UnidenメーカーPCD1080の使用説明書/サービス説明書
ページ先へ移動 of 41
Precautions Before you read anything else, please observe the following: Rechargeable Nickel-Cadmium Battery Warning This equipment contains a Rechargeable Nickel-Cadmium Battery. Cadmium is a chemical known to the state of California to cause cancer.
1 TABLE OF CONTENTS PCD2000A Controls ......................................................2 PCD2000A Liquid Crystal Display ...............................3 Safety Informatin for Wireless Handheld Phones ......4 Important Information ...............
PCD2000A Portable Cellular Phone Controls 2 1. Antenna 2. Earphone 3. Display 4. Scroll Up/ Volume Up 5. Send Key (Call Origination, Flash Key) 6. Memory Process/Recall Key 7. Alphanumeric Keypad 8. Asterisk Key (Phone Number Review) 9. External Charger Jack 10.
PCD2000A Liquid Crystal Display 3 1 8 2 34 5 6 7 1. 20 Character Display 2. Signal Strength Indicator 3. Appears when out of Service Area or No Signal 4. Indicates System in use (A or B) 5. Appears when out of Home Service Area 6. Appears when call is in progress 7.
4 Safety Information For Wireless Handheld Phones Read this section before using your PCD2000A cellular telephone. Exposure To Radio Frequency Signals Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals.
5 Driving Check the laws and regulations on the use of wireless telephones in the areas where you drive. Always obey them. Also, if using your phone while driving, please: Give full attention to driving — driving safely is your first responsibility.
6 Posted Facilities Turn your phone OFF in any facility where posted notices so require. Aircraft FCC Regulations prohibit using your phone while in the air.
7 Important Information Warning! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
8 8. When using the battery charger, do not overload wall outlets and extension cords, as this can result in the risk of fire or electrical shock. 9. Never push objects of any kind into this product through ventilation slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
9 Welcome! You have chosen to enter the world of cellular telephone technology with one of the finest portable cellular phones available today, the PCD2000A .
Included in your Package If any of these items are missing or damaged, immediately contact your place of purchase. Read the Operating Guide thoroughly before operating the cellular phone. 10 PCD2000A Cellular Phone 600 mAh Nickel-Cadmium Battery PCD600Ni Standard Charger AD267 P C D 2 000A Operating Guide PCD2000A Operating Guide D:.
Features Plus these other features: 32 Numeric Digits Per Memory Location 10 Alpha Characters/Digits Per Memory Location Electronic Volume Controls Rechargeable Battery Pause Dialing Incoming Call Ind.
Fast Start Charging the Battery 1. Plug the charger into a wall outlet. 2. Plug the charger jack into the PCD2000A . 3. If you have the PCD1087 extended life battery, charge the battery for 6 hours. Otherwise, charge the cellular battery for 5 hours. Battery Alarm A Battery Warning Tone sounds when the battery charge is low.
Battery Memory Effect Rechargeable batteries can develop a “memory” (reduced charge capacity) caused by repeated charge and discharge cycles. Rechargeable batteries that have developed this effect will not operate to their fullest capacity.
Power Power ON Press and hold end for about one second. Digits, icons, and bars light briefly and then the Wake Up Tone sounds. ➪ The phone goes into the Idle Mode. Power OFF Press and hold end until you hear a beep — which is about one second. ➪ If a call is still in progress, power cannot be terminated until the call ends.
Calling To receive a call 1. Phone rings, CALL displays and the LCD flashes. ➪ 2. Press any key (except < / > ) and talk. 3. To hang up, press end . To make a call 1. Enter the phone number, 817 8583300 . ➪ 2. Press send . 3. If you hear no sound, the call did not go through.
Headset Menu For hands-free calling, you can add an optional headset. The headset menu has two settings: alert repeat or auto-answer. 1. To go to the phone settings menu from standby, press menu . 2. Press < once. 3. Press menu again. 4. Use the < or > keys to choose between AUTO ANSWER or ALERT REPEAT .
Mute Function The microphone can be muted while on a call. 1. To enable the mute function press menu then 0 . 2. To disable the mute function press menu and 0 again. Absent Call Counter When the PCD2000A is on, it registers the number of unanswered calls.
Memory - Store Numeric To Store in Specific Location 1. Enter the phone number, 817 8583300 . ➪ 2. Press M and hold about one second. 3. Enter the two-digit memory location number and press M . 4. To cancel, press end . OR 5. If a number is already stored in the specified location, the REPLACE prompt appears.
7. Enter the name and press M . 8. Press M and store the number. The screen returns to Normal after 2 seconds. OR To Store in Next Available Location 1. Enter the phone number, 817 8583300 . ➪ 2. Press M and hold for one second. 3. Press < / > to store in the next available number location.
To call a Number in Memory 1. Press M . ➪ 2. Enter the two-digit memory location number ( 00 - 50 ). 3. Press send . If a memory location of 51 or more is used, it is ignored. ➪ 4. To hang up, press end. MEMORY EMPTY displays on the LCD if no number is stored at the location entered.
Chain Dialing On certain occasions, after dialing a number, you may be requested by the party or service you are calling to enter a special access code, such as when performing a banking transaction. To store this number, refer to “Memory Store" on page 18.
