VikingメーカーLPKPDRの使用説明書/サービス説明書
ページ先へ移動 of 10
F20525E EN (041414) Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 Installation Guide LPKPDR - Universal LP Conversion .
Table of Contents IMPORTANT– Please Read and Follow! 2 3 Fire/explosion hazard. IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. • DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
4 LP Orifice Conversion Kit Contents Excludes models VGR, VCM, VRT, VRT-R and D3 models. For information on these models, please contact customer service at 1-888-845-4641. 5 Regulator Conversion Flip Cap Hex Nut Cap Before proceeding with conversion, turn off gas supply and disconnect power to unit.
7 6 Infrared Broiler Conversion IMPORTANT: The infrared broiler orifice must be changed from rear of range before unit is installed. Locate bag labeled IR Broiler Orifice. Remove nut securing 90 degree fitting and broiler tubing to rear of range. Remove Orifice from 90 degree fitting and replace with orifice from bag labeled IR Broiler Orifice.
8 Locate bag labeled Sealed Burner Orifice Type 2. NOTE: If the burner is a PowerPlus™ Burner (check control panel), use orifice kit 011915-000 to convert this burner only. Remove the screws (Item #1) and set burner base aside (Item #2). IMPORTANT: Burner bases must be handled carefully to prevent igniter wires from becoming disconnected.
11 10 Orifice Locations (#61) (#63) (#61) (#67) (#57) (#65) (#65) (#57) (#67) DGRT301 DGRT361 (#60) (#67) (#58) (#70) DCCG130 DSCD130 Open Burner Type 3 Surface Burner Conversion Locate bag labeled Open Burner Orifice Type 3. Remove screws securing open surface burner to burner box and remove open surface burner.
13 12 Griddle Conversion (for models equipped with griddle) U-Shape Burner with Spark Ignition Locate bag labeled Griddle Orifice. Remove screws securing griddle venturi plate to griddle box and remove griddle venturi plate. Remove screws securing griddle burner to burner box.
15 14 Straight Tube Burner with Glow Bar Ignition Remove screws securing glow bar igniter to burner box and place glow bar igniter aside. Remove screws securing metal plate to burner box located underneath griddle burner and remove metal plate. Remove screws securing griddle burner to unit and remove griddle burner.
17 16 Wok Conversion (for models equipped with wok) Remove center trivet and/or grates, center ring and grate support. Lift and remove burner from unit. Loosen air shutter screw and adjust opening on burner to 5/8” and tighten air shutter screw. Remove orifice by turning counterclockwise and replace with orifice from bag labeled Wok Orifice.
19 18 Bake Conversion “U” Shaped Remove oven racks and rack supports. Remove oven bottom. Remove screws securing bake igniter to bake burner. Remove screws securing bake burner shield to oven burner box. Remove screws securing bake burner to oven burner box.
デバイスViking LPKPDRの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Viking LPKPDRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはViking LPKPDRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Viking LPKPDRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Viking LPKPDRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Viking LPKPDRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はViking LPKPDRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Viking LPKPDRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちViking LPKPDRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。