TROY GroupメーカーTROY200 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 34
TROY200 Series Print Servers Ethernet and Wireless Models Installation and User’s Guide Part Number 40181-120 Revision A.
Notice TROY GROUP, INC. SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABIL ITY AND FITNESS OF THIS PRODUCT FOR A PARTICULAR PURPOSE. TROY shall not be liable for any errors contained in thi.
User’s Guide Document #40181-120 Rev. A i TABLE OF CONTENTS Section 1 – Product Overview Introduction ............................................................................................................................ 1-1 Package Contents .
User’s Guide Document #40181-120 Rev. A ii Appendix A – Safety and Regulatory Notices Information for United States Users ..................................................................................... A-1 Declaration of Conformity (FCC) ...
User’s Guide Document #40181-120 Rev. A 1-1 Section 1 – Product Overview Introduction TROY200 Series Print Servers allow y ou to share a printer equipped with a USB or parallel port on a wired or wireless network.
User’s Guide Document #40181-120 Rev. A 1-2 About This User’s Guide This User’s Guide contains information on system requirements, basic troubleshooting, and instructions on the following: I.
User’s Guide Document #40181-120 Rev. A 1-3 Wireless Print Server Requirements To print using a wireless print server, you will need an 802.11a, 802.11b, or 802.11g wireless network consisting of either of the following: An 802.11a, 802.11b, or 802.
User’s Guide Document #40181-120 Rev. A 1-4 Print Server Components The print server includes the following components. Detailed descriptions of these components are provided below: Power connector – The power supply cable plugs into this connector.
User’s Guide Document #40181-120 Rev. A 1-5 LED Indicators The front edge of the print server provides five Green/Orange LEDs (Light Emitting Diode) indicators for easy monitoring.
User’s Guide Document #40181-120 Rev. A 1-6 Pushbutton Functions The front edge of the print server provides a momentary pushbutton that can be used to print a test/configuration page or reset th e device to factory default settings.
User’s Guide Document #40181-120 Rev. A 2-1 Section 2 – Hardware Installation Before You Begin Before installing the print server, make sure you have installed and set up your printer as described in the documentation that came with the printer and that y our printer functions prope rly.
User’s Guide Document #40181-120 Rev. A 2-2 3. Connect the print server to your printer(s) using th e USB and/or parallel port of y our printer. For a USB connection, use a standard USB A (print server side) to B (printer side) cable. For a parallel connection, use an IEEE 1284-compliant parallel printer cable.
User’s Guide Document #40181-120 Rev. A 2-3 Verifying the Connection to the Printer 1. Verify that both the print server and the printer are powered on and ready, and that a USB or parallel printer cable is properly connected be tween the print server and printer.
User’s Guide Document #40181-120 Rev. A 3-1 Section 3 – Configuration and Management Configuration Options TROY200 Series Print Servers (wired and wireless models ) can be configured using a variety of options, some of which do not require any so ftware installation on the host PC.
User’s Guide Document #40181-120 Rev. A 3-2 HP Web JetAdmin Utility a web browser-based HP utility (e.g., Internet Explorer or Mozilla). can be downloaded from the HP web site http://www.hp.com . Configuration Console a command-line-oriented console.
User’s Guide Document #40181-120 Rev. A 3-3 Configuring the Print Server via an Ethernet Connection For Microsoft Windows operating systems, the TROY ExtendView Utility (provided on the TROY200 Series Print Server Installation CD) is the recommended m ethod of configuring one or m ore print servers on your network.
User’s Guide Document #40181-120 Rev. A 3-4 U SING THE W EB B ROWSER I NTERFACE TO C ONFIGURE TH E P RINT S ERVER (N ON -W INDOWS SYSTEMS ) : To configure the print server using non-Windows operati ng systems (e.g., Unix systems), a standard web browser (e.
User’s Guide Document #40181-120 Rev. A 3-5 U SING A THE I NTERNAL C OMMAND C ONSOLE TO C ONFIGURE TH E P RINT S ERVER : The command console can be accessed using a Telnet conn ection via an Ethernet connection. To use a Telnet connection, follow these steps: 1.
