ToshibaメーカーB-EP4DLの使用説明書/サービス説明書
ページ先へ移動 of 27
PRINTED IN JAPAN TOSHIBA Potable Printer B-EP4DL SERIES Document No. EO18-33023 Original Sep., 2008 (Revised ) Maintenance Manual.
WARNING! Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. NOTE: Failure to follow manual instructions or any unauthorized modification, substitution orchange to this product will void the limited product warranty.
EO18-33023 (Revision Date: Dec. 16, 2008) CAUTION! 1. This manual may not be copied in whole or in part without prior written perm ission of TOSHIBA TEC.
1. UNPACKI NG EO18-33023 1.1 Procedure 1- 1 1. UNPACKING 1.1 Procedure 1) Open the carton. 2) Unpack the accessories from the carton. 3) Unpack the printer. NOTE: Keep the carton and pad for future transportation of the printer. 1.2 Checks 1) Check for damage or scratches on the machine.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2-1 2. MAJOR UNIT REPLACEMENT WARNING! 1. Disconnect the power cord before installing the main parts. 2. Be careful not to injure your fingers when replacing the main parts. CAUTION! 1.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2-2 4) Press the Top Cover Open Button to open the Top Cover. 5) Remove the Left Side Cover in the direction of the arrow. 6) Remove the Right Side Cover and the Front Cover in the direction of the arrow, respectively.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2-3 7) Remove the Front Cover. 6) Disconnect all Connectors and FPC Cable from the CPU PC Board. NOTE: Before disconnecting the FPC Cable, release the Connector Lock. 7) Disconnect the Earth Terminal from the Drive PC Board.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2-4 8) Open the Hooks, then remove the CP U PC Board from the Front Cover. 9) Remove the screw, then remove the Earth Terminal. 10) Replace the CPU PC Board with a new one, then reassemble in the reverse order of removal.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2-5 11) Close the front cover. 12) Mount the left side cover to the printer while fitting the tabs on the left side cover into the slots of the printer enclosure. Fit the tabs A to D into the slots A’ to D’.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.1 Replacing the CPU PC Board 2-6 13) Mount the rig ht side cover to the printer while fitting the tabs on the right side co ver into the slots of the printer enclosure. Fit the tabs A to C into the slots A’ to C’.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.1 Replacing the CPU PC Board 2-7 NOTES: 1. After replacing the CPU PC Board, refer to t he Setting Operation Manual or System Mode Manual an d perform the following operations. 1. Perform a RAM clear.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.2 Replacing the LCD Unit 2-8 2.2 Replacing the LCD Unit 1) Remove the Right Cover, Left Cover, Fr ont Cover and CPU PC Board. (Refer to Section 2. 1 Replacing the CPU PC Board .) 2) Remove the three screws, then remove the LCD Unit.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.3 Replacing the Peel-off Roller 2-9 2.3 Replacing the Peel-off Roller 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Remove the two Roller Clips with a straight slot screwdriver, then remove the Peel-off Roller Ass’y.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.4 Replacing the Peel-off Sensor 2-10 2.4 Replacing the Peel-off Sensor 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Disconnect the Connector from the CPU PC Board.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.4 Replacing the Peel-off Sensor 2-11 6) Replace the Peel-off Sensor with a new one, t hen reassemble in the reverse order of removal. NOTES: 1.Be careful of the orientation of the Peel-off Sp rings as shown in the picture below when reassemblin g the Peel-off Sensor Unit.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.5 Replacing the Drive PC Board 2-12 2.5 Replacing the Drive PC Board 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Disconnect all Connectors and FPC C able from the Drive PC Board.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.6 Replacing the Battery Terminal 2-13 2.6 Replacing the Battery Terminal 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Remove the Drive PC Board. (Refer to Section 2.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.7 Replacing the Stepping Motor 2-14 2.7 Replacing the Stepping Motor 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Remove the two screws. 3) Disconnect the Connector from the Drive PC Board.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 2-15 2.8 Replacing the Print Head 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Release the Hooks, then remove the Media Sensor Holder Ass’y upward.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 2-16 5) Disconnect the Head FPC from the Print Head Connector. NOTE: When reassembling the Head FPC, the contact portion should be faced upward.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 2-17 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 2-18 5) Remove the Cover Open Switch (L) and Cover Open Switch (R) from the Base Cover.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.10 Replacing the Media Sensor (Upper) 2-19 2.10 Replacing the Media Sensor (Upper) 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board .) 2) Remove the two screws which secure the Outlet Paper Guide Ass’y.
2. MAJOR UNIT REPLACEMENT EO18-33023 2.10 Replacing the Media Sensor (Upper) 2-20 5) Replace the Media Sensor (Upper) with a new one, then reassemble in the reverse order of removal. NOTE: A fter replacing the Media Sensor, refer to the Setting Operation Manual o r System Mode Manual an d p erform the following operations.
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.10 Replacing the Platen Ass’y 2-21 2.11 Replacing the Platen Ass’y 1) Remove the Upper Sensor Cover. (Refer to Section 2.9 Replacing the Media Sensor (Upper) .) 2) Release the Hooks, then remove the Platen Ass’y.
3. TROUBLESHOOTI NG EO18-33023 3. TROUBLESHOOTING 3- 1 3. TROUBLESHOOTING Problems Cause Solution The printer is not turned on. 1. The battery is not loaded correctly. 2. The battery terminal is disconnected from the soldering part. 3. CPU PC board ass'y failure or Drive PC board ass'y failure 1.
3. TROUBLESHOOTI NG EO18-33023 3. TROUBLESHOOTING 3- 2 Problems Cause Solution The printer does not print labels one by one in the strip mode or specified number of labels in the batch mode. 1. The sensors are not adjusted properly. 2. The sensors are not installed properly.
デバイスToshiba B-EP4DLの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba B-EP4DLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba B-EP4DLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba B-EP4DLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba B-EP4DLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba B-EP4DLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba B-EP4DLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba B-EP4DLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba B-EP4DLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
