UnidenメーカーEXA 7950の使用説明書/サービス説明書
ページ先へ移動 of 36
H:...reprint 8-13-99EXA7950.vp Tue Aug 17 15:32:30 1999 Color profile: Disabled Composite Default screen.
CO N T E N T S OF Y OUR O WNER’S MANU AL CONTENTS Controls and Functions .......................... Back Cov er Fold-out Introduction ...................................................1 • W elcome .................................................
Introduction WELCOME Congratulations on your pur chase of the Uniden EXA7950 cordless telephone and answering system. This phone is designed and engineered to exacting standards f or reliability , long life, and outstanding performance.
INCLUDED IN Y OUR P A CKA GE Also included: • This Owner’s Manual • Precautions and Im portant Safety Instructions/W arranty Information • Registration Car d 2 Handset Base A C Adapter Recharg eable Batter y T elephone Cord W all Mount Adapter TIP T o get the most from your phone, please read this owner’s manual thoroughly .
Installing and Adjusting YourPhone DESK/TABLETOP INST ALL A TION 1) Plug the A C adapter cord into the 9 VDC in put jack on the back of the base. 2) Wrap the A C adapter cord around the strain relief notch. 3) Plug the AC adapter into a standard 1 20 V AC w all outlet.
7) Set the base on a desk or tabletop, and place the handset into the base as shown. Then, raise the antenna to a vertical position. W ALL INST ALL A TION ▼ Standard wall plate mounting This phone can be mounted on any standard A T&T or GTE wall plate.
5) Plug one end of the telephone cord into the TEL LINE jack on the back of the base, then plug the other end into a standard telephone jack. 6) Line up the mounting slots on the base with the mounting posts on the wall, then push in and down until the phone is firmly seated.
▼ Direct wall mounting If you don’t hav e a standard wall plate, y ou can mount your phone directly to the w all. Before doing this, consider the follo wing: • Select a location away fr om electrical cables, pipes, or other items behind the mounting location.
5 ) Put the AC adapter cor d inside the molded wiring channel, then wrap the A C adapter cord ar ound the strain relief notch. Plug the A C adapter into a standard 1 20 V A C w all outlet. 6) Plug one end of the telephone cord into the TEL LINE jack on the back of the base, then plug the other end into a standard telephone jack.
9) Flip the retainer from fr ont to back, then slide it back into the slot so that the lip of the retainer f aces up and the ov al is at the bottom of the retainer . This will hold the handset in place. INSTALLIN G THE HANDSET BATTER Y P A CK 1) Remo ve the handset batter y co ver .
▼ Low batter y indicator When the battery pack is ver y lo w and needs to be charged, the phone is pr o- grammed to eliminate functions in order to sav e pow er . If the phone is not in use, the talk/batt LED flashes every three seconds. If the phone is in use, the ta lk/ ba tt LED flashes every three seconds and the handset beeps.
SETTING THE PULSE/TONE SWITCH Be sure the PULSE/T ONE switch is in the T ONE position unless your local phone system uses pulse dialing. ADJUSTING THE RIN GER CONTROLS ▼ Handset ringer tone and ring er volume When the phone is either charging or in standby mode, pressing the volume k ey on the handset selects the handset ring er volume and tone.
A UTOMA TIC DIGITAL CODE SECURITY T o prevent other parties from making unauthorized calls on y our phone line, a digital code was added to the EXA7950. Y our phone’s handset and base share this code, which is randomly set each time y ou place the handset in the charging cradle.
Using YourNew Phone MAKING AND RECEIVIN G C ALLS Handset On Base Handset Off Base T o answer a call Pick up the handset, or press s p eak er on the base. Press any button or pr ess speaker on the base.. T o make a call 1) Pick up the handset. 2) Press talk .
STORING A PHONE NUMBER IN MEMOR Y Y our EXA7950 phone has 1 0 memor y locations f or storing important telephone numbers. 1) Remo ve the handset from the base. 2) Press mem. Y ou hear a beep and the talk/batt LED blinks. 3) Enter the phone number , up to 1 6 digits.
▼ One-touch priority dialing Y our phone is equipped with three “One- T ouch Priority” keys f or instant dialing. Y ou cannot store phone numbers directly into m1 , m2 or m3 . They are only used to dial phone numbers stored into memory locations 1, 2 and 3.
REDIAL The redial k ey redials the last number dialed. The r edialed number can be up to 32 digits long. TONE If you ar e dialing in the pulse mode and need to enter tone digits, press tone to enter the digits. Once the call has ended, the tone mode is canceled and pulse dialing resumes.
Setting Up the Integrated Answering Device THE INTEGR ATED ANSWERING DEVICE The EXA7950 has a built-in answering system that answ ers and records incoming calls.
