UNICOM ElectricメーカーDynaGST/1602Gの使用説明書/サービス説明書
ページ先へ移動 of 17
16 Port 10/100/1000Base-T Gigabit Ethernet Switch with two SFP (mini) GBIC Slots DynaGST/1602G U SER’S M ANU AL PN: GEP-33216T.
Content 1. Introduction .............................................................. 1 Features ..................................................................... 2 Package Contents ...................................................... 3 2. Hardware Description .
.
1 1. Introduction Gigabit Ethernet over copper technology is a proven cost-effective way for network equipment to be upgraded from Fast Ethernet to Gigabit speeds. The need of expensive fiber optic cabling for Gigabit speeds is eliminated by using standard 4-pair Category 5e copper cabling.
2 Features Compatible with IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3z Gigabit fiber and IEEE802.3ab 1000Base-T 16 Port Gigabit switch with two Mini SFP GBIC ports Automatic MDIX for all ports 4K entry MAC address table 2Mbit Memory buffer IEEE802.
3 Package Contents DynaGST/1602G Gigabit Ethernet switch Power Cord Four Rubber Feet User Manual DynaGST/1602G Gigabit Ethernet switch Power Cord User Guide Rubber Feet Figure 1-1. Package Contents Compare the contents of your DynaGST/1602G Gigabit Ethernet switch package with the standard checklist above.
4 2. Hardware Description This Section describes the hardware of the DynaGST/1602G Gigabit Ethernet switch. The physical dimensions of the DynaGST/1602G Gigabit Ethernet switch is: 440 x 224 x 44 mm (.
5 [Note] When the Mini GBIC module is installed, the Mini GBIC (Gigabit fiber) ports ha ve higher priority than the Gigabit copper ports and supercede them. It doesn’t matter if the Gigabit copper port is connected before or after the Mini GBIC port is connected.
6 Figure 2-3. LED Indicators LED Status Description Green Power On Power Off Power is not connected Green Port is operating at 1000Mbps. 1000 Off No device attached or in 10/100Mbps mode Green Port is connecting with the device. Blinking Port is receiving or transmitting data.
7 Mini GBIC LED The two Mini GBIC ports have two LED indicators each – LNK and ACT. The following table provides descriptions of LED status. Figure 2-4. Mini GBIC Port LED Indicators LED Status Description Green Port is connecting with device. LNK Off No device attached.
8 3. Installation Set the Switch on a sufficiently large flat space with a power outlet nearby. The surface should be clean, smooth, level, and sturdy. Ensure there is enough clearance around the Switch to allow air circulation and the attachment of the power cord and cables.
9 4. Network Application This section provides you a sample of network topology in which the DynaGST/1602G is used. In general, the DynaGST/1602G Gigabit Ethernet switch is designed as a high-bandwidth backbone switch.
10 5. Troubleshooting The Switch can be easily monitored through panel indicators to assist in identifying problems. This section describes common problems you may encounter and where you can find possible solutions. Diagnosing LED Indicator If the Link indicator does not light up after connection, check whether the network interface (e.
11 Cabling RJ-45 ports: Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100m. of Category 3,4 or 5 cable for 10Mbps connections, 100m. of Category 5e cable for 100Mbps connections, or 100m. of 4-pair Category 5e copper cabling for 1000Mbps connection.
12 6. Technical Specification The following table provides the technical specification of the DynaGST/1602G Gigabit Ethernet switch. Standard IEEE802.3 10Base-T IEEE802.
13 LED System: Power Per RJ-45 port: 1000Mbps, Link/Activity, Full duplex/ collision Mini GBIC port: Link and Activity Power Supply Internal power supply, AC 100~240VAC, 50/60 Hz Power Consumption 60W.
908 Canada Court City of Industry , C A 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 F ax: 626.964.7880 www .unicomlink.com e-mail: info@unicomlink.
デバイスUNICOM Electric DynaGST/1602Gの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
UNICOM Electric DynaGST/1602Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUNICOM Electric DynaGST/1602Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。UNICOM Electric DynaGST/1602Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。UNICOM Electric DynaGST/1602Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
UNICOM Electric DynaGST/1602Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUNICOM Electric DynaGST/1602Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、UNICOM Electric DynaGST/1602Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUNICOM Electric DynaGST/1602Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