Entering Characters This table shows the correspondence between the Numeric keys and the letters of the alphabet. Numeric Key Alphabet 11 2 A ,B ,C ,2 3 D ,E ,F ,3 4 G ,H ,I ,4 5 J ,K ,L ,5 6 M ,N ,O ,6 7 P ,Q ,R ,S ,7 8 T ,U ,V ,8 9 W ,X ,Y ,Z ,9 00 Example: To store the letter L, press 555 .
Example: To enter the name “JOE” in the display. 1. After storing a numeric number in a desired memory location, press and hold M for about one second. ➪ 2. Press 5 . 3. The cursor moves to the next position after 1 second. During letter entry, you can press # or * to move the cursor right or left respectively.
Dialing the Emergency One-Touch Number Note: The Emergency One-Touch Number is factory preset at 911 . To Dial the Emergency One-Touch Number 1. Make sure the power is on, and press and hold 9 for about 1 second. ➪ 2. Press end to hang up. Memory - Phone Number Review 1.
Memory - Search Alpha 1. Press M , M . ➪ 2. Enter part of the name. (See page 22 for letters.) 3. Press < to begin searching from the lowest number (00) or > to begin searching from the highest number (50) for the name entered. ➪ 4. To see next memory location with that name, press the same key ( < / > ) again.
PCD2000A Setup Use these menus to set up the features of the PCD2000A . Press N1 ➪ Chooses System Menu. Press N < / > ➪ System Select. < / > Press N2 ➪ Chooses Volume Menu. Press N < / > ➪ Earpiece Speaker Volume. < / > Press N3 ➪ Chooses Timer Menu.
Press N4 ➪ Chooses Password Menu. Press N ➪ Change Password. < / > Press N5 ➪ Chooses NAM Select. Press N < / > ➪ NAM #1 Select. < / > Press N6 ➪ Chooses PIN Menu. Press N< / > ➪ Enter PIN Number. < / > Press N7 ➪ Chooses Headset Menu.
Setting Systems for the PCD2000A If the “NSVC” indicator appears, you may be out of your service area, or your system may not be set correctly. (See page 35 for more information.) 1. Press N1 . ➪ 2. Press N again. Then, press < / > to see other options.
3. Select a volume and press M . ➪ 4. Press < for higher volume, or > for lower volume. 5. Press N to store the change. Or, to cancel and return to Standby, press end or clear . Setting Call Timers LAST CALL : Shows length of the last call made or answered (in minutes and seconds).
3. Press > . Display shows total length of all calls made or answered. ➪ 4. Press N to return to Standby. To reset the Total Call Timer, see the next section. Note: The Last Call Timer is reset each time you make or answer a call. To reset the Total Call Timer 1.
Setting the Password Set your own password to prevent unauthorized changes in your call timer. 1. Press N4 . ➪ 2. Press N . To cancel and return to Standby, press C . 3. Press N . ➪ 4. Type your password. (Factory preset is 0123 .) 5. Type your new password.
Selecting Number Assignment Modules (NAM) NAMs prevent unnecessary long distance or ROAM charges. Your service provider can register two NAMs in the PCD2000A . (See page for more information.) 1. Press N5 . ➪ 2. Press N . The current NAM is shown. 3.
3. Press N . ➪ 4. Press > . 5. Press N . To Enter Your Personal Identification Number (PIN) 1. Press N6 . ➪ 2. Press N . 3. Press > . ➪ 4. Press N .
5. Enter your password. Factory preset is 0123. ➪ 6. Enter the new PIN. For example, enter 1234 . 7. Press N . 34 D:...Pcd2000a new size.vp Fri Sep 25 14:58:07 1998 Color profile: Disabled Composite.
Advanced Functions When you travel, your PCD2000A has several advanced functions that can put your cellular in service, or eliminate unnecessary long distance or ROAM charges.
If you see NSVC on the display for more than a few seconds, the phone is an area that will not support operation in the selected Mode. You must then choose another. Modes A-ONLY and B-ONLY are used when you travel in areas other than your home area and the cellular coverage is strong wherever you go.
You may hear a recording (no airtime charge) that gives procedures for roaming calls and connects you immediately (during business hours) to a registration clerk.
Optional Accessories and Replacement Parts 38 Standard Charger AD267 Battery Eliminator/Charger PCD1004 600mAh NiCd Standard Battery PCD600Ni P C D 2 000A Operating Guide Operating Guide 850 mAh NiCd .
Specifications Channels: 832 Frequency Range: Transmit: 824.04 to 848.97 MHz Receive: 869.04 to 893.97 MHz Channel Spacing: 30 kHz Duplex spacing: 45 MHz Frequency Stability: +/- 2.5 ppm Receiver Sensitivity: -116 dBm at -4°F to +122°F 5.3 V +/-10% -113 dBm at -22°F to +140°F 5.
One Year Limited Warranty ONE YEAR LIMITED WARRANTY, BATTERY & ACCESSORIES 90 DAYS IMPORTANT: Evidence of original purchase is required for warranty service.
デバイスUniden PCD1080の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Uniden PCD1080をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUniden PCD1080の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Uniden PCD1080の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Uniden PCD1080で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Uniden PCD1080を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUniden PCD1080の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Uniden PCD1080に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUniden PCD1080デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
