Texas InstrumentsメーカーTLC3578EVM FAMILY TLC3578EVMの使用説明書/サービス説明書
ページ先へ移動 of 32
TLC3578EVM F amily August 2003 Data Acquisition− Digital/Analog Converters User ’ s G uide SLAU1 10.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use.
EVM W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 15 V . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power .
How to Use This Manual v Preface Read This First About This Manual This user ’ s guide describes the characteristics, operation, and use of the following evaluation boards: - TLC3578 EVM Bipolar-Inp.
T rademarks vi FCC Warning This equipment is intended for use in a laboratory test environment only . It generates, uses, and can radiate radio frequency energy and has not been tested for compliance .
Contents vii Contents 1 EVM Overview 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Features 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents viii Figures 2 − 1 Block Diagram 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 − 1 EVM Selection 5-3 . . . . . . . . . . . . . . . . . . . . . . . . .
1-1 EVM Overview EVM Overview Each evaluation board is based on the equivalent ADC. All ADCs use a synchronous serial interface which can be simply interfaced to many micro- controllers using the SPI protocol. Each EVM also incorporates a stable voltage reference, and operational amplifier to ensure a low-noise voltage reference for the ADC.
Features 1-2 1.1 Features - Evaluation board featuring one of the following: J TLC3578 ADC (order TLC3578 EVM) J TLC3574 ADC (order TLC3574 EVM) J TLC3548 ADC (order TLC3548 EVM) J TLC3544 ADC (order .
2-1 Analog Interface Analog Interface T opic Page 2.1 Analog Interface Block Diagram 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Signal Conditioning 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Interface Block Diagram 2-2 2.1 Analog Interface Block Diagram A block diagram for the analog interface of the EVM is shown in Figure 2 − 1. Figure 2−1. Block Diagram TLC3578 TLC3574 TLC3548 TLC3544 TLC2578 TLC2574 Signal Conditioning P1 / J1 The channels are arranged to comply with the EVM standard developed for data converters.
Physical Pinout Description 2-3 Analog Interface 2.4 Physical Pinout Description Samtec part numbers SSW-1 10-22-F-D-VS-K and TSM-1 10-01-T -DV -P provide a convenient 10-pin dual row header/socket combination at P1. This header/socket provides access to the analog input pins of the TL V2553/6.
Configuration Options 2-4 2.6 Configuration Options There are a number of options available via shorting jumpers. These are detailed below: T able 2 − 3.
3-1 Digital Interface Digital Interface The digital interface for the EVM is simply the appropriate digital signals from the ADC routed and presented to the 20-pin digital interface connector . T opic Page 3.1 Physical Pinout Description 3-2 . . . . .
Physical Pinout Description 3-2 3.1 Physical Pinout Description The EVM is designed for easy interfacing to multiple platforms. Samtec part numbers SSW-1 10-22-F-D-VS-K and TSM-1 10-01-T -DV -P provide a convenient 10-pin dual row header/socket combination.
4-1 Power Supply Power Supply The EVM accepts four power supplies. - A dual ± Vs dc supply for the dual-supply op-amps. - A single 5.0 V dc supply for the analog section of the ADC. - A single 3.3 V to 5 V dc supply for the digital section of the ADC.
4-2.
5-1 Getting the Most From Y our EVM Getting the Most From Y our EVM A wide range of prototyping options and software solutions are available from TI , and of fer additional flexibility , reducing your time-to-market. Hardware and software offerings from TI help you easily get from concept to hardware and software prototype.
Additional Hardware Options 5-2 5.1 Additional Hardware Options In general there are three hardware directions that the user can take with the EVM. 5.1.1 Stand-Alone EVM The EVM can be used on its own. Using the EVM in this manner obliges the user to provide a custom digital interface between the EVM and a host system.
Additional Hardware Options 5-3 Getting the Most From Y our EVM Figure 5 − 1. EVM Selection TMS320C671 1 DSK TMS320C3000 Interface Card TMS320C671 1 DSP TLC3578 EVM TLC3574 EVM TLC3544 EVM TLC3548 EVM TLC3578 EVM TLC3574 EVM TMS320C5K / 6K Interface Card 1.
5-4.
6-1 Bill of Materials, Board Layouts, and Schematic Bill of Materials, Board Layouts, and Schematic This chapter contains the EVM bill of materials, board layouts and schematics. T opic Page 6.1 Bill of Materials for EVM 6-2 . . . . . . . . . . . . . .
Bill of Materials for EVM 6-2 6.1 Bill of Materials for EVM Item no. Qty V alue Ref Des Description V endor Part number 1 1 0R R19 Resistor , 0 − Ω 1/16 W 5% 0402 SMD Panasonic ERJ − 2GE0R00X 2 .
Bill of Materials for EVM 6-3 Bill of Materials, Board Layouts, and Schematic 22 1 TLC3578 U4 IC, A/D 8 − CH, 14 − BIT , LP 24 − TSSOP T exas Instruments TLC3578IPW Alternate TLC3574 U4 IC, A/D,.
Board Layouts 6-4 6.2 Board Layouts Figure 6 − 1. T op Layer.
Board Layouts 6-5 Bill of Materials, Board Layouts, and Schematic Figure 6 − 2. Internal Plane 1 Figure 6 − 3. Internal Plane 2.
Board Layouts 6-6 Figure 6 − 4. Bottom Layer (Mirrored).
EVM Schematic 6-7 Bill of Materials, Board Layouts, and Schematic 6.3 EVM Schematic The EVM schematic is a PDF attachment following this page..
1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 12500 TI Boulevard. Dallas, Texas 75243 Title: SHEET: OF: FILE: SIZE: DATE: REV: 21-Aug-2003 Drawn By: Engineer: Revision History REV ECN Number Approved TLC3578 EVM Block Diagram DOCUMENTCONTROL # TLC3578 TLC3578.
1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 12500 TI Boulevard. Dallas, Texas 75243 Title: SHEET: OF: FILE: SIZE: DATE: REV: 21-Aug-2003 Drawn By: Engineer: Revision History REV ECN Number Approved TLC3578.
1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 12500 TI Boulevard. Dallas, Texas 75243 Title: SHEET: OF: FILE: SIZE: DATE: REV: 21-Aug-2003 Drawn By: Engineer: Revision History REV ECN Number Approved PWR & REF.sch DOCUMENTCONTROL # W2 W3 C16 0.1uF + C19 10uF C1 0.
デバイスTexas Instruments TLC3578EVM FAMILY TLC3578EVMの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Texas Instruments TLC3578EVM FAMILY TLC3578EVMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTexas Instruments TLC3578EVM FAMILY TLC3578EVMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Texas Instruments TLC3578EVM FAMILY TLC3578EVMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Texas Instruments TLC3578EVM FAMILY TLC3578EVMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Texas Instruments TLC3578EVM FAMILY TLC3578EVMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTexas Instruments TLC3578EVM FAMILY TLC3578EVMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Texas Instruments TLC3578EVM FAMILY TLC3578EVMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTexas Instruments TLC3578EVM FAMILY TLC3578EVMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
