VinotempメーカーWINE-MATE WM1500 HTD-TEの使用説明書/サービス説明書
ページ先へ移動 of 23
WINE-MATE Cooling Unit Use & Care Manual WM1500 HTD, HTD-TE WM2500 HTD, HTD-TE V V i i n n o o t t e e m m p p I I n n t t e e r r n n a a t t i i o o n n a a l l C C o o r r p p . . w w w w w w . . v v i i n n o o t t e e m m p p . . c c o o m m w w w w w w .
- 1 - Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAUL T INTERRUPTER (GFI). • A DEDICATED 20 AMP CIRCUIT IS REQUIRED.
- 2 - TABLE OF CONTENTS Features & Specifications.…………………….……………..3 Installation Instruction……………………………………….
- 3 - Features and Specifications • WM1500HTD, HTD-TE and WM2500HTD, HTD-TE cooling units are designed and used to provide a subtle temperature between 50~65 °F for suitable space at a normal environment. • The refrigerated space will mainta in humidity of 50~70% RH even when the environment becomes dry and humid.
- 4 - Fig. 1.2 DIMENSIONS (in) The dimensions and capacity are specified as follows: Model Exhaust CFM Capacity cu ft (55°F/75°F) Electrical Weight (lb) 1500htd Rear Exhaust 120 90 115V/60Hz/4A 55 1.
- 5 - Installation Instruction NOTES: 1) DO NOT INSTALL ANY DUCTS ONTO THE SUPPLY, INTAKE AND EXHAUST. 2) MOUNTING BRACKETS, SCREWS, GASKETS AND OTHER SEAL MATERIALS ARE NOT INCLUDED. 1. Cabinet Location • Place the wine cabinet in a properly ventilated location.
- 6 - • If top exhaust, cut another rectangular ope ning at the top of the cabinet to the length and width of the t op exhaust (see Fig.2.2 & 2.3). • Make 2 holes at the ceiling and insta ll the ¼” inside di ameter wood thread inserts (see Fig.
- 7 - Fig. 2.2 TOP EXHAUST CUTOUT Fig. 2.3 CUTOUT A ND HOLE DIMENSIONS.
- 8 - Fig. 2.4 GASKET AND SCREW INSERT Fig. 2.5 COOLING UNIT MOUNTING (EXPLODED).
- 9 - Fig. 2.6 COOLING UNIT MOUNTING (COMPLETED) Fig. 2.7 COOLING UNIT MOUNTING (REAR EXHAUST) Fig. 2.8 COOLING UNIT MOUNTING (TOP EXHAUST).
- 10 - Fig. 2.9 TOP EXHAUST GASKET 3. Electrical Cord • Because of potential safety hazards under a certain condition, we strongly recommend against the use of an extens ion cord.
- 11 - Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 ° F for the optimum aging of wine • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantit y of bottles, temperature setting and surrounding temperature.
- 12 - 2.1 LED Functions LED MODE FUNCTION ON Compressor enabled Flashing Anti-short cycle enabled ON Defrost cycle enabled ON Fan enabled Flashing Fan delay after defrost enabled ON Alarm occurring ON Temperature measuring unit Flashing Programming mode 3) Alarm Signals 3.
- 13 - 1. Press the SET + keys for 3 sec until the “ °C” or “°F” LED starts blinking, then release the keys. 2. Press again the SET + keys for more th an 7sec until the Pr2 label will be displayed, then release the keys. The first parameter Hy will be displayed.
- 14 - Care Guide I. Component Identification Fig. 4.1 Exploded View.
- 15 - II. Condenser Coil Cleaning • The condenser coil is on the ambient air intake side of the cooling unit. • Clean the condenser coil regularly .
- 16 - Troubleshooting This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration servic e person, not is it comprehensive Complaint Possible Causes Response 1. Unit not running a. Power co rd u nplugged b.
- 17 - l. Failed components l. Chec k compressor wi ndings, start relay and overload protector 5. Unit running too long a. Improper room insulation & seal b. Exhaust restricted c. Room too large d. Ambient temperature higher > 90 ° F e. Dir ty C ondenser f.
- 18 - rising high 11. Evaporator freezing up a. Evaporator air flow restricti on b. Not stopping due to air leak, high ambient temperature or low setting c. Low ambient temperature d. Bad thermostat or sensor e. Moisture in the system f. Refrigerant low or leaki ng g.
- 19 - Wiring Diagram Fig. 6.1 WIRING DIAGRAM.
- 20 - Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.
- 21 - Warranty Thank you for choosing a Vinotemp cooling unit. Please enter the complete model and se rial numbers in the space provided: Model_____________ _________________________ __ _________________ Serial No._________________ ____________________ _________________ Attach your purchase receipt to this owner’s manual.
- 22 - is determined to be faulty and is within the twelve month warranty period VINOTEMP will, at its discret ion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect.
デバイスVinotemp WINE-MATE WM1500 HTD-TEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Vinotemp WINE-MATE WM1500 HTD-TEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVinotemp WINE-MATE WM1500 HTD-TEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vinotemp WINE-MATE WM1500 HTD-TEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vinotemp WINE-MATE WM1500 HTD-TEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vinotemp WINE-MATE WM1500 HTD-TEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVinotemp WINE-MATE WM1500 HTD-TEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vinotemp WINE-MATE WM1500 HTD-TEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVinotemp WINE-MATE WM1500 HTD-TEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
