BaumaticメーカーISL95SSの使用説明書/サービス説明書
ページ先へ移動 of 24
ISL95SS 90 cm Island cooker hood.
1 User Manual for your Baumatic ISL95SS Cooker h ood 90 cm Island cooker h ood in s tainless s teel NOTE : This User Instruction Manual contains imp ortant information, including safety & installation p oints, which will enable you to get the most out of your appliance.
2 YOUR COOKER HOOD’S SPECIFICATIONS ….……………..………….3 IMPORTANT SAFETY INFO RMATION……………………………….…4-5 CARING FOR THE ENVI RONMENT…………………………………………6 USING YOUR COOKER HOOD……………………………….
3 Congratulations on purchasing a Baumatic Cooker Hood! To fully enjoy using your app liance long into the future, please firstly familiarise yours elf with its specifications, safety advice and operational in structions included in this manual. You will also need this manual to ensure that your Cooker Hood has been installed properly.
Important Safety Information: Please Read this before installing & using. o Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed.
5 o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. o Keep young children from using, playing with or tampering with the cooker hood. Older children and infirm persons should be supervised if they are using the cooker hood.
6 Note : Before discarding an old appliance, switch off and disconnect it from the power supp ly. Cut off and render any plug useless. Cut the cable off directly behind th e appliance to prevent misuse. This should be under taken by a compet ent person.
7 To use your cooker hood: 1) Make sure it has been properly installed. 2) Find the CONTROL PANEL. It is located at the front of the canopy. You have a Pushbutton control panel that looks like one of those pictured below. 3) The CONTROL PANEL’s buttons all perform separate functions.
8 IMPORTANT! : Before cleaning, always ensure that you have switched your cooker hood OFF at the omni-polar switch, set at the wall from t he cable: Cleaning  Clean the external p arts with mild liquid deterg ents on a damp cloth.  Never use abrasive powder, corrosive solvents or brushes.
9 First remove the grille by pu lling down on it. Undo the side catches. You can now clean the anti -grease filter grilles. 9 Soak them for about one hour in hot water with a grease-loosening detergent then rinse off thoroughly with hot water. 9 Repeat the process if needed .
10 a) Changing the light bulb 9 Before changing the light bulb, ensure th at the appliance is not live (i.e., ensure that you have switched it off so that it’s in the ‘0’ position). 9 Remove the metal anti-grease filters (se e Figure 2 below) and find the old bulb located in the light fixture up inside the exposed canopy.
11 _____________________________________________ ____________________________________ _____ Installing / Changing the Carbon Filter . Your Baumatic Cooker Hood uses CARBON FILT ERS to purify the air for the air recirculation function. You will find two filters t hat will attach to both sides of the fan motor (please see fi gures at bottom of page).
12 Before installation and usage, read all t he instructions and ma ke sure that the voltage (V) and th e frequency ( Hz) indicated on the identif ication plate (found inside your Cooker Hood) and all the dat a inside the ap pliance are exactly the same as the voltage and frequency in your home.
13 : The cooker hood must not be fitted above stoves with a radiant top plate. : We recommend that at least two people install this hood. NOTE: Your Baumatic Cooker Hood should only be fitted from a ceiling. Do NOT position it any less than 700 mm (70 cm) above the hob.
14 5) Attach exit connector ‘D’ to the hood using the 2 provided screws. 6) Connect to the room ex haust vent (Fig. 2). 7) Attach 2 of the 4 supporting angles ‘E’ to the motor housing ‘S’ with 2 screws each; make sure that the folds (E1) are facing forwards (Fig.
15 12) Then, insert casing ‘I’ over casing ‘H’ (Fig. 4). 13) Lift the entire unit, keeping it slightly back from plate ‘A’ attached to the ceiling (see Fig.
16 15) Now attach the motor frame using 8 screws (see Fig. 6 and 6.1). 16) Carry out the electrical and (if using as an extractor fan) air exhaust tube connection. 17) Connect the ventilation hose and power lines. 18) Place t he glass O (Fig. 7 & 7.
17 20) Now fix the glass, screwing the 4 knobs ‘Q ’ by hand. 21) Lift the casing ‘H’ up to the ceiling, so that the upper, lateral holes of the casing correspond with those of the plate. 22) Then fix them using the 4 screws provided (Fig. 9). 23) Lift the lower part of the hood ‘K’ (Fig.
18 EXTRACTION OPERATION – Installation Instructions  Ensure that you have fitted the union (‘N’) to the upper part of the hood using the packaged t wo screws supplied inside the packing (Fig. 1 – on r ight). Using a 125 mm diameter pipe, connect the union (N) on the upper part of the hood (see Fig.
19 If something has gone wrong with your Cooker Hood, checking against this chart might keep you from having to call for service. Symptom Solution The cooker hood will not start! • Check that the hood is connected to the electricity supply. • Check that the fan speed control is set properly.
Czech Republic United Kingdom Baumatic CR spol s.r.o. Baumatic Ltd., Amperova 495 Baumatic Buildings, 46215, Librec 6 Bennet Road, Czech Republic Reading, Berkshire RG2 0QX +420 800 185 263 United Kingdom www.baumatic.cz Sales Telephone (0118) 933 6900 Slovak Republic Sales Fax Baumatic Slovakia, s.
2 1.
.
23.
デバイスBaumatic ISL95SSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Baumatic ISL95SSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBaumatic ISL95SSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Baumatic ISL95SSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Baumatic ISL95SSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Baumatic ISL95SSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBaumatic ISL95SSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Baumatic ISL95SSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBaumatic ISL95SSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。