TURNING THE ANSWERIN G SYSTEM ON/OFF 1) T o turn the answering system on, press answer on/off . A beep tone will sound and the current outgoing message will play on the base speak er . A second beep tone will sound after the outgoing message plays. The messag e counter LED lights to indicate that the unit is ready to answ er calls.
4) Press skip or repeat until you hear the curr ent hour setting. Numbers 1 through 1 2 display on the base as each hour is announced. 5) Press cloc k again to select the correct hour . 6) Press skip or repeat until you hear the curr ent minute setting.
2) When you ar e finished recording y our message, pr ess greeting again. A tone sounds and your messag e plays back on the base speaker . ▼ Announce only f eature The Announce Only feature plays a pr erecorded outgoing message or your o wn personal outgoing message, but it will not allow the caller to leave a messag e.
SELECTING A PIN CODE T o play your messages fr om a remote location, you will need to enter a two-digit P ersonal Identif ication Number (PIN) code (00-99). T o select a PIN, perform the f ollowing steps: 1) On the base, press and hold the pin button.
SETTING THE TOLL S A VER SWITCH The ring time/toll saver switch allows y ou to set the number of rings the caller hears befor e your answ ering system plays your outgoing messag e. Y ou can set the switch to answer after two rings or after four rings.
Using the Integrated Answering Device PL AYIN G Y OUR MESSA GES The base LED shows the number of total messag es on the display . If the display is blinking, then there are new messag es waiting f or you. The EXA7950 is designed to play your new messag es f irst.
2) Af ter a message has play ed for a f ew seconds, press repeat to replay the message. 3) Press play/stop at any time to stop reviewing y our messages and return to standby . The messag e counter LED shows the total number of messages still on the system.
DELETING A MESS AGE 1 . Press play/stop to review your messag es. 2. If y ou decide to delete a messag e, press and hold delete anytime during the message. The system beeps and immediately goes to the next message. 3. After you have play ed all of your messag es, a long tone sounds on the base speak er .
2) Release voice memo and speak into the microphone. 3) When you hav e f inished, press play/stop or voice memo to stop recording. The system r eturns to standby . RECORDING A CONVERS ATION Y ou can record up to a 1 5 minute conversation while you ar e using your phone.
4) Y ou may continue to listen to your messag es, or you may select a command from the f ollowing chart: 5) After all of your messages hav e played, you will hear intermittent beeps indicating that the system is in the command waiting mode. Y ou may enter another command at this time from the chart abov e.
REMOTE ROOM MONITOR Y ou can call your answ ering system from any touch-tone phone and monitor sounds in the room where y our base is installed. 1) Call your telephone number . 2) During the outgoing message playback, pr ess # follo wed by your PIN code.
Troubleshooting QUICK REFERENCE CHART If your phone is not perf orming to your expectations, please tr y these simple steps first. PROBLEM SUGGESTION The charge light w on’t come on when the handset is placed in the base. • Mak e sure the A C adapter is plugged into the base and wall outlet.
PROBLEM SUGGESTION The handset doesn’t ring or receiv e a pag e. • The Nick el-Cadmium battery pack may be weak. Charg e the batter y on the base unit for 1 5-20 hours. • The handset may be too far aw ay from the base unit. • Place the base unit away fr om appliances or metal objects.
PROBLEM SUGGESTION Cannot access remote call-in features fr om another touch-tone phone. • Mak e sure y ou’re using the corr ect PIN number . • Mak e sure that the touch-tone phone you’r e using can transmit the tone for at least tw o seconds.
Specifications GENER AL The EXA7950 complies with FCC P ar ts 1 5 and 68. Fr equency control: PLL Modulation: Fr equency Shift Keying Operating temperatur e: 0º to 50º C (+32º F to +1 22º F) BASE Transmit F requency: 925.997 to 927 .947 MHz Receiv e Frequency: 902.
At U niden, we’ll tak e care of you! If you need an y assistance with this product, please call our Customer Hotline at: 1-800-297- 1 023 Please do not return this product to the place of pur chase .
AND FUNCTIONS CONTR O LS.
T H A N K Y O U FOR PUR CHASIN G A UNIDEN PHONE! Co v ered under one or mor e of the follo wing U.S. patents: 4,5 1 1,7 6 1 4,523,058 4,595,795 4,797 ,9 16 5,38 1,460 5,426,690 5,434,905 5,49 1 ,7 45 .
デバイスUniden EXA 7950の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Uniden EXA 7950をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUniden EXA 7950の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Uniden EXA 7950の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Uniden EXA 7950で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Uniden EXA 7950を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUniden EXA 7950の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Uniden EXA 7950に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUniden EXA 7950デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
