TN'GメーカーVenice 49ccの使用説明書/サービス説明書
ページ先へ移動 of 33
V enice 49cc Owner ’ s Manual rev05-02.
T able of Contents Safety Notes .......................................................................... Page 2 Description ............................................................................ Page 3 Specifications ..........................
3 DESCRIPTION Seat Headlight Rear V iew Mirr o r 2 Cycle Mixing Oil Cover Muffler Throttle Rear Brake Lever Kick S tarter VIN Number Fr ont Brake Lever Speedometer Instrument Cluster Ignition Switch F.
4 Opening the Seat Insert the ignition key into the seat lock & turn to the right. Raise the rear of the seat to the upright position. Remove the ignition key . Closing the Seat Press the seat down to its normal position. Check the seat to make sure that it is locked in position.
5 T ransmission CVT Fuel Capacity 5.5 Liters / 1.5 Gals Rear Drive Oil T ype SAE20W -40 Rear Drive Oil Capacity Gear Box (100 cc) Fuel Mixing Oil Amsoil (Synthetic 2-stroke) Fuel Mixing Oil Capacity 4.
6 OPERA TING CONTROLS Ignition Switch (OFF) Power not applied to the lighting & ignition circuit. (ON) Power applied to the lighting & ignition circuit. Key cannot be removed from switch in this position. (LOCK) Steering mechanism locked into place.
7 Stop Switch Run Position Starter Button Stop Position S top Switch The Stop switch has two positions: Stop- Engine stops running. Run- Engine can run. S t art Button T urn the key in the ignition switch to on, hold the rear brake lever lightly , press the starter button & the starter motor will crank the engine.
8 Adding Fuel Note: T urn the engine off when refuelling Remove all source of flame from the area when refuelling. Unlock fuel cap, remove cap and add fuel. Capacity is approximately 1.5 gallons. No need to pre-mix oil with fuel. Oil will be added automatically during operation.
9 Adjusting the Brakes Rear Brake Adjustment Park the scooter on its center stand on a flat surface. Check the rear brake free play by measuring how far the tip of the brake lever will move until it begins to resist further movement. (See Figs 1 1 & 12) Brake lever at rest.
10 When turning the brake adjustment nut, make sure that the nut rests in the correct position when you remove the wrench. The concave surface of the nut must rest flush against the pivot pin. (See Fig 14) Make sure that the brake adjustment nut does not look like Fig 15! This brake has been adjusted incorrectly .
11 T ires T ire pressure should be checked frequently . The cold tire pressures are as follows: Front 25 PSI Rear 30 PSI T ires should be regularly checked for damage to the rim as well as damage to the tire itself. Look for any cuts, embedded nails, or other sharp objects.
12 OPERA TING THE SCOOTER S t arting the Engine (cold) T urn the ignition switch to the “ON” position. Hold the rear brake lever to apply rear brake. Set the stop switch to the “run” position (page 8). Do not open the throttle with your right hand.
13 Controlling the Speed The scooter ’ s speed is adjusted by the throttle control. Rotate the control counterclockwise slowly to increase the speed, and rotate the control clockwise to decrease the scooter ’ s speed. Using the Brakes The brakes work best when the front and rear brakes are applied at the same time.
14 S teering Mechanism Examine the front fork to be sure it is not bent or damaged. Raise & lower the front of the scooter and rock it from side to side while listening for any unusual sounds caused by bent front forks. Also turn the front steering axle to make sure that it is not binding or too loose.
15 Fig. 17 Once the 5 screws have been removed, the cover can be carefully opened to reveal the filter element located within. (See Fig 17) Fig. 18 Gently remove the filter element for inspection & possible cleaning. (See Fig 18) The air filter can be cleaned using compressed air and returned to service.
16 Battery The battery is a “maintenance free” type. It should not require electrolyte replacement. T o maintain a full char ge on the battery , it is best to use the kick starter for short trips. Always char ge the battery before storing the scooter for long periods of time.
