TascamメーカーMD-801R/P Mk IIの使用説明書/サービス説明書
ページ先へ移動 of 52
» M D-801 R @#/ M D-801 P @# MD Recorder/Pla y er O WNER’S MANU AL CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE.
2 –– TASCAM MD-801R/P Mk II Important Safety Precautions IMPOR T ANT (f or U .K. Customers) DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
TASCAM MD-801R/P Mk II –– 3 CA UTION: … Read all of these Instructions. … Save these Instructions f or later use . … Follow all W arnings and Instructions marked on the audio equipment. 1) Read Instructions — All the safety and operating instructions should be read before the product is operated.
4 –– TASCAM MD-801R/P Mk II 1 CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT 2 CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. VORSICHT! UNSICHTBARE LASERSTRAHLUNGTRITT AUS. WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST.
Table of Contents TASCAM MD-801R/P Mk II –i 1 - Introduction 1.1 About the MiniDisc format ................ 1-1 1.1.1 ATRAC compression .......................... 1-1 1.1.2 Buffer memory .................................... 1-1 1.1.3 Random access and U-TOC .
Table of Contents –ii TASCAM MD-801R/P Mk II 4.2.1 Playing back a whole disc .................. 4-1 4.2.2 Playback outputs ................................ 4-1 4.2.3 Monaural playback .............................. 4-1 4.2.4 Playing back a single track .
TASCAM MD-801R/P Mk II 1–1 1 - Introduction This manual cov ers the two models of the MD-801 Mk II product line: the MD-801R Mk II, which is capable of recording and playing back on MiniDisc media, and the MD-801P Mk II, which is for play- back only of such media.
1 - Care of MD media 1–2 TASCAM MD-801R/P Mk II disk from the user , and a file appears as one contigu- ous block of data (e v en though it may be spread o v er many tracks and sectors of the disk), the MD player allo ws separated audio data to appear as a continuous audio track.
1 - About the MD-801R/P Mk II TASCAM MD-801R/P Mk II 1–3 to be con v eniently carried out using a standard k e y- board • Remote control possible from dedicated T ASCAM remote control units (RC-80.
1 - About this manual 1–4 TASCAM MD-801R/P Mk II 1.3.4 Backup memory When the unit is po wered down, the follo wing set- tings are memorized. • A UTO READ Y status (see [20] ) • A UTO CUE settin.
1 - Hookup Examplel TASCAM MD-801R/P Mk II 1–5 1.5 Hookup Examplel.
2–1 TASCAM MD-801R/P Mk II 2 - Front and rear panel features.
TASCAM MD-801R/P Mk II 2–2 2 - Front and rear panel features This section, as well as gi ving a description of the controls and features of the MD-801, also provides many descriptions of basic operations. The section on the rear panel also contains advice on setting up and connecting the MD-801 as part of an audio system.
2 - Front panel 2–3 TASCAM MD-801R/P Mk II T o start recording, press the PLA Y ke y [6] . T o stop recording, press the ST OP ke y [5] . After the ST OP ke y has been pressed, the words T OC EDIT will flash on the display , which will also sho w UTOC Writing as the U-TOC is written to disc.
2 - Front panel TASCAM MD-801R/P Mk II 2–4 • REMAIN —the total time remaining on the disc for further recording (the length of the blank portion of the disc) • TOT A L —the total elapsed tim.
2 - Front panel 2–5 TASCAM MD-801R/P Mk II these edits cannot be committed to disc using the T OC WRITE function (see below). [19] T OC WRITE key and indicator After an edit operation has been selected and per- formed from the EDIT ke y [18] , the T OC WRITE indicator will light, and the T OC EDIT indicator in the display will be lit.
2 - Display TASCAM MD-801R/P Mk II 2–6 mode, the REPEA T indicator will be sho wn on the dis- play . See 4.2.9, "Repeat playback" for further details of this mode.
2 - Rear panel 2–7 TASCAM MD-801R/P Mk II (6) TRA CK TITLE indicator Lights when track titles are being entered or dis- played. See 5.11, "T rack and disc title entry" for details. (7) DISC TITLE indicator Lights when the title of the disc is being entered or displayed.
2 - Rear panel TASCAM MD-801R/P Mk II 2–8 ital outputs [33] and [35] without passing through the frequency con verter . [33] DIGIT AL OUTPUT (AES/EBU) This XLR-type connector outputs digital audio data in AES3-1992 format. The output sampling frequency will al ways be 44.
