United States StoveメーカーHOTBLAST 1950の使用説明書/サービス説明書
ページ先へ移動 of 20
INSTALLATION AND OPERATING INSTRUCTIONS FOR THE HOTBLAST 1950 EPA WOOD BURNING FURNACE Verified and tested following CSA B366.1 M91, UL 391-95, 99 by : Intertek Testing Services Distributed by: UNITED STATES STOVE COMPANY 227, INDUSTRIAL PARK ROAD P.O.
Please keep this document TABLE OF CONTENTS INTRODUCTION ...................................................................................................................... 2 1. CHIMNEY AND DRAFT ....................................................
INTRODUCTION Take note that this furnace operates like an EPA wood bu rning stove. This applies to the lighting, the embers and the minimum combustion air intake which depends on the type and the grade of the combustible. This model line is certified as meeting the emissi ons limits in 40 C.
W A R N I N G -THE ASH DRAWER AND EXCHANGERS ACCESS PA NEL GET VERY HOT. -DO NOT MANIPULATE WITH BARE HANDS. 2.2 ODOUR FROM THE PAINT It is normal that a smoke odour emanate from the unit when y ou first light it. It is recommended to burn it at high rate and ventilate the building until the odour resorbs.
2.5 SMOKE DETECTOR We highly recommend the use of a smoke det ector. It must be installed at least 15 feet (4,57 m) from the appliance in order to prev ent undue triggering of the detector wh en reloading.
3. APPLIANCE INSTALLATION 3.1 UNIT LOCATION The furnace must be installed where outsi de air supply is sufficient for prop er combustion. In airtig ht houses, it might be necessary to install an outside air inlet (see details in section 3.
3.3 PIPE CONNECTOR AND DAMPER Before proceeding to connection, remove all accessories such as scraper, shovel and poker from the evacuation pipe of the furnace. A 7” diameter chimney listed for use with wood burning hea ting appliances is highly recommended for the Hotblast 1950.
DAMPER The barometric control must be adjusted so that t he maximum draft measured at the furnace outlet is limited to - 0.06 in. w.c. Please note t hat a draft higher than -0.06 in. w.c. could result in an uncontrolla ble fire. On the other hand, the minimum draft to be respected is -0.
3.5 ELECTRICAL CONNECTION The following instructions do not supersede the local cod e. HOTBLAST 1950 On the Hotblast 1950 the combined limit control is installed with the support provided on the left side of the appliance (two holes are predrilled o n the edge of the furnace), and conne cted to the electrical box along with the transformer.
4. OPERATING INSTRUCTIONS Control system On the wood only furnaces , the thermostat controls the air inlet damper. When the thermostat calls for heat, the damper opens and th e fire burns up. When the furnace ge ts hot enough, the combined limit control activates the blower motor at the speed selected for woo d heating.
4.3 HEATING 1. When loading the furnace , spread the coal and em bers evenly in the center of the combu stion chamber before adding new logs. 2. Do not overload. Air must circulate freely in the upper part of the combustio n chamber in order to obtain an efficient operation of the appliance.
Whenever a high amount of smoke is noticed in the room, you mu st: 1. Open doors and windows. 2. Make sure the furna ce door is closed a s well as the dam per (if necessary, lower the thermo stat starting point or undo the chain of the damper and clo se t he barometric draft control manually).
5. MAINTENANCE 5.1 MAINTENANCE OF THE EXCHANGERS The evacuation pipe and the exchangers should be insp ected regularly durin g the bur ning season. Easy access is provided (without the use of tools): unscrew the wing nut on the exchangers access door.
5.2 CHIMNEY MAINTENANCE One of the most efficient methods is t o sweep the ch imney is using a hard brush. Brush the chimney downward so soot and creosote residues will com e off the inside su rface and fall at the bottom of the chi mney where it can be removed easily.
Door adjustment procedure: 1. Unscrew com plete ly the locking pin (see picture below). Lockin g p in 2. To increase t he pressure of the door on the gasket, turn the handle counter clo ckwise; to decrease the pressure on the door on the gasket, turn the handle clo ckwise.
7. WIRING DIAGRAM HOTBLAST 1950 WOOD DIRECT DRIVE RED ON 150°F LIMIT 250°F OFF 110°F LIMIT LOAD FAN LINE HONEYWE LL L6064 HIGH LINE LOW L2 120 V.A.C. L1 BLACK TRANSFO JUNCTION BOX 24 V.A.C. 24 V.A.C. THERMOSTAT SERVO-MOTOR RED BLACK WHITE BLACK BLACK 24 V.
8. HOTBLAST 1950 TECHNICAL DATA HOTBLAST 1950 A 47” B 25 ½” C 47 ¼” D 15 ⅞ ” E 28” F 24 ½” G 44” FLUE * 7” WEIGHT 560 * Reducer requi red 8.1 GENERAL TECHNICAL DATA MODEL DIRECT DRIVE OUTPUT TEMP VAR. BTU/ HR STATIC PRESSURE FILTER FAN MOTOR SPEED (CFM) ( O F) (WOOD) MIN.
9. DUCTS AND DAMPERS DIMENSIONS (EXAMPLES OF CALCULATION) SIMPLIFIED METHOD DISTRIBUTION SYSTEM Ducts size (heat) 4 inch outlet reduce by 1” 5 inch outlet reduce by 2” Always by 8” thick 6 inch outlet reduce by 3” N.B.: The main duct must be reduced every 2 outlets.
10. HOTBLAST 1950 BRICKS LAYOUT WARNING: INSTALL THE CERA MIC BLANKET PANEL BEFORE PUTTING BRICKS UP IN THE COMBUSTION CHAMBER 9" 4 1/2 " 3 1/ 2" 5 1/2" 9 4" 1 5/8 " 9&qu.
19 11. TROUBLE SHOOTING PROBLEM CAUSES SOLUTIONS Heating inefficient during the first combustions. Lack of draft. Improper adjustment of the barometric damper (ope ned too wide). Chimney flue restriction (too long., or too many 90 o elbows) Adjust the damper, minimize the chimney length and use 45 o elbows.
デバイスUnited States Stove HOTBLAST 1950の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
United States Stove HOTBLAST 1950をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUnited States Stove HOTBLAST 1950の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。United States Stove HOTBLAST 1950の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。United States Stove HOTBLAST 1950で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
United States Stove HOTBLAST 1950を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUnited States Stove HOTBLAST 1950の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、United States Stove HOTBLAST 1950に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUnited States Stove HOTBLAST 1950デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
