ToshibaメーカーB-450-Rの使用説明書/サービス説明書
ページ先へ移動 of 20
PRINTED IN JAPAN TOSHIBA Barcode Printer B-450-R SERIES Document No. E O 18-33021 Original Jun., 2008 (Revised ) Maintenance Manual.
EO18-33021 CAUTION! 1. This manual may not be copied in whole or in part without prior written perm ission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. Copyright © 2008 by TOSHIBA TEC CORPORATION A ll Rights Reserved 570 Ohito, Izunokuni-shi, Shi zuoka-ken, JAPAN TABLE OF CONTENTS Page 1.
1. UNPACKING EO18-33021 1.1 PROCEDURE 1- 1 1. UNPACKING 1.1 PROCEDURE 1) Open the carton. 2) Unpack the side pad (R) and cushions and the printer from the carton. 3) Place the printer on a level surface. 1.2 CHECKS Check for damage or scratches on the printer.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.1. REPLACING THE CPU PC BOARD 2- 1 2. MAJOR UNIT REPLACEMENT WARNING! Disconnect power cord before replacing important parts. Lubrication CAUTION: 1) Lubrication: During parts replacement. 2) Kinds of oil: 1Kg can.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.1. REPLACING THE CPU PC BOARD 2- 2 4) Remove the PT-3x10 screw and detach the Side Cover R from the printer. 5) Disconnect the seven harnesses from CN1, CN2, CN5, CN8 to CN10, and CN500 on the CPU PC Board. 6) Remove the T-3x10 screw and the Ground Wire to detach the CPU PC Board.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.1. REPLACING THE CPU PC BOARD 2- 3 7) Release the two Hooks securing the Printer Unit. 8) Detach the Printer Unit from the Bottom Cover.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.1. REPLACING THE CPU PC BOARD 2- 4 9) Remove the four screws (T-3x10 and SMW-3x6) a nd detach the CPU PC Board Ass’y from the Printer Block. 10) Remove the four screws (S MW-3x6 and P-3x6) and detach the CP U PC Board from the PC Board Attached Plate.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.2. REPLACING THE MOTOR 2- 5 2.2 REPLACING THE MOTOR 2.2.1 Ribbon Motor 1) Remove the CPU PC Board Ass’y. (Refer to Section 2-1) 2) Remove the two PT-3x10 screws and harnesses to detach the Ribbon Motor Attaching Plate.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.2. REPLACING THE MOTOR 2- 6 2.2.2 Stepping Motor WARNING! Be careful not to get burned when handling the stepping motor since it becomes very hot while printing. 1) Remove the CPU PC Board A ss’y. (Refer to Section 2.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.3. REPLACING THE PS UNIT 2- 7 2.3 REPLACING THE PS UNIT WARNING! Replace only with the same type and rated of fuse for continued protection against risk of fire. 1) Remove the Top Cover and Side Co ver L. (Refer to Section 2.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.3. REPLACING THE PS UNIT 2- 8 4) Release the two Hooks securing the Printer Unit. 5) Detach the Printer Unit from the Bottom Cover.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.3. REPLACING THE PS UNIT 2- 9 6) Detach the PS Unit from the Bottom Cover. 7) Replace the PS Unit as an assembly, then, reasse mble in the reverse order of steps 1) to 6). To replace the Fan Motor, Power Harness, Inlet Ass’ y, PSU Cover, etc.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.3. REPLACING THE PS UNIT 2- 10 10) Push both sides of the Power Switch with something like pliers and remove it from the frame of the PS Unit. Disconnect the Inlet Ass’y from CN1 on the PS Unit. 11) Remove the SMW-3x4 screw to detach the F an Motor Attachment Plate from the PS Unit.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.4. REPLACING THE PRINT HEAD 2- 11 2.4 REPLACING THE PRINT HEAD CAUTION: 1. NEVER touch the element when handling the print head. 2. NEVER touch the connecto r pins Touching them may cause a static electric discharge which will damage the print head.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.5. REPLACING THE MEDIA SENSOR 2- 12 2.5 REPLACING THE MEDIA SENSOR 2.5.1 Replacing the Sensor PCB (TR) 1) Push down the Head Release Lever R to open t he Print Head Block. (Refer to Section 2.4) 2) Remove the Sensor Holder fr om the Sensor Holder Arm.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.5. REPLACING THE MEDIA SENSOR 2- 13 5) Disconnect the harness from the Sensor PCB (TR), and remove the Sensor PCB (TR) from the Sensor Holder by releasing the two Rivets. 6) Replace the Sensor PCB (TR) with a new one, and then reassemble in the reverse order of removal.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.5. REPLACING THE MEDIA SENSOR 2- 14 2.5.2 Replacing the Sensor PCB (LED) 1) Open the Top Cover. 2) Remove the two PT-3x10 screws to detach the Side Cover L. 3) Disconnect KEY/LED Harness from c onnector CN13 on the CPU PC Board.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.5. REPLACING THE MEDIA SENSOR 2- 15 Printer Unit 5) Disconnect the Power Harness and Fan Motor Harness from CN8 and CN10 on the CPU PC Board.
2. MAJOUR UNIT REPLACEMENT EO18-33021 2.5. REPLACING THE MEDIA SENSOR 2- 16 7) Detach the Printer Unit from the Bottom Cover. 8) Disconnect the har ness from the Sensor PCB (LED) whic h is attached to the bottom of the Printer Unit. Then remove the Rivet to detach the Sens or PCB (LED) from the Printer Unit.
3. TROUBLESHOOTI NG EO18-33021 3. TROUBLESHOOTING 3- 1 3. TROUBLESHOOTING Problems Cause Solution Power is not turned ON. 1. Input voltage to the printer is not within the rated voltage. 2. Output voltage from the printer is not within the rated voltage.
デバイスToshiba B-450-Rの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toshiba B-450-Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba B-450-Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba B-450-Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba B-450-Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba B-450-Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba B-450-Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba B-450-Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba B-450-Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。