ToshibaメーカーIK-1000の使用説明書/サービス説明書
ページ先へ移動 of 40
INSTRUCTION MANU AL CCD COLOR CAMERA IK-1000 T ABLE OF CONTENTS IMPOR T ANT SAFEGU ARDS ................................................. 3 1. CA UTIONS ON USE AND INST ALLA TION ................... 5 2. COMPONENTS ....................................
.
- 3 - 1. Read Instructions All the safety and oper ating instructions should be read bef ore the product is operated. 2. Retain Instructions The safety instructions and instruction manual should be retained f or future reference . 3. Heed W arnings All warnings on the product and in the instruction manual should be adhered to .
- 4 - CA UTION T O REDUCE THE RISK OF ELECTRIC SHOCK. DO NO T REMOVE CO VER (OR BA CK). NO USER SER VICEABLE P ARTS INSIDE. REFER SER VICING TO Q UALIFIED SER VICE PERSONNEL.
- 5 - 1. CAUTIONS ON USE AND INST ALLA TION • On installation, observe the following matters: - Do not bloc k the radiation fan's holes. - Do not place cloth including a tablecloth o v er the fan. - Do not place the camera on the carpet or cushion.
- 6 - • When cleaning the camera Unplug the power source bef ore cleaning. Clean with a soft dry cloth. If the dust is hard to take off, softly wipe off with a cloth soak ed in mild detergent. Do not use volatile chemicals such as thinner , benzene, and insecticide.
- 7 - !1 Camera Support Fitting !2 IRIS terminal (4P) !3 Imaging unit !6 C mount ring lock scre w !7 C mount ring !4 Tripod setting hole !5 Iris selection switch * For detailed dimensions , refer to the e xter nal view on page 33.
- 8 - q DC IN 12V terminal Accepts a DC power unit (12 V). w VIDEO ter minal Outputs VBS signal. Connected to monitor , recording device , etc. (BNC connector) e RS232C terminal Used to control functions by communications via RS232C . r DISP button Used when switching the displa y .
- 9 - !5 Iris selection switch Select the types of automatic iris lenses (DC lens and Video lens). !6 C mount ring, lock scre w Locks bac k f ocus adjusting r ing. !7 C mount ring Install the C mount lens. • When attaching the camera to a tripod, fasten the tripod to the camera tripod setting hole without sliding them from each other .
- 10 - 4. CONNECTION Lens Camera body Monitor DC 12 V power supply DC IN 12V terminal VIDEO terminal Coaxial cable of 75Ω • When installing the camera, unplug the power source of the camer a and all connected equipment. • Please use a monitor which has BNC or S-Video input.
- 11 - 5. LENS ADJUSTMENT 5.1 A vailable Lens Use a C mount lens whose rear flange projection is 9 mm or less. C mount 9 mm or less • When using a zoom lens or a lens of 400 g or more , be sure that the lens is supported to prev ent damage to the C mount r ing.
- 12 - • Do not adjust the lens side in the adjustment in (5). Interference of e xposure control between lens and camera body ma y cause noisy video image and hunting.
- 13 - 6. OPERA TION q Referring to the above item “4. CONNECTION,” connect necessary equipment. w Tu rn on the connected equipment and the po wer source of this camera. e P oint the lens at the object, operate the lens iris adjustment, focus adjustment, etc.
- 14 - 6.1.1 AUTO Mode In the A UTO mode, the brightness and sensitivity of video image can automatically be controlled for each of f our sensitivity controls according to the brightness of object.
- 15 - 6.2.1 ONE PUSH WB (One Push White Balance) • Set the MODE to ONE PUSH WB on the WHT BAL setting screen. (Refer to the item “7.4.1 “WHT BAL (White Balance)””) • If the screen displays a color bar and the index/setting screen is displayed, press the [DISP] button to clear the color bar and char acter display on the setting screen.
- 16 - Display Meaning A WB OK Automatic white balance adjustment finished correctly . A WB NG Automatic white balance adjustment cannot be perf ormed because the video level LEVEL LO W is too low .
- 17 - 7. MODE SETTING BY ON SCREEN DISPLA Y Va r ious settings can be controlled on the unit by using the on screen menu displa yed on the monitor . The contents once set are memorized in the SCENE files (A, B and C) ev en if the power source is turned off.
- 18 - 7.2 Items that can be set on screen display P age Mode Preset name name Set item name (factory setting) Par ameter Content status 1 SENS A UTO FLICKER ON/OFF Flicker-less mode OFF (1/100s electronic shutter) ON/OFF CMG MAX OFF , CMG1, CMG2, ...
- 19 - 7.3 SENS (sensitivity setting) The sensitivity of this unit can be se to A UTO and MANU AL. Place the cursor “ → ” on MODE, press the [DA T A UP] or [D A T A DO WN] button, and select the desired mode from A UTO and MANU AL. AU TO :A utomatically control the e xposure time to get the set lev el.
