TV Oneメーカー1T-C2-250の使用説明書/サービス説明書
ページ先へ移動 of 81
1T - C2 Series Operation Manual.
1T-C2 S ERIES O PERATION M ANUAL.
1T-C2 S ERIES O PERATION M ANUAL Table of Contents 1 DISCLAIMER ................................ ................................................................ 1 1.1 Regulatory Agency Acceptance.................... ............ .................... .
1T-C2 S ERIES O PERATION M ANUA L 8.6.2 DVI Source Menu Items .................... ............ .................... ............ .................... 37 8.6.3 RGB Source Menu Items .................... ................................ ............ ..
1T-C2 S ERIES O PERATION M ANUA L 12.14 No video present from the UTP output. .................... ............ .................... ......... 68 13 RETURN PROCEDURE ................................ ................................ ............. 69 13.
1T-C2 S ERIES O PERATION M ANUAL 1 1 DISCLAIMER This product is intended for professional and/or home use. This product is not intended for use in a medical environment and does not have the required certifications for such use.
1T-C2 S ERIES O PERATION M ANUAL 2 Caution: This equipment is intended for use in the manner prescribed in the Instruction Manual. Any user changes or modifications not expressly approved by TV One Multimedia Solutions could void the user’s authority to operate the equipment.
1T-C2 S ERIES O PERATION M ANUAL 3 2 IMPORTANT SAFETY INSTRUCTIO N To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference. To reduce the risk of electric shock, do not remove the cover from the unit.
1T-C2 S ERIES O PERATION M ANUAL 4 2.5 Venti lation Slots and openings in the sides of the unit are provided for ventilation. To ensure reliable operation, avoid obstruction of these openings and ensure the unit is installed in a well -ventilated area.
1T-C2 S ERIES O PERATION M ANUAL 5 2 IMPORTANT: CONSIGNES DE SECURITE Afin de tirer le m eilleur de ce produit, merci de lire attentivement ce manuel. Gardez -le dans un endroit sûr pour pouvoir le consulter à nouveau. Afin de réduire le risque de choc électrique, ne retirez pas l’unité de sa protection.
1T-C2 S ERIES O PERATION M ANUAL 6 L’installation de cette unité doit se faire dans un endroit frais et sec, éloigné de sources excessives de chaleur, de vibrations, de poussière, d’humidité et de froid. 2.5 Aération Les rainures et les ouvertures sur les cotés de l’unité servent à l’aérer.
1T-C2 S ERIES O PERATION M ANUAL 7 2 INSTRUCCIONES IMPORTANTES DE SEGURIDAD Para sacar el mejor provecho de este producto, léase este manual con detenimiento. Guárdelo en un lugar seguro para poder hacerle referencia en el futuro. Para reducir el riesgo de calambre, no quite la cub ierta del aparato.
1T-C2 S ERIES O PERATION M ANUAL 8 2.4 Ubicación Este aparato se debe instalar en un lugar seco y fresco, lejos de fuentes de calor excesivas, la vibración, el polvo, la humedad y el frío. 2.5 Ventilación El aparato viene provisto de ranuras y agujeros en los lados para la ventilación.
1T-C2 S ERIES O PERATION M ANUAL 9 2 WICHTIGE SICHERHEITSVORSCHRIFTEN Lesen Sie diese Bedienungsanleitung bitte sorgfältig, um Ihr Produkt optimal nützen zu können, und bewahren Sie sie zum später en Nachschlagen an einem sicheren Ort auf. Entfernen Sie bitte keinesfalls die Abdeckung, um der Gefahr eines Stromschlags vorzubeugen.
1T-C2 S ERIES O PERATION M ANUAL 10 2.3 Aufstellung Das Gerät sollte an einem kühlen, trockenen Ort aufgestellt werden, fern von übermäßiger Wärme, Vibrationen, Staub, Feuchtigkeit und Kälte. 2.5 Belüftung Seitliche Schlitze und Öffnungen sorgen für die Belüftung des Geräts.
1T-C2 S ERIES O PERATION M ANUAL 11 2 BELANGRIJKE V EILIGHEIDSINSTRUCTIES Lees deze handleiding zorgvuldig door om het beste uit uw product te halen. Bewaar het op een veilige plek voor raadpleging in de toekomst. Haal nooit het omhulsel van de eenheid af, dit om de kans op een elektrische schok te verminderen.
1T-C2 S ERIES O PERATION M ANUAL 12 2.4 Plaatsing Deze eenheid moet geïnstalleerd worden op een koel e droge plaats, uit de buurt van bronnen van extreme hitte, vibraties, stof, vocht en kou. 2.5 Ventilatie De sleuven en openingen aan de zijkant van de eenheid zijn voor ventilatie.