User’s Guide Document #40181-120 Rev. A 3-6 Windows Print Queue Configuration TROY recommends using the ExtendNet Connect for TCP/IP software for Windows printer port configuration (provided on the TROY200 Series Print Server Installation CD). TROY200 Series Print Servers are also compatible with Windows standard TCP/IP port and LPR ports.
User’s Guide Document #40181-120 Rev. A 3-7 Macintosh Print Queue Configuration TROY200 Series Print Servers support the AppleTal k protocol running over Ethernet (also known as EtherTalk). This capability allows Macintosh computers to print jobs to a printer simultaneously with jobs from Windows, UNIX, NetWare, and other computers.
User’s Guide Document #40181-120 Rev. A 3-8 M ACINTOSH C ONFIGURATION (OS 10. X ) 1. If you have not done so already, set the name of your computer by going to the Applications folder*, selecting System Preferences , and then Sharing . Type in the computer name in the Network Identity section (you can also set the IP address here if you want).
User’s Guide Document #40181-120 Rev. A 4-1 Section 4 – Troubleshooting Introduction This section describes procedures for troubleshooting problems you may encounter with the TROY print server, an.
User’s Guide Document #40181-120 Rev. A 4-2 If the self-test page prints successfully but you cannot prin t a job or y ou get distorted printouts, make sure the printer is set for the correct Page Descripti on Language. Most new printers support AUTO mode, which means that they will automatically switch betw een PCL and PostScript.
User’s Guide Document #40181-120 Rev. A 4-3 Troubleshooting Network Configuration Problems If you are using TCP/IP, make sure that your computer and the print server are on the same IP segment or can reach each other with a PING comm and from the host.
User’s Guide Document #40181-120 Rev. A 4-4 Troubleshooting Wireless Configuration Problems Make sure your computer’s wireless adapter a nd/or access point is configured properly and note the .
User’s Guide Document #40181-120 Rev. A 5-1 Section 5 – Where to Get Help Obtaining Technical Assistance TROY technical support is available to assist you with any questions concerning the setup, operation, or maintenance of your TROY200 Series Print Server.
User’s Guide Document #40181-120 Rev. A 5-2 Returning Products If you need to return a TROY product for any reason (failu res, incorrect shipments, etc.
User’s Guide Document #40181-120 Rev. A A-1 Appendix A – Safety and Regulatory Notices Information for United States Users This equipment has been tested and found to comp ly within the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
User’s Guide Document #40181-120 Rev. A A-2 Declaration of Conformity (FCC) According to 47CFR, Part 2 and 15 for Class B Persona l Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: TROY GROUP, INC.
User’s Guide Document #40181-120 Rev. A A-3 Information for European Users The print server and its built-in 802.11a, 802.11b, and 802.11g wireless technology is in compliance with the Class B Information Technology Equipment requireme nts and other relevant provisions of European Directive 1999/5/EC.
User’s Guide Document #40181-120 Rev. A B-1 Appendix B – Updating Firmware Loading New Firmware (Using the TCP/IP Update Utility) The TROY print server’s internal firmware can be easily updated as updates become available from TROY.
User’s Guide Document #40181-120 Rev. A B-2 3. Verify that the file(s) are correct, and then click on OK . The utility will start searching for qualified print servers present on the network. 4. When the search process is complete, click on OK to continue.
User’s Guide Document #40181-120 Rev. A B-3 5. Select the desired print server to be upgraded, click on the green icon, or click on UPDATE Æ START . The firmware update process will begin automatically as soon as the print server is ready. 6. When the print server is ready , the firmware upgr ade will begin.
User’s Guide Document #40181-120 Rev. A B-4 7. The update log will be displayed when the update process is finished. Click on Close to continue. Loading New Firmware (Macintosh OS-X) 1. If you are using the Macintosh OS-X operating syst em, download the firmware file to your desktop.
デバイスTROY Group TROY200 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TROY Group TROY200 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTROY Group TROY200 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TROY Group TROY200 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TROY Group TROY200 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TROY Group TROY200 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTROY Group TROY200 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TROY Group TROY200 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTROY Group TROY200 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