17 3) After the fluid has stopped draining, replace the drain plug in the drain hole and tighten the plug with a wrench until it is snug. (Do not over- tighten the plug!) 4) Unscrew the rear drive oil filler cap located on top of the rear drive assembly beside the rear wheel.
18 Spark Plug Locate the spark plug by parking the scooter on it’ s side stand and looking underneath the chassis from the right side of the scooter . (See Fig 23) Pull off the spark plug cap, and remove the spark plug with the spark plug wrench provided in the tool kit.
19 Carburetor Adjustment Start the engine and let it idle for 5 minutes. Adjust the idle adjustment screw until the engine idles at 1500 +/- 100 RPM. (See Fig 25) Fig. 25 Idle Adjustment Screw Better access to the carburetor is obtained by raising the seat and remov- ing the screws which hold the luggage box in place.
20 3) Is the stop switch in the run position? Review the Start Switch section on page 8. 4) Is there a spark at the spark plug? Review the Spark Plug section on page 21 . 5) Is gas flowing to the carburetor? Raise the seat and remove the screws which hold the luggage box in place.
21 5) Are the fuses OK? After making sure the ignition is turned off, expose the battery wiring. (Review the opening the battery compartment procedure on page 8) Locate the fuse block (See Fig 27) Slide the spare fuse holder over the end of the fuse block and open the fuse block.
25 22 IGNITION MODULE REPLACEMENT If the ignition module must be changed, then use the following procedure. 1) Park the scooter on it’ s side stand and look underneath the scooter floorboard just behind the front wheel. Locate and remove the front screw which holds the cover unit in place.
23.
24 ROUTINE MAINTENANCE SCHEDULE SCOOTER STORAGE If your scooter will not be used for two months or more, you should store it properly to ensure that it will run reliably when you take it out of storage. It is also advisable to make any repairs to the scooter that it may need prior to storage.
W arranty CMSI, Inc., warrants to the first retail purchaser of all TN’G scooters from an Authorized CMSI Dealer and each subsequent owner that the vehicle is free from defects in materials and workmanship for the period stated in this warranty section.
T o perform warranty repairs on any T N’G product that qualifies for such repairs. The selling dealer shall sign the Acceptance Certificate and a Card of Delivery upon delivery of the vehicle.
W arranty T ime Period for 49cc scooter models Coverage Begins The date the motorcycle is delivered to the first retail purchaser . W arranty CMSI shall repair or replace, at its option, any part (including parts of the emission control system) that is found defective in material or workmanship under normal use for the applicable time period.
Y our Legal Rights These warranties give you specific legal rights. Y ou may also have other rights which vary from state to state. It is the responsibility of the owner to be aware of state laws which pertain to this issue in your particular state.
DISTRIBUT ORS LIMITED W ARRANTY – NEW MOTORCYCLE T N’G warrants to the first retail purchaser and subsequent purchasers of this vehicle that the motorcycle is free from defects in materials ands work- manship for the period stated in “W arranty T ime Period”.
DISTRIBUT OR’S LIMITED W ARRANTY - MOT OR- CYCLE TIRES W arranty T ime Period 90 days, or until the center tread is worn to a depth of 3/32" , whichever occurs first.
This W arranty Does Not Cover • T ires installed on non-CMSI Inc vehicles • T ires worn beyond the service limit specified in the appropriate Owners” Manual. • T ires rendered unserviceable by road hazard damage, such as impact breaks, punctures, cuts, or snags.
Parts installed by an Authorized CMSI/TN’G Dealer: Parts & Labor : No charge. Parts not installed by an Authorized CMSI/T N’G Dealer: Parts : No charge Labor : Y ou pay for removal/installatio.
CMSI Inc. 8146 304th Ave SE Preston, W A 98050 www .cmsiinc.com Rev05-2.
デバイスTN'G Venice 49ccの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TN'G Venice 49ccをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTN'G Venice 49ccの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TN'G Venice 49ccの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TN'G Venice 49ccで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TN'G Venice 49ccを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTN'G Venice 49ccの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TN'G Venice 49ccに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTN'G Venice 49ccデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