2 - Rear panel 2–9 TASCAM MD-801R/P Mk II The wiring is, as marked on the rear panel: 1=ground, 2=hot (+), 3=cold (–). The nominal impedance is 11 Ω . The trimmer potentiometers by each connector may be turned counterclockwise or clockwise to cut or boost respecti vely the le vel of the signal sent from these connectors.
TASCAM MD-801R/P Mk II 3–1 3 - Menu items The selections that can be made using the MD-801’ s menu system af fect the operation of many other functions. W e suggest that you tak e the time to look through this section and familiarize yourself with the basic contents, so that you hav e an idea of some of the options av ailable to you.
3 - Resume setting 3–2 TASCAM MD-801R/P Mk II The minimum length for the jog loop is 12 frames, and the maximum v alue is 32 frames. The v alue is set in 1-frame steps.
3 - Incremental play TASCAM MD-801R/P Mk II 3–3 3.10 Incremental play This function allo ws auto-cueing of the playback point to the start of the next track when the ST OP key [5] is pressed, or a fader stop command is recei ved (on pin 8 of the parallel remote control port [47] ).
3 - Auto track numbering level 3–4 TASCAM MD-801R/P Mk II 3.12.1Spindle motor time Use this to check ho w many hours the spindle motor has been in operation. 3.12.2Laser pickup time This indicates ho w many hours the laser pickup has been used for recording.
TASCAM MD-801R/P Mk II 4–1 4 - Basic operations This section gi ves you informstion about the basic operations using the MD-801. It assumes that you hav e connected the MD-801 to all the other equipment that you will be using. If you hav e not already made these connections, read 2.
4 - Playback of discs 4–2 TASCAM MD-801R/P Mk II 4.2.4 Playing bac k a single track When the disc has been loaded and the T OC has been read, use the PLA Y MODE ke y to select the SINGLE play mode (see [22] ). Use the TRA CK ke ys [4] to mov e the playback posi- tion to the start of the desired track.
4 - Playback of discs TASCAM MD-801R/P Mk II 4–3 4.2.9 Repeat playbac k Use the REPEA T key [26] to enable the repeat mode as sho wn in the display ( REPEA T ). The three dif ferent repeat modes av ailable corre- spond to the three playback modes set with the PLA Y MODE key [22] (whole disc, SINGLE track or A-B points, as set abov e).
4 - Recording operations 4–4 TASCAM MD-801R/P Mk II NO TE The point at which the JOG ke y was pressed will not be included in the jog loop . T o include this point in the loop , you m ust tur n the JOG dial counterclockwise .
4 - Recording operations TASCAM MD-801R/P Mk II 4–5 MD-801R model only . 4.3.1 General notes on recording using the MD format Because the MD method of recording is some what dif ferent to a linear recording method, such as tape, you should note the follo wing points.
4 - Recording operations 4–6 TASCAM MD-801R/P Mk II 1 Select the recording method (digital or analog) and the appropriate input source. 2 Make sure the unit is stopped.
4 - Recording operations TASCAM MD-801R/P Mk II 4–7 2 Cue the playback point to the place that you want to start recording. 3 Press the READ Y ke y [7] to put the MD-801 into play ready mode. This step is the primary dif ference between replace recording and ordi- nary post-script recording.
4 - Recording operations 4–8 TASCAM MD-801R/P Mk II vious one. If the digital signal is not resumed within 30 seconds of interruption, recording will stop .
TASCAM MD-801R/P Mk II 5–1 5 - Editing operations Unlike tape or other linear media, the MD-801 pro- vides you with a wide range of editing tools, allo w- ing you to make arbitary cuts, “splices” and rearrangements of running order without having to re-record any parts of the material.
5 - Erasing a track 5–2 TASCAM MD-801R/P Mk II of the loop is the point at which you want to di vide the track. NO TE Y ou can set the length of the jog loop in the menu system (see 3.5, "Jog loop length"). 5 When the start of the jog loop is correctly posi- tioned, turn the SHUTTLE wheel clockwise.
5 - Moving tracks TASCAM MD-801R/P Mk II 5–3 The PLA Y indicator abov e the PLA Y ke y will flash, as will the EDIT indication in the display , to sho w that rehearsal mode has been entered.
5 - A and B point erase operations 5–4 TASCAM MD-801R/P Mk II of operation is the same, the function is so flexible that it can be used for many dif ferent purposes.
5 - Moving an A-B point TASCAM MD-801R/P Mk II 5–5 If the A point is set at the start of a track, and the B point at the end of another track, the whole of the tracks containing and between these points will be erased (in the example abo ve, tracks 2 and 3 will be erased.
