VenturerメーカーSHD7000の使用説明書/サービス説明書
ページ先へ移動 of 48
H D D V D p l a y e r M o d e l: S H D 7 0 0 0 R R TM Owner’ s Manual.
- 1 - SAFETY PRECA UTIONS On Placement • Do not use the unit in places that are extremely hot, cold, dusty, or humid. • Do not restrict the airflow of the unit by placing it in a place with poor airflow, by covering it with a cloth, or by placing it on carpeting.
- 2 - SAFETY PRECA UTIONS WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. FCC Information This device complies with Part 15 of the FCC rules.
- 3 - IMPOR T ANT SAFETY INSTR UCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings.
- 4 - PRECA UTIONS Notes on handling • Never disconnect the power cord from a wall outlet while the player is turned on, unless it is in an emergency. Doing so may cause malfunction. • When shipping the player, the original shipping carton and packing materials come in handy.
- 5 - TABLE OF CONTENTS Customizing the Function Settings ....... 22-34 Picture .................................................. 22-24 Audio ...................................................... 24-26 Language ......................................
- 6 - The unit can play: Region Management Information Region Management Information: This unit is designed and manufactured to respond to the Region Management Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, this unit cannot play that disc.
- 7 - FEA TURES Important notes about HD DVD HD DVD with high-definition content required for HD viewing. Viewing high-definition content and up- converting DVD content may require an HDCP capable DVI or HDMI input on your display device. Up- conversion of DVD content will result in near HD picture quality.
- 8 - Battery Replacement When the batteries become weak, the operating distance of the remote control is greatly reduced and you will need to replace them. CA UTION: Danger of e xplosion if batter y is incorrectly replaced. Replace only with the same or equivalent type.
- 9 - CONTROL REFERENCE GUIDE Remote Control 1) SUBTITLE Button Press to select one of the subtitle languages programmed on a D VD . 2) OPEN/CLOSE Button Press to open or close the disc tra y . 3) A UDIO Button Press to select one of the audio sound tracks programmed on a D VD or to select the audio output mode on an A UDIO CD .
- 10 - 14) ANGLE Button Press to switch the camera angle of the video presentation when scenes with multiple camera angles are recorded on a D VD . 15) I/ ST ANDBY/ON Button Press to turn on the unit and put it in standby mode. 16) DISPLA Y Button Press to change disc status information display ed on the TV screen.
- 11 - CONTROL REFERENCE GUIDE Unit (Front Vie w) Unit (Rear View) 11 ) AC IN Socket Connect the supplied power cord. 12 ) Ventilation Fan 13 ) LAN port Use this to connect to a network with an always-on broadband connection. 14 ) DIGITAL AUDIO OUTPUT BITSTREAM/ PCM OPTICAL Jack Outputs digital audio signals.
- 12 - DISPLA Y 4 6 1 5 7 2 3 8 9 10 11 12 13 14 15 16 17 1) Displays the video output format currently selected. (i: interlaced, p: progressive) 2) : Fast forward playback. : Fast reverse playback. 3) : Playing : Pausing 4) Shows a title number. 5) HD DVD: An HD DVD is loaded.
- 13 - SETUP Check the Type of Video Input on Your TV To view high definition content, use the HDMI OUTPUT jack or the COMPONENT VIDEO OUTPUT jacks to connect to a TV.
- 14 - SETUP • HDMI output is digital only . D VI analog is not suppor ted. • HDMI is an evolving technology , so some devices may not oper ate properly with this player . • T o get the most possible benefit from Dolb y Digital Plus, you should connect y our HD D VD play er to your A V receiver using its HDMI input.
- 15 - SETUP Note: This play er suppor ts sim ultaneous output of video on its HDMI and component video por t s. Howev er , some discs may restrict output of video on the component video ports when viewing high definition content or up-conv er ted D VD content.
- 16 - T urning on the Unit and TV 1. Press the ST ANDBY/ON button to turn on the unit. The ST ANDBY/ON indicator will tur n off . 2. T ur n on the TV by pressing its PO WER button. 3. Select the channel on your TV corresponding to the VIDEO IN jac k that the unit is connected to .
- 17 - PLA YING A DISC This owner’ s manual explains the basic instructions of this unit. Some DVDs are pr oduced in a manner that allows specific or limited operation during playback. Such as, the unit may not respond to all operating commands. This is not a defect in the unit.
- 18 - PLA YING A DISC Angle Selection Some D VDs contain scenes that hav e been shot from a number of diff erent angles. F or these discs, the same scene can be viewed from each of these different angles. 1. While you are pla ying a D VD with different angles recorded, press the ANGLE b utton to view the number of current angles available.
- 19 - PLA YING A DISC 1. Press the REPEA T button on the remote control. The repeat modes are listed. 2. Use the / buttons on the remote control to select the repeat mode. 3. Press the OK button on the remote control. Repeat playback starts. All Repeat: Repeats the entire disc.
- 20 - SPECIAL FUNCTIONS Display Function While the disc is playing, press the DISPLA Y button on the remote control to display inf or mation on operation status.
- 21 - SPECIAL FUNCTIONS A/B/C/D Buttons (on the remote control) Use these buttons as indicated by the video displa y during HD D VD playback . Depending on the disc contents, the functions of each b utton may diff er . Cursor Controls (on the remote control) Future HD D VDs ma y include game software and dra wing software.
