Transition NetworksメーカーE-PSW-TX-02の使用説明書/サービス説明書
ページ先へ移動 of 16
TRANSITION NETWORKS’ POCKET SWITCH TECHNICAL SPECIFICA TIONS Standards IEEE 802.3, IEEE 802.3u Dimension 4.75" X 5.75" X 1.0" (120mm x 146mm x 25mm) Power Supply NOTE: Replace power supply only with the equivalent input rating (see below) and output rating (regulated 12VDC at 1.
100BASE-FX Cable and Connector Specifications The physical characteristics of the 100BASE-FX cable must meet or exceed IEEE 802.3u 100BASE-FX specifications.
ETHERNET CABLE SPECIFICA TIONS 10BASE-T/100BASE-TX Cable and Connector Specifications The physical characteristics of the 10BASE-T /100BASE-TX cable and connectors must meet or exceed IEEE 802.3/802.3u specifications. 10BASE-T CABLE SPECIFICATIONS Category 3 wire or better is required; category 5 wire (See 100BASE-TX) is recommended.
1. INTRODUCTION This guide is intended for the system or network administrator responsible for installing and monitoring a Transition Networks’ pocket switch. A working knowledge of local area network (LAN) operations, including familiarity with communications protocols used on interconnected LANs, is assumed.
The Evolving Ethernet Network Installing one Transition Networks’ pocket switch alone improves network performance. Installing additional Fast Ethernet equipment (and, optionally, installing additional Transition Networks’ pocket switches) can optimize network performance.
Network Flexibility The Transition Networks’ pocket switch can assist a network administrator in maintaining existing resources as the network evolves from shared legacy 10Mb/s Ethernet to switched .
4. OPERA TION The Transition Networks’ pocket switch requires no operator intervention beyond occasionally monitoring LED status indicators. POWER Steady green LED indicates connection to external AC power. NOTE: The port LED indicators provide separate data for each port.
Increasing Bandwidth by Segmenting 10BASE-T Collision Domain The Transition Networks’ pocket switch adapts to the fact that each Ethernet network device (station) is connected independently to the shared Ethernet signaling system, called the network medium.
Installing Network Cable (continued) Connecting Fiber Cable to TX/RX Connectors (100BASE-FX) Effective cable distances are determined by ambient RF noise and by signal loss in the cable. Since fiber has a low signal loss/meter and is invulnerable to RF noise, fiber can be used to extend distances.
Doubling Bandwidth by Installing Full-Duplex NOTE: The 10BASE-T specification requires two dedicated twisted copper wire pairs for data transmission and reception. This allows twisted pair copper cable to be used either in half-duplex or full-duplex mode.
Installing Network Cable (continued) Straight-Through/Crossover (10BASE - T /100BASE - T X ) The most popular wiring used today, unshielded twisted-pair copper cable, is used for 10BASE-T and for 100BASE-TX.
Increasing Bandwidth T en-fold by Installing 100BASE-TX (Fast Ethernet) Fast Ethernet, 100BASE-TX or 100BASE-FX on the Transition Networks’ pocket switch, moves signals at 100 Mb/s, ten times faster than legacy Ethernet. Legacy Ethernet and Fast Ethernet Since 100BASE-TX Fast Ethernet is an extension of the existing Ethernet IEEE 802.
The Transition Networks pocket switch can be installed to provide one 10BASE-T switched port and one 100BASE-TX switched port. Auto-Negotiation The 100BASE-TX standard includes automatic speed and duplex mode sensing as part of the Auto-Negotiation function.
Increasing Network Distance by Installing 100BASE-FX Fiber Fast Ethernet, 100BASE-FX, can be used for links to the Transition Networks’ pocket switch, particularly between buildings or where the 100 meter distance limitation of copper Fast Ethernet, 100BASE-TX, must be exceeded.
Setting DIP Switch NOTE: The Auto-Negotiation system is designed so that a twisted-pair link will not become operational until matching capabilities exist at each end.
2. SITE CONSIDERA TIONS The site for the Transition Networks’ pocket switch must provide: • AC power outlet for each Transition Networks’ pocket switch • Adequate ventilation • Standard envi.
デバイスTransition Networks E-PSW-TX-02の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Transition Networks E-PSW-TX-02をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTransition Networks E-PSW-TX-02の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Transition Networks E-PSW-TX-02の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Transition Networks E-PSW-TX-02で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Transition Networks E-PSW-TX-02を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTransition Networks E-PSW-TX-02の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Transition Networks E-PSW-TX-02に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTransition Networks E-PSW-TX-02デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