1T-C2 S ERIES O PERATION M ANUAL 13 3 DEVICE SUMMARY 3.1 Device Capabilities The 1T-C2 series uses the proprietary CORIO ® 2 Engine to perform its functions, being the second generation of the successful CORIO ® products.
1T-C2 S ERIES O PERATION M ANUAL 14 PC/HD Scaler This unit allows computer / high-definition video scaling from one resolution to another – for example, 720p to 1080i, or VGA to XGA, etc.
1T-C2 S ERIES O PERATION M ANUAL 15 4 PRODUCT IMAGES Your 1T -C2 product should look like one of the units below. Each unit has a different main function (Down Converter or Video Scaler) and a subsequently different ability to process video signals.
1T-C2 S ERIES O PERATION M ANUAL 16 5 FRONT PANEL CONTROLS The range of buttons on the front of the unit provides the user with quick access for selecting a variety of inputs and features. Since all the units in the 1T -C2 series are different, not all of the descriptions below will be applicable to the unit in question.
1T-C2 S ERIES O PERATION M ANUAL 17 5.2 MENU and buttons The on -screen display (OSD) is controlled from the front panel by using these buttons. MENU will activate the OSD, whilst the and arrowed keys will allow different menu items to be selected and adjusted – this is detailed in a later section.
1T-C2 S ERIES O PERATION M ANUAL 18 All stored settings except resolutions are lost when the unit is reset. A Firmware update is the on ly way to perform a complete factory reset (including resolution data).
1T-C2 S ERIES O PERATION M ANUAL 19 6 VIDEO INPUTS AND OUT PUTS The units have different video inputs and outputs depending on your model, and with the PC/HD output being either scaled, or just as a loop - through from the PC/HD input.
1T-C2 S ERIES O PERATION M ANUAL 20 RGBS (separate sync at TTL levels) YUV/YPbPr (including tri -level). However, please note that on some units such as Down Converters, the PC/HD output is there just to loop the PC image through to the PC monitor.
1T-C2 S ERIES O PERATION M ANUAL 21 7 INFRA - RED REMOTE CONTROL Your unit is compatible with an optional infra-red remote control as shown below: Resets back to power -on defaults Stores current Selects input: settings 1/2/3=RGB/CV/YC Enables Keyer Enables Lock & Mix mode Fades in/out Starts AutoSet Locks the IR & panel buttons (Not used.
1T-C2 S ERIES O PERATION M ANUAL 22 8 MENU LAYOUT AND SETT INGS ADJUSTMENT From here on, we’ll be looking at the menu structure employed in the series and, more importantly, the individual menu items that allow you to take advantage of the power of the unit.
1T-C2 S ERIES O PERATION M ANUAL 23 The first is the ‘welcome’ display shown above indicating the model of the unit. Moving to the next menu item displays the firmware information screen (the numbers on your unit will be different to those shown).
1T-C2 S ERIES O PERATION M ANUAL 24 This menu item allows the lock mode to be selected and the lock source to be defined. The top line of the display shows the current detected resolution of the selected lock source (RGB1 in this example).
1T-C2 S ERIES O PERATION M ANUAL 25 Your unit can handle a very wide array of inputs and convert them all to a single output signal with defined characteristics. This output resolution will remain in place until changed or it may be overridden by the lock mode and source.
1T-C2 S ERIES O PERATION M ANUAL 26 but the output is not cur rently encrypted. scaling. Rep. active The repeater unit (e.g. scaler) attached is capable of HDCP, and the output from the unit is encrypted. As the DVI output is HDCP encrypted, then a HDCP- encrypted source can be selected for scaling.
1T-C2 S ERIES O PERATION M ANUAL 27 This menu item is only available on certain units when the Output resolution is set to PAL or NTSC. With this you can change the output filtering system to increase or decr ease the image sharpness. In general, high sharpness can result in increased colour disturbance.
1T-C2 S ERIES O PERATION M ANUAL 28 Changing this option, sets the amount of picture magnification you wish to use for the window Source. You are provided with the options to zoom the image from 100% to 1000% (10x zoom).
1T-C2 S ERIES O PERATION M ANUAL 29 Note that some units do not have the [On] entry – this is only for units with a PIP button on the front, with turns this entry On and Off. On these units, thi s feature is ‘Off’ by default, so that the full image size of 100% is used.
