VTechメーカーVT 1900の使用説明書/サービス説明書
ページ先へ移動 of 17
@za VTECH COMMUNICATIONS LTD. Is a trademark of VTECH COMMUNICATIONS LTD.., a member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTECH Communications, 8770 SW Nimbus Avenue / Beaverton, Oregon, 97008. Distributed in Canada by VTECH Electronics Canada Ltd.
Page INTRODUCTION ............................................................................................................. 1 SPECIAL FEATURES ...................................................................................................... 2 PARTS CHECK LIST .
Congratulations! You have purchased one of the most sophisticated cordless telephones on the market! The VTech VT1900 has been designed to offer a new standard in cordless telephone technology.
Parts Check List To purchase replacement battery 1. Base unit, Handset and AC adapter packs, call VTECH Communications at 2. One-Line Telephone Cord 1-800-624-5688. In Canada, call HANDSET UNlT CONTROLS AND FUNCTIONS 3. Battery Pack VTECH Electronics at 1-800-267- 4.
This equipment complies with Parts 15 BASE UNIT CONTROLS AND FUNCTIONS and 68ofthe ~ederal Communications Commission (FCC) rules for the United - TONEIPULSE AC POWER JACK PHONE CORD JACK ANTENNA BAlTE.
FCC Part 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJIIC, RJIlW or RJ14). Your telephone company may discontinue your service if your equipment causes harm to the telephone network.
When using your telephone equipment, basic safety precautions shouldalways be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product.
Follow the steps below: 1. Remove the battery case cover by pressing on the ridged lines and slidina downward. PRESS and SLIDE DOWNWARD 2. Discard the old battery pack. Don't put the old battery pack in a trash compactor or a fire - it could burst.
Fill in the telephone number card on the base unit. CARD CHEAK FOR A DIAL TONE. After the batteries are charged, pick up the handset. Now press PHONE on the handset, you should hear dial tone. If not, see 'IN CASE OF DIFFICULTY' on page 26. CAUTION: 1.
USING THE WALL MOUNT ADAPTOR 1. Position the wall mount bracket on the base. Line up the tabs on the wall mount adaptor with the holes on the bottom of the base (Figure 1). Snap the wall mount bracket firmly in place. 2. Mount the base on the wall. Position the base so the mounting studs will fit into the holes on the bottom of the base.
MEMORY STORING The phone should be m. press (PTG) . