ToshibaメーカーNTDVT006BKの使用説明書/サービス説明書
ページ先へ移動 of 11
TOSHIBA Ser vice T raining "Customer Satisfaction Through Knowledge" T OSHIB A DVD SER VICE GUIDE "In Touch With Tomorrow" T OSHIB A AMERICA CONSUMER PR ODUCTS, INC.
T OSHIB A DVD SER VICE GUIDE Copyright © 1997 T OSHIBA AMERICA CONSUMER PRODUCTS, INC.NA TIONAL SER VICE DIVISION NA TIONAL TRAINING DEP ARTMENT 1420-B T OSHIBA DRIVE LEBANON, TN 37087.
CONTENTS INTRODUCTION 1. This book supplements video tape NTDVT006, T oshiba DVD Servicing. It covers the mechanical disassembly and reassembly of a DVD player , and how to diagnose a problem to the board level. For more detailed information and drawings refer to service manual 810-9601.
the 2 self tapping screws on the back panel. 7. Remove the top portion of the shield and set it aside. 8. Unclip the wires leading to the power supply . 9. Lift the main board and remove the bottom portion of the shield. Then rest the main board in the built-in holders.
7. Retract the 2 screws on either side of the motor pulley . 8. T urn the mechanical assembly over and release the 3 tabs holding the loading motor PC board.
portion of the lever . 1 1. Push the slider back and forth to confirm the operation of the opening and closing gears. 12. Replace the 2 screws holding the loading motor in place. 13. Replace the loading belt. 14. Slide the lift assembly into place, and replace the 2 holding screws.
left and right analog audio. In the right position you get left and right analog audio and no AC-3 audio. If you change the position of the audio selector switch, you must cycle the power so the change is recognized by the microprocessor .
tween the 2 boards occur during low transi- tions. 4. Using pin 7 as the reference, monitor the clock signal on pin 6 of CN602. There are eleven negative clock pulses during 1 low cycle of the FSTBX signal. 5. Check the DSPSO signal on pin 5 of CN602.
to check the operation of the signal. If the signal is missing or improper , the main board is most likely at fault. 4. Play a CD and check the tracking error signal at TP507 5. Check for a focus or tracking problem at pins 1, 2, 3, and 4 of CN501. These are the focus and tracking drive signals going to the laser slide assembly .
attempt at the drive signal coming on. 20. Check the feedback from the spindle motor hall switches by monitoring pins 9 through 13 and pin 15 while cycling power and playing a disc in times 8 scan. 21. Check the spindle motor hall switches manu- ally by rotating the spindle motor with your finger while monitoring pins 9 through 13 and pin 15.
CN80 1 CN50 1 CN30 2 CN50 2 CN50 3 CN602 In dicates Pin One MAIN BOARD CO MPO N EN T SID E (CN3 02 - SD30 0 6 Only) CN801 1 NC 2 EVER 5V 3 POW ER ON 4 +5V 5 +9V 6 +8V 7 +5V 8 +3V 9 GND 10 GND 11 GND 1.
デバイスToshiba NTDVT006BKの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toshiba NTDVT006BKをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba NTDVT006BKの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba NTDVT006BKの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba NTDVT006BKで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba NTDVT006BKを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba NTDVT006BKの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba NTDVT006BKに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba NTDVT006BKデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。