5 - Restoring erased material 5–6 TASCAM MD-801R/P Mk II bers are renumbered accordingly . See the dia- gram abov e for an example. If you need to make the ne w track (formerly the A-B portion) into part of the preceding and/or follo wing track, use the track combine facility (see 5.
5 - Erasing a complete disc TASCAM MD-801R/P Mk II 5–7 3 T urn the SHUTTLE wheel clockwise. The dis- play changes: 4 T urn the SHUTTLE wheel clockwise once again to change the current track from mono to stereo or vice versa . The display will sho w Now Editing , follo wed by Complete .
5 - Track and disc title entry 5–8 TASCAM MD-801R/P Mk II tion will mov e the cursor more than one position. 7 Continue using the D ATA dial and SHUTTLE wheel to enter characters, until the title is complete. 8 T o store the title, press the EDIT ke y .
5 - Track and disc title entry TASCAM MD-801R/P Mk II 5–9 5.11.6Copying disc and trac k titles When two MD-801 units are connected together using the optional PW -1XMD serial cable, disc and track titles can be copied from one unit (master) to the other (slav e), as described in 4.
TASCAM MD-801R/P Mk II 7–1 7 - Remote control of the MD-801 The MD-801 can be controlled by a number of dif- ferent sources, including the PS/2 ke yboard described in 6, "Use of a ke yboard with the MD- 801".
7 - REMOTE (PARALLEL) connector 7–2 TASCAM MD-801R/P Mk II For details of the timing of the EOM tally signal (pin 20), see 3.7, "EOM disc" and 3.8, "EOM track". 7.1.2 Fader start Pin 8 is a special case. If this input is brought lo w (for more than 50 ms), playback starts.
TASCAM MD-801R/P Mk II 8–1 8 - Specifications, etc. This section provides reference material concerning the error and informational messages that may appear on the display of the MD-801 under certain circumstances, as well as the specifications of the unit.
8 - Specifications 8–2 TASCAM MD-801R/P Mk II 8.2 Specifications Changes in specifications and features may be made without notice or obligation. In the follo wing specifications, 0 dBV is referenced to 1 volt, and 0 dBu is referenced to 0.775 Vrms.
8 - Specifications TASCAM MD-801R/P Mk II 8–3 8.2.2 Analog I/O 8.2.3 Digital I/O 8.2.4 Other connections 8.2.5 General and electrical Error correction A CIRC (Advanced Cross Interleav e Reed-Solomon Code) F requency response 20 Hz – 20 kHz ±0.
8 - Dimensional drawing 8–4 TASCAM MD-801R/P Mk II 8.3 Dimensional drawing RC-8 Remote Control Unit RC-801 Remote Control Unit Option 216mm 200mm 58mm 156mm 201mm 14mm 4mm 21mm 201mm 22mm.
Index A - E MD-801R/P Mk II I A A and B point erase operations 5-3 A-B erase 5-4 A-B indicator 2-7 A-B point, moving 5-5 About the MD-801R/P Mk II 1-2 About the MiniDisc format 1-1 AES/EBU DIGITAL INP.
Index F - P II MD-801R/P Mk II without saving the edits to disc 5-1 Editing a programmed sequence 6-2 Editing operations 5-1 EJECT key 2-2 Ejecting discs 4-1 End of track, erasing to 5-4 Entering the .
Index R - T MD-801R/P Mk II III Pickup time 3-4 PITCH CONT key and indicator 2-5 Pitch control 3-1 PLAY key and indicator 2-1 PLAY MODE key 2-5 Playback 4-1 between two location points 4-2 displaying .
Index U - W IV MD-801R/P Mk II erasing from the start 5-4 erasing to the end 5-4 moving 5-3 playing back single 4-2 protect 5-7 splitting 5-1 titles 1-2 Track and disc title editing with the keyboard 6-3 Track and disc title entry 5-7 Track auto-numbering level 3-4 Track entry, direct 6-3 TRACK keys 2-2 TRACK NO.
TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: (213) 726-0303 7733 Telegraph Road, Montebello, California 90640 TEAC CANADA LTD. Phone: 905-890-8008 Facsimile: 905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.
デバイスTascam MD-801R/P Mk IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tascam MD-801R/P Mk IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTascam MD-801R/P Mk IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tascam MD-801R/P Mk IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tascam MD-801R/P Mk IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tascam MD-801R/P Mk IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTascam MD-801R/P Mk IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tascam MD-801R/P Mk IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTascam MD-801R/P Mk IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