- 20 - (1) Changing flick er correction FLICKER is capable of correcting fluorescent flic ker generated in 50 Hz area. Setting FLICKER to ON fixes the electronic shutter to 1/100s , removing fluorescent flick er. Howe ver , if A UT O SENS enters long ter m exposure control, the electronic shutter is s witched from 1/100s to long term.
- 21 - (4) Changing the setting of maximum v alue of AUT O long term exposure q Using the [MENU UP] or [MENU DO WN] b utton, place “ → ” on SS LONG MAX. w Using the [D A T A UP] or [D A T A DOWN] b utton, set the maximum value of A UT O long term exposure.
- 22 - (7) Changing brightness detection area q Using the [MENU UP] or [MENU DO WN] b utton, place “ → ” on AREA. w Using the [D A T A UP] or [D A T A DOWN] button, select PEAK or A VERAGE.
- 23 - 7.3.2 When Changing Settings of MANUAL mode and MANUAL Shutter mode Up/down mov ement by M ENU UP/DOWN Set by D A T A UP/DOWN -- 1 SENS -- <FILE A> <SENS MODE=MANUAL, SHUTTER MODE=MANU.
- 24 - 7.3.3 When Changing Settings of MANUAL mode (Synchro. Scan mode) Up/down mov ement by MENU UP/DOWN Set by D A T A UP/DOWN -- 1 SENS -- <FILE A> <SENS MODE=MANUAL, SHUTTER MODE=SS> M.
- 25 - 7.4 WHT BAL (White Balance) WHT BAL has three modes: ONE PUSH WB , A TW and MANU AL. Place the cursor “->” on MODE, press the [DA T A UP] or [DA T A DOWN] button, and select the desired mode from ONE PUSH WB, A TW , MANUAL.
- 26 - (3) Changing ONE PUSH WB area q Using the [MENU UP] or [MENU DO WN] b utton, place “ → ” on AREA w Using the [D A T A UP] or [D A T A DOWN] b utton, set the photometer area.
- 27 - 7.4.2 When Changing Settings of A TW (Automatic Tracking White Balance) Mode Up/down mov ement by MENU UP/DOWN Set by D A T A UP/DOWN -- 2 WHT BAL ATW -- <FILE A> MODE ATW R PAINT 0 B PAI.
- 28 - 7.4.3 When Changing Settings of MANUAL (Manual White Balance) Mode Up/down mov ement by MENU UP/DOWN Set by D A T A UP/DOWN -- 2 WHT BAL -- <FILE A> MODE MANUAL R GAIN 0 B GAIN 0 ・ Disp.
- 29 - 7.5 PROCESS (Process) Up/down movement by MENU UP/DOWN Set by DA T A UP/DOWN -- 3 PROCESS -- <FILE A> GAMMA ON DTL ON ・ Display of SCENE file ・ Gamma correction ON, OFF ・ Detail ON, OFF (1) Changing ON/OFF of gamma correction q Using the [MENU UP] or [MENU DOWN] button, place “ → ” on GAMMA.
- 30 - 7.6 OPTION (Option) Up/down mov ement by MENU UP/DOWN Set by D A T A UP/DOWN -- 4 OPTION -- <FILE A> BAUD RATE 19200bps SCENE FILE A TEMP.
- 31 - (4) Changing the setting of electronic multiplication offset q Using the [MENU UP] or [MENU DO WN] b utton, place “ → ” on CMG OFFSET . w Use the [D A T A UP] or [D A T A DOWN] b utton to make setting.
- 32 - 8. TROUBLESHOOTING! Symptom Where to check Video image does • Is the iris selection switch set correctly according to the lens? not appear . • Is the lens iris adjustment correct? • Are c.
- 33 - 79.25 (3.12) 133 (5.24) 27.8 (1.09) 25.34 (1.00) 48.34 (1.90) 4-R3.5 (0.14) 35 (1.38) 58 (2.28) 45.75 (1.80) 94.35 (3.71) 12.8 (0.50) 22 (0.87) 19 (0.75) 28 40 (1.57) 7 (0.28) 58.4 (2.30) ø R72 5 (0.20) C-MOUNT RING LOCK SCREW C-MOUNT RING RA TING LABEL 1/4-20 UNC CD LEVEL 9.
- 34 - 10. SPECIFICA TIONS Pow er supply Pow er consumption Imaging element Effectiv e number of pixels Scanning system Scanning frequency Synchronous system Resolution Minimum subject intensity S/N V.
- 35 -.
- 36 -.
- 37 -.
- 38 -.
- 39 -.
one (1) year one (1) year one (1) year deliver If technical support deter mines unit is defective , RMA will be issued with return instructions for repair. Y ou must notify (877) 855-1349 within (30) days after you disco ver that the product does not perform in accordance with specifications during the Limited W arranty period.
デバイスToshiba IK-1000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba IK-1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba IK-1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba IK-1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba IK-1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba IK-1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba IK-1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba IK-1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba IK-1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