1T-C2 S ERIES O PERATION M ANUAL 30 Off Disables flicker reduction (sharpest mode). Low Suitable for most input sources. Med. Enough for most situati ons such as thin line drawings High Highest amount of flicker reduction. Will cause loss of vertical detail in some images .
1T-C2 S ERIES O PERATION M ANUAL 31 In ‘Pixel’ mode, the user has direct access to pixel and line-accurate scaling functions. This lets the user specify the exact co-ordinates and size of the source image (within the video source), and the position and size of where this is placed in the output video signal.
1T-C2 S ERIES O PERATION M ANUAL 32 8.4.3 ‘Aspect adjust’ = ‘Pixel’ These menu items work together to specify the exact co-ordinates and size of the source image (within the video source) and the position and size of where this is placed in the output video signal – in other words the ‘In’ and ‘Out’ positions and sizes.
1T-C2 S ERIES O PERATION M ANUAL 33 This menu item is only present on single -channel scalers – dual -channel scaler s have the layer priority set within the ‘Adjust Windows’ menu . This menu item allows you to swap the foreground and background images when Lock mode is set to Lock & Mix.
1T-C2 S ERIES O PERATION M ANUAL 34 sometimes 51%. Increasing the softness value will broaden the range of keyed colors s o that the keying of images varies depending on how close a color is to the keyed-out range. The Y Key invert changes the keying characteristics with respect to what colors of the foreground image you wish to ‘key out’.
1T-C2 S ERIES O PERATION M ANUAL 35 8.6.1 Menu items common to all inputs This menu item will be used to correct the aspect ratio of the video s ource when converted into the final output resolution. The following table details what happens in the available modes: Setting Result Fill (default) The source is stretched to fill the output.
1T-C2 S ERIES O PERATION M ANUAL 36 If an external audio switcher is connected via the OPTION bus, then this menu item selects the desired Audio input for use with the active video source, allowing an audio -follow -video function.
1T-C2 S ERIES O PERATION M ANUAL 37 maximum movement within an image. Your unit provides some tools to minimize the effects of de -interlacing of an image. The following options are available for this menu item: Mode Function Normal /weave The two interlaced fields are simply combined /weaved together.
1T-C2 S ERIES O PERATION M ANUAL 38 If turned ‘On’, and a HDCP -compliant display or device is attached to your unit’s DVI output, then HDCP encrypted sources can be used. The following table summarizes the message given in brackets: Status message Description Effect Inactive HDCP is not active at the DVI connector.
1T-C2 S ERIES O PERATION M ANUAL 39 If you change this value, you’ll need to store your settings and then re-boot the CORIO2 unit at least once to ensure that the DVI source sees that the EDID data has changed. It should also be noted that some graphic cards will require your PC to be re - booted before they see that a change has occurred.
1T-C2 S ERIES O PERATION M ANUAL 40 pixel phase adjustment allows you to change the position (from 0 to 31) where the pixels are sampled, relative to the horizontal sync signal. To make this adjustment, select an RGB source and then provide an image from that source with fine detail, preferably with very sharp vertical lines.
1T-C2 S ERIES O PERATION M ANUAL 41 Saturation is the amount of color present in the image. Hue is the color “tint” parameter and the adjustment range is +90 degrees through to -90 degrees with 0 being the default. Within limits, you can enhance or soften th e appearance of detail within an image.
1T-C2 S ERIES O PERATION M ANUAL 42 Important Cautionary Information DO NOT ADJUST THESE ITEMS UNLESS YOU’RE CERTAIN YOU KNOW WHAT YOU’RE DOING! THE ONLY METHOD TO UNDO CERTAIN CHANGES IS TO UPDATE THE FIRMWARE. TRY USING THE AUTOSET, SHRINK, SHRINK POS, TL & BR ADJUSTMENTS FIRST .
1T-C2 S ERIES O PERATION M ANUAL 43 The H.freq.fine (Horizontal Sync Frequency) adjustment provides the option for changing the Horizon tal Sync timing Frequency in 1 Hz steps . Use this option to fine tune after using the course adjust. Please note that the internal sync generator may be unable to generate the exact frequency you want.
1T-C2 S ERIES O PERATION M ANUAL 44 respect to the Horizontal Sync pulse and the width of the Back Porch have a direct bearing on where the active (visible) portion of the image begins. Do not attempt this adjustment without monitoring the results with an oscilloscope.
1T-C2 S ERIES O PERATION M ANUAL 45 The first section, “SW”, is the version of the software that is installed on your unit. You can update software via the User Support web site (procedure to be described later in this manual) and the updates are currently free of charge.
