VDO CyclecomputingメーカーCytec C05+の使用説明書/サービス説明書
ページ先へ移動 of 20
BEDIENUNGSANLEITUNG INSTRUCTION MANUAL MANUEL D´INST ALLA TION ET D´UTILISA TION MANUALE D´INST ALLAZIONE E FUNZIONAMENTO INST ALACION Y OPERACIÓN MANUAL HANDLEIDING NÁVOD K MONTÁŽI A OBSLUZE I.
1 GB INST ALLA TION AND OPERA TION MANUAL - VDO CYTEC C05+ Preface Thank you for buying a VDO CYTEC bicycle computer . The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual.
GB 2 W arning: Before tightening the handlebar holder , make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible for you.
3 GB 1.2 Mounting the speed transmitter / sender The sensor should be mounted on the same side of the fork as the holder is on the handlebar . Make sure to position the respective rubber shim between fork and sender , position the curved back of the sender next to the spokes and make sure the sender is aimed at the receiver (computer head).
GB 4 1.3 Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly .
5 GB 1.4 Installing battery into computer head T o save battery power , your VDO CYTEC C05+ comes with the battery not yet fitted. Prior to initial use you have to install the battery first.
GB 6 1.5 Function Indicator Y our VDO CYTEC C05+ features a function indicator ((1)). When you are done mounting the computer , ((1)) flashes at the first rotation of the wheel. When the wheel-size is properly entered, actual speed is displayed as well.
7 GB UNLOCK LOCK 1.LOCK 2.CLICK 1.PRESS 2.UNLOCK.
GB 8 3. Information features of your VDO CYTEC C05+ Y our VDO CYTEC C05+ provides you with following information: KMH-MPH current speed indicated in either KMH or MPH, featuring automatic conversion into MPH DST trip counter , counts your trip distance up to 999,99 km or miles.
This button / key has several functions. All functions of the button / key are outlined in the chart below . Y our display Button / Key to Length of pushing What is going on? indicates following be pushed the button / key information DST -ODO-CLK-A TM push MODE key brief (0.
GB 10 5.1 Programming (setting up) your wheelsize In order for the VDO CYTEC C05+ to indicate your actual speed and your trip distance, the correct wheelsize has to be entered.
11 GB W atch out: In case you have selected MPH readout you must enter your wheelsize in mm. WS in mm 1x.
GB 12 5.3 Entering your wheelsize / entering odometer After initially installing the battery or after a battery change, your VDO CYTEC C05+ automatically switches into set-up mode for wheelsize and odometer .
13 GB In case you wish to enter the precise wheelsize you have measured yourself (i.e. 2257), please proceed with step 5. Step 5 : Not pressing the MODE button with in 2 seconds will make the last digit (212 4 ) flash and change the value (4-5-6-7...) Once the correct digit (7) comes up, press the mode button.
GB 14 Press immediatly 5 times to end Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Please wait 2 sec.
15 GB 5.4 Setting the clock CLK Y our VDO CYTEC C05+ features a clock with hour and minute display in 24 h mode T o access the clock set-up mode proceed as follows: Step 1: call in the CLK information into your display Step 2: Press the MODE button for 5 sec.
6. Resetting information to zero The following information may be reset to zero with your VDO CYTEC C05+: DST = trip distance A TM = trip counter W atch out: Both these information are simultaneously reset to zero T o reset either DST or A TM, one of these informations has to be displayed.
Hg 17 GB 8 . Battery change Tip: T ake down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. W atch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions.
GB 18 8 . Battery change Tip: T ake down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. W atch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions.
19 GB Contents 1 computer head 1 handlebar holder with screw 1 wireless transmitter with battery 12 V , type V23GA 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 V , type CR 2032 1 installation and operation manual TIP The CYTEC tin box easily holds a mini-tool and a spare tube to carry on with your ride.
デバイスVDO Cyclecomputing Cytec C05+の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
VDO Cyclecomputing Cytec C05+をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVDO Cyclecomputing Cytec C05+の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VDO Cyclecomputing Cytec C05+の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VDO Cyclecomputing Cytec C05+で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VDO Cyclecomputing Cytec C05+を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVDO Cyclecomputing Cytec C05+の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VDO Cyclecomputing Cytec C05+に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVDO Cyclecomputing Cytec C05+デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
