up to si gnal TMS that t he Video P ortal is ready.
TANDBERG Video Portal Data port Command In terface User Guide 4.2.3. System Status Commands Command: Description: Dialplan Shows the di alplan co nfiguration.
TANDBERG Video Portal Data port Command In terface User Guide Ethernet Displays the configuration of the Et hernet interface Ethernet Status format: < MacAddress> <Speed> --- Parameters: .
TANDBERG Video Portal Data port Command In terface User Guide Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: &.
TANDBERG Video Portal Data port Command In terface User Guide Name> --- Parameters: • Address , the IP address of the Vide o Portal • SubnetMask , the subnetmask used fo r the connected network • Gateway , the gateway to route traffic to an IP num ber outside the connect ed net w or k • DNS Server [1.
TANDBERG Video Portal Data port Command In terface User Guide Options Parameters: ---- Example of Options feedback: *s Options: Option 1: Key: "115201P1-1-43F072FC" Description: "1 trunk" *s/end Service Displays all co nfigured/upl oaded services.
TANDBERG Video Portal Data port Command In terface User Guide Status format: <ProductType> <Uptime> <Software Version> Name> ReleaseDate> Configuration Telephony:> VideoTele.
TANDBERG Video Portal Data port Command In terface User Guide Configur ation: PRI:41 Temperat ureCelcius: NA Temperat ureFahrenheit: NA *s/end 4.2.4. Debug Commands Command: Desription : Syslog Enables a real- time log of B onding, H.221 and H 324m, ISDN , RTSP, IVi der, and IVide r Engine activi ty.
TANDBERG Video Portal Data port Command In terface User Guide Example: xComm and Boot *r Result (status=OK): / *r/end OK CUIL rebo ot request , restarting CheckDisk This command shows t he presence and th e status of t he internal harddisk.
TANDBERG Video Portal Data port Command In terface User Guide Dial This comm and establishes a dial out to an end point Parameters: • CalledParty: <S:0 , 60> End point to be connected with the service. • CallingParty: <S:0, 60> Service telephone number.
TANDBERG Video Portal Data port Command In terface User Guide Example: xComma nd DisconnectCal l ABCD12 3456 *r Result (status=OK): *r/end OK EraseDisk This command wipes all the data from the internal harddisk Example: xComma nd EraseDisk *r Result (status=OK): *r/end OK FeedbackDeregister Command use d to deregi ster XML feedbac k over HTTP(S) .
TANDBERG Video Portal Data port Command In terface User Guide • Cause: <1…> Cause code s pecifying why the command was not accepted by the system • Description Textual description of t he cause code. Example: xComma nd feedbackregist er url:http: //10.
TANDBERG Video Portal Data port Command In terface User Guide Example (Delete Service nr. 10): xComma nd ServiceEntry Delete 10 *r Result (status=OK): / *r/end OK ServiceEntrySwap Command used to swap service num bers. Parameters: • ServiceEntryNumber(r): < 1.
TANDBERG Video Portal Data port Command In terface User Guide General User Commands About Shows following system information: Software ve rsion: R3.0 Portions of this softwa re are licensed under 3r d pa rty licenses. See th e CD accompanying this product for det ails.
TANDBERG Video Portal Data port Command In terface User Guide D1392602 33 "xfeedback register status/ca ll" - t o monitor call changes "xfeedback register status/call--" - to monit.
デバイスTANDBERG D1392602の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
TANDBERG D1392602をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTANDBERG D1392602の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TANDBERG D1392602の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TANDBERG D1392602で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TANDBERG D1392602を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTANDBERG D1392602の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TANDBERG D1392602に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTANDBERG D1392602デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。