1T-C2 S ERIES O PERATION M ANUAL 46 of the screen edge between Low, Medium, High and V.high. Medium is the default level, which is recommended for normal use (Windows-type images, etc.) This parameter controls whether the ‘welcome’ screen is displayed or not on power up for units with an on -screen display – it can be disabled as required.
1T-C2 S ERIES O PERATION M ANUAL 47 If your units supports Log os or Still Images / Testcards then this screen will display how many ar e present in t he memory of the units. Power Cycles refers to how many times the unit has been powered since it left the factory.
1T-C2 S ERIES O PERATION M ANUAL 48.
1T-C2 S ERIES O PERATION M ANUAL 49 9 RS232 PORT 9.1 Connection Your unit is fitted with a standard ‘D9’ plug or socket allowing it to be controlled from a computer or other type of terminal or console with a similar interface. Most computers fitted with an RS232 port, known as a ‘COM’ port, will have a ‘D9’ plug on them.
1T-C2 S ERIES O PERATION M ANUAL 50 10 RS232 / IP CONTROL S PECIFICATION PLEASE NOTE: Not all units support RS232 and/or IP (Ethernet) communications – check to see if this feature is present on your unit. This section outlines how to control a unit via an RS232 or Ethernet link (if fitted to your unit), using ASCII-based commands.
1T-C2 S ERIES O PERATION M ANUAL 51 The ACK flag will be returned as 0 if the command is invalid for some reason – for example a bad FUNCTION, WINDOW, OUTPUT or PAYLOAD value. An ACK=0 message will be otherwise identical to the one you sent, so you know exactly which message has the error.
1T-C2 S ERIES O PERATION M ANUAL 52 returned means message was okay. ACK=0 returned means an error was present in the message. Bit 5 = 0 Reserved for future use. Bit 4 = 0 Reserved for future use. Bit 3 = 0 Reserved for future use. Bit 2 = 1 This bit *must* be se t .
1T-C2 S ERIES O PERATION M ANUAL 53 CS ASCII -hex byte that is the (check) sum of all previous bytes (excluding the SOP 'F' character). E.g. The command F0400410082000001C8 has the checksum of 04+00+41+00+82+00+00+01=C8, so the complete command to send is F0400410082000001C8.
1T-C2 S ERIES O PERATION M ANUAL 54 Adjust outputs Output enable 170 0=Blanked, 1=Active Lock source (connector ) 149 0x10 to 0x1F = RGB1 to RGB16 0x30 to 0x3F = CV1 to CV16 0x40 to 0x4F = YC1 to YC16.
1T-C2 S ERIES O PERATION M ANUAL 55 3 = 14:9 Letterbox top 4 = 16:9 Letterbox centre 5 = 16:9 Letterbox top 6 = >16:9 Letterb ox centre 7 = 14:9 Full format 8 = 16:9 Full format Take 11E 0 ->1 = Perform a Preview -> Program transition Audio amp.
1T-C2 S ERIES O PERATION M ANUAL 56 In (top-left H) 21B In (top-left V) 21D In (H size) 21C In (V size) 21E Out (top -left H) 21F Out (top -left V) 221 Out (H size) 220 Out (V size) 222 Aspect change 190 0.. 2 = Normal, Letterbox, Pillarbox Aspect a djust 102 0.
1T-C2 S ERIES O PERATION M ANUAL 57 E.blnd gamma H 188 1..150 1=0.01, 150=1.50 E.blnd gamma V 18D 1..150 1=0.01, 150=1.50 E.blnd comp cent 198 0..99 E.blnd c omp side 19D 0..99 Logos (on certain models only) Logo enable 12B 0..1 = Off, On Logo number 143 0.
1T-C2 S ERIES O PERATION M ANUAL 58 Audio vol 10..FF 0CF -16..15 ( -16=Mute) Bal 10..FF 0D1 -15..15 On source loss (was Deglitch) 10..5F 0A3 0=Show, 1=Freeze, 2=Blue, 3=Black, 4=Remove Source stabl e (read only) 22A 0=Unstable, 1=Stable Input pixel phase 10.
1T-C2 S ERIES O PERATION M ANUAL 59 Switching fade time 0F5 0 (off) to 50 (5.0 seconds) Wipe type 145 0 = Left -> Right 1 = Right -> Left 2 = Up -> Down 3 = Down -> Up 4 = Diagonal 5 = Diamond Wipe Size 146 10..2000 Audio Control (S2 -106AD Only) Sample frequency 191 0.
1T-C2 S ERIES O PERATION M ANUAL 60 Resolutions 0D8 Read only Number of Still Images / Testcards 0D9 Read only Number of logos 14F Read only Board temp. (deg.C) 0CD Read only Air temp. (deg.C) 148 Read only Regulators temp.(deg.C) 147 Read only PLD temp.
