Troy-Biltメーカー52063, 52064の使用説明書/サービス説明書
ページ先へ移動 of 24
Model 52063 - 5HP Recoil Start 52064 - 6HP Electric Start OWNER’S MANUAL T rimmer/Mower • Safety • Assembly • Features and Controls • Operation • Maintenance • Parts List GARDEN WAY INCORPORATED SAFETY FIRST! Before operating this equipment, read this Owner's Manual and the separate manual supplied by the engine manufacturer .
Dear Owner: You now own one of the finest trimmer/mowers available. It was designed to easily handle a wide variety of trimming, mowing and clearing chores. You will find the machine to be an invaluable tool in caring for your property. Please carefully read this Manual.
Figure 1-1 - Electric start model shown. Safety 1 Section 1 Trimmer Head Control Bail SP ARK ARRESTER W ARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER ST A TES Under California law, and under the.
2 Section 1: Safety 17. If using unit in wet conditions, exer- cise extreme care to prevent loss of footing. Wear footwear that will improve traction. Avoid sloping ground. Hold the handlebars with two hands and walk; never run. 18. Release the Trimmer Head Control Bail before starting the engine.
Section 1: Safety 3 SAFETY DECALS For your safety and the safety of others, various safety and operational decals are located on your unit (see below). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.
Assembly 2 Section 4 INTRODUCTION Carefully follow these assembly steps to correctly prepare your machine for use. It is recommended that you read this Section in its entirety before beginning assembly. INSPECTION AFTER DELIVERY Inspect your machine immediately after it has been delivered.
Section 2: Assembly 5 STEP 3: Attach Throttle Control Lever 1 . One end of the Throttle Control Cable (H, Figure 2-3) is attached to the engine. Gently unwind the cable from its shipping position and position the Throttle Control Lever (I) on the outside of the right han- dlebar, next to the throttle control decal.
6 Section 2: Assembly STEP 6: Connect and Charge Battery 1 . Lift and tilt debris shield (X, Figure 2- 5) forward to view battery (P). Connect the red wire (R, Figure 2-6) to the posi- tive (+) red-coded terminal on the bat- tery. Then, connect the black wire (S) to the negative ( – ) black-coded terminal on the battery.
Features and Controls 3 Section 7 OPERA TING SYMBOLS Various symbols (shown here, with word descriptions) are used on the unit. STOP FEA TURES AND CONTROLS This Section describes the location and function of the features and controls on your machine. Refer to the following Operation Section for detailed operating instructions.
INTRODUCTION Read this Section thoroughly before you start the engine. As with any piece of outdoor power equipment, getting the “ feel ” for how your machine operates and knowing the best techniques for partic- ular jobs are important to overall good performance.
USE CORRECT DIAMETER TRIMMER LINE For tougher cutting conditions, use two (or four) sections of the thicker gauge, .155" diameter extra-heavy duty line. For less demanding conditions, use two sections of the thinner gauge, .130" diam- eter heavy-duty line.
Vary Throttle Setting For Conditions The majority of trimming and mowing jobs will yield the best results if the engine throttle is set at the fastest engine speed. Less demanding jobs (and projects that require very precise cutting) may yield better results if the engine speed is backed off somewhat.
Maintenance 5 Section 11 ADJUSTING TRIMMER HEAD ENGAGEMENT The tension on the drive belt must be correct for proper operation of the trimmer head. If the tension is correct, the trimmer head will rotate when the Trimmer Head Control Bail is pulled back against the handlebar.
12 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
Section 5: Maintenance 13 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
14 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
Section 5: Maintenance 15 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
16 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
Section 5: Maintenance 17 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
18 Parts List Model 52063 & 52064 DRA WING NO. 1 1 2 3 4 5 5 5 5 5 5 7 8 9 10 11 12 13 17 17 17 16 20 21 22 23 24 25 15 18 19 14 14 6 6.
Parts List 19 Model 52063 & 52064 1 1917765 Debris Guard ............................................ 1 2 1918082 Decal-Logo (B) ......................................... 1 1904401 Decal-Logo (A) ......................................... 1 3 1915290 Push-in Fastener .
20 Parts List Model 52063 & 52064 DRA WING NO. 2 See DRAWING NO. 1 See DRAWING NO. 3 See ACCESSORIES AND KITS 2 2 1 1 3 3 4 7 8 9 10 11 12 13 14 15 16 27 17 18 22 23 24 25 26 18 18 19 20 21 6 1 1917778 Wheel/Tire Assembly .........................
Parts List 21 Model 52063 & 52064 DRA WING NO. 3 1 4 5 2 3 6 6 8 7 9 12 13 13 13 14 15 16 14 10 11 1 1918283 Upper Handlebar (Incl. Refs. 2 & 3) ....... 1 2 1915889 Decal – Bail Engage/Disengage ................ 1 3 1918304 Decal – Throttle .
1905693 (5/01) Printed in U.S.A. © 2001 Garden Way Incorporated CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and informational bulletins.
デバイスTroy-Bilt 52063, 52064の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 52063, 52064をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 52063, 52064の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 52063, 52064の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 52063, 52064で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 52063, 52064を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 52063, 52064の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 52063, 52064に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 52063, 52064デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