- 22 - CUST OMIZING THE FUNCTION SETTINGS Notes: • When an HD D VD or a D VD has a particular picture shape, the contents may not be compatib le with other picture shapes. • D VDs containing 4:3 picture only always displa y 4:3 pictures regardless of the TV Shape setting.
- 23 - CUST OMIZING THE FUNCTION SETTINGS Picture Mode There are two types of source content in pictures recorded on D VDs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second).
- 24 - CUST OMIZING THE FUNCTION SETTINGS Audio Digital Out SPDIF T o select the output sound f ormat when connecting the DIGIT AL A UDIO OUTPUT jack. 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select Audio , then press the OK button.
- 25 - CUST OMIZING THE FUNCTION SETTINGS Downmixed PCM: Select this when a 2ch digital stereo A V receiver or processor is connected to this pla yer . When you pla y a D VD recorded in Dolby Digital, DTS, MPEG1 or MPEG2 f ormat, sound is converted into PCM (2ch) format to output.
- 26 - CUST OMIZING THE FUNCTION SETTINGS Dialog Enhancement T o tur n on or off a function that increases dialog volume of a D VD . 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select Audio , then press the OK button.
- 27 - Language Disc Menu Language T o select a pref erred language f or disc menus. 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select Language , then press the OK button. 3. Use the or button to select Disc Menu Language , then press the OK button.
- 28 - Ethernet P erf or m this setting if you connect the pla yer to your LAN. 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select Ethernet , then press the OK button.
- 29 - CUST OMIZING THE FUNCTION SETTINGS DHCP T o set y our network information. 1. Set “DHCP” to “On” and press the OK button. 2. Set “DNS” to “On” and press the OK button. The DNS ser v er is obtained automatically from the DHCP ser v er .
- 30 - CUST OMIZING THE FUNCTION SETTINGS MAC Address T o displa y the MAC address of the pla yer ( Fixed. No need to set.) Network Speed Select the speed and press the OK button. Cookie Setting Select “Accept” or “Not Accept” and press the OK button.
- 31 - CUST OMIZING THE FUNCTION SETTINGS General Parental Lock HD D VDs and D VDs equipped with a P arental Lock function includes predetermined limitation levels .
- 32 - CUST OMIZING THE FUNCTION SETTINGS Clock Set 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select General , then press the OK button. 3. Use the or button to select Clock Set , then press the OK button. 4.
- 33 - CUST OMIZING THE FUNCTION SETTINGS Screen Saver 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select General , then press the OK button. 3. Use the or b utton to select Screen Saver , then press the OK button.
- 34 - CUST OMIZING THE FUNCTION SETTINGS Maintenance 1. In STOP mode, press the SETUP button on the remote control. 2. Use the or button to select General , then press the OK button. 3. Use the or button to select Maintenance , then press the OK button.
- 35 - SYMPTOM CA USE (AND REMED Y) TROUBLESHOO TING GUIDE • The region number of the disc doesn't match the region number of this unit. No picture or abnormal color No power . • Ensure the AC power cord is connected. • The TV is not set to receiv e HD D VD/D VD signal output.
- 36 - LICENSE INFORMA TION ON THE SOFTW ARE USED IN THIS HD D VD PLA YER This document is statement purpose only . Not concerned with operation of this product. The software pre-installed in this HD D VD pla yer consists of m ultiple, independent software components.
- 37 - software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in eff ect making the progr am proprietar y . T o pre vent this, w e have made it clear that an y patent must be licensed for everyone's free use or not licensed at all.
- 38 - LICENSE INFORMA TION ON THE SOFTW ARE USED IN THIS HD D VD PLA YER exception, the source code distributed need not include anything that is normally distributed (in either source or binary form.
- 39 - OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABO VE, BE LIABLE TO Y OU FOR D AMAGES , INCLUDING ANY GENERAL, SPECIAL, INCIDENT AL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE.
- 40 - rights that we gave you. Y ou must make sure that they , too, receive or can get the source code. If you link other code with the library , you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it.
- 41 - Y ou may charge a f ee for the ph ysical act of transferring a copy , and y ou may at y our option off er warranty protection in exchange for a fee.
- 42 - Y ou must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are cov ered by this License .
- 43 - LICENSE INFORMA TION ON THE SOFTW ARE USED IN THIS HD D VD PLA YER contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
- 44 - LICENSE INFORMA TION ON THE SOFTW ARE USED IN THIS HD D VD PLA YER Exhibit C LICENSE ISSUES The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts.
- 45 - Exhibit D P or tions of this software are copyright © 2005 The F reeT ype Project (www .freetype.org). All rights reser ved. • This product includes software developed by the OpenSSL project.
- 46 - MAINTENANCE Cleaning the Unit • Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit. • Wipe the unit with a dry soft cloth. If the surfaces are e xtremely dir ty , wipe clean with a cloth that has been dipped in a weak soap-and-w ater solution and wr ung out thoroughly .
- 47 - Printed in China 811-HD7091W011.
デバイスVenturer SHD7000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Venturer SHD7000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVenturer SHD7000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Venturer SHD7000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Venturer SHD7000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Venturer SHD7000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVenturer SHD7000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Venturer SHD7000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVenturer SHD7000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。