1T-C2 S ERIES O PERATION M ANUAL 61 F 84 00 42 00 86 - ?? CR F 44 00 42 00 86 000064 70 CR Set baud to 9600 Reply is at 9600 baud F 04 00 42 00 AB 000000 F 0 CR F 44 00 42 00 AB 000000 30 CR Set 1A Zo.
1T-C2 S ERIES O PERATION M ANUAL 62 Read number of items currently stored in Preset 2 Returned packet indicates 4 items available to read F 84 01 42 00 F4 - BB CR F 44 01 42 00 F4 00002 FC CR Read the.
1T-C2 S ERIES O PERATION M ANUAL 63 SOP CMD CHA WIN OUT FUN PAY CS EOP SOP CMD CHA WIN OUT FUN PAY CS EOP Restore F 04 05 42 00 F1 000000 3C CR F 44 05 42 00 F1 0000 00 7C CR Run macro 1 F 04 00 42 00.
1T-C2 S ERIES O PERATION M ANUAL 64 11 COMMON OPERATIONS This section provides step by step instructions for some common operations. 11.1 Operation of the Keyer Some units come equipped with a very powerful Luminance and Chrominance Keyer.
1T-C2 S ERIES O PERATION M ANUAL 65 to decrease the ‘min’ values and increase the ‘max’ values to broaden the range of colors keyed out. At this point, only the key color should remain transparent.
1T-C2 S ERIES O PERATION M ANUAL 66 12 TROUBLESHOOTING AND TECHNICAL SUPPORT If problems are experienced, please read through the symptom topics below in order to resolve the problem. After doing so, if you still need to, contact Technical Support at http://www.
1T-C2 S ERIES O PERATION M ANUAL 67 12.4 There is excessive flicker on the Output. Try using a different Flicker re duction mode. Turning the contrast down and the brightness up on the output device can have a large effect on flicker. Or try adjusting the brightness and contrast of the source input by selecting the Input adjust menu.
1T-C2 S ERIES O PERATION M ANUAL 68 12.11 The RGB input is selected but the image is rolling or pink. Check the Adjust sources menu and confirm that the input type and sync method is set correctly. (Having YUV input selected, instead of RGBHV often causes this problem).
1T-C2 S ERIES O PERATION M ANUAL 69 13 RETURN PROCEDURE Before returning your unit for repair, there are several checks you can make yourself to make sure the problem is actually caused by a failure.
1T-C2 S ERIES O PERATION M ANUAL 70 Please clearly state the return number on the outside packaging and on any accompanying documentation. This will greatly speed up processing. IMPORTANT: DO NOT return a unit for warranty repair without first obtaining a Return Authorization Number.
1T-C2 S ERIES O PERATION M ANUAL 71 14 WARRANTY POLICY LIMITED WARRANTY – With the exceptions noted in the next paragraph, TV One warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase.
1T-C2 S ERIES O PERATION M ANUAL 72 15 CONNECTOR PINOUTS 15.1 HD15 connector 1. Red / Pr / R -Y 2. Green / Y 3. Blue / Pb / B -Y 4. ID2 (input & output linked) 5. GND 6. GND 7. GND 8. GND 9. No connection 10. GND 11. GND on input, pulled high on output (used for auto -termination) 12.
1T-C2 S ERIES O PERATION M ANUAL 73 16 SPECIFICATIONS See product front and rear diagrams for details of product I/O. Not all units in the series have all the inputs and outputs listed here.
1T-C2 S ERIES O PERATION M ANUAL 74 PC Resolutions: any up to 2048x2048 (user adjustable) HDTV Resolutions: any up to 1 080p Vertical Refresh Rate: any to 250Hz 16.
1T-C2 S ERIES O PERATION M ANUAL 75 16.10 Power Requirement External power supply: 12V DC @1A maximum. Actual current consumption varies between units. Internal over -voltage & over -current protection. Full PSU specification: 12v DC regulated 1Amp PSU with a 2.
1T-C2 S ERIES O PERATION M ANUAL 76 17 CONTACT INFORMATION Should you have and questions or require assistance with this product in areas not covered by this manual, please contact TV One at the appro.
デバイスTV One 1T-C2-250の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TV One 1T-C2-250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTV One 1T-C2-250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TV One 1T-C2-250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TV One 1T-C2-250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TV One 1T-C2-250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTV One 1T-C2-250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TV One 1T-C2-250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTV One 1T-C2-250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
