TOA ElectronicsメーカーHX-5Bの使用説明書/サービス説明書
ページ先へ移動 of 16
OPERA TING INSTRUCTIONS SPEAKER SYSTEMS HX-5B HX-5W HX-5B-WP HX-5W -WP Thank you for purchasing TOA's Speaker System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment. T ABLE OF CONTENTS 1.
2 When Installing the Unit • Refer all installation work to the dealer from whom the speaker was purchased. Installation for flying requires extensive technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting in possible personal injury.
3 When Installing the Unit • Avoid touching the unit's sharp metal edge to prevent injury. • To avoid electric shocks, be sure to switch off the unit's power when connecting speakers.
4. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITR Y The speaker system features internal input overload protection circuitry. If an extremely high input level is fed to the unit, the protection circuitry automatically cuts off the signal to the tweeters.
5 6. DIMENSIONAL DIAGRAM [Top] [Front] • HX-5B/5W Input Section • HX-5B-W P/5W-WP Input Section [Side] [Rear] 408 (16 1/16 ) 342 (13 15/32 ) 546 (21 1/2 ) Unit: mm (inches) Rear plate Input section Screw terminals Speaker cable (60 cm or 23 5/8 in.
8. INPUT SECTION 8.1. HX-5B and HX-5W • The 2 Speakon connectors are internally connected in parallel to the screw terminals; you can use either one. • The right table shows the pin arrangement of the Speakon NL4MP connector. • The usable connector (on the cable end) for the Speakon NL4MP is Speakon NL4FC.
7 9. CHANGING THE SPEAKER'S DIRECTIVITY ANGLE The speaker system's directivity angle mode is factory-preset to 60 ° , but this mode can be changed to 45 ° , 30 ° , or 15 ° by following the procedure described below. The figure on the right shows the speaker system in 60 ° mode.
8 Step 3. Reposition the 4 bolts to the desired directivity angle, then retighten them securely. The sound coverage area can also be made asymmetrical by shifting the position of each bolt to different directivity angle. Step 4. Reposition the speaker system by turning it upside down.
9 10. SUSPENDED INST ALLA TION The speaker systems may be suspended either vertically or horizontally. Step 1. For vertical suspension: Remove the speaker grill on the module to be suspended. (Below, upper) For horizontal suspension: Remove the speaker grills on the modules at both ends of the speaker system.
10 Step 2. For vertical suspension: Remove the 2 front bar fixing bolts. (Below, upper) For horizontal suspension: Remove the 4 front bar fixing bolts.
11 Step 3. Fix the suspension bracket and the front bar with the bolts removed in step 2. Step 4. For vertical suspension: Turn the speaker system upside down. Then, mount the suspension bracket in the same manner as described in steps 2 and 3. Observe the following instructions to tighten the bolts securely.
12 Be sure to select wires, chains, and/or anchor shackles with a safety factor appropriate to the weight of the speaker system. Incorrect selection of these suspension components may cause the speaker system to fall, potentially resulting in damage and/or personal injury.
[Direct wall mounting dimensions] (Angle mode of 60 ° ) 408 (16 1/16 ) 131 (5 5/32 ) 4-12 x 41 (4- 15/32 x 1 39/64 ) 546 (21 1/2 ) 181 (7 1/8 ) 6 ( 15/64 ) 23 ( 29/32 ) Unit: mm (inches) Rear plate S.
14 12. MOUNTING BRACKET TYPES The following mounting brackets are optional. Consult the instruction manual enclosed with each bracket for details on their installation and use. • Speaker Rigging Frames HY-PF1B, HYPF1W, and HY-PF1WP Can be used to suspend the speaker system from high ceilings.
15 13. COMBINA TION WITH THE MT -200 MA TCHING TRANSFORMER Using the optional MT-200 matching transformer allows the speaker system to be connected to a high- impedance amplifier.
Printed in Indonesia 533-06-125-50 15. SPECIFICA TIONS Note: The design and specifications are subject to change without notice for improvement. • Accessories Suspension bracket .................................... 2 Hex head wrench ................
デバイスTOA Electronics HX-5Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
TOA Electronics HX-5Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTOA Electronics HX-5Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TOA Electronics HX-5Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TOA Electronics HX-5Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TOA Electronics HX-5Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTOA Electronics HX-5Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TOA Electronics HX-5Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTOA Electronics HX-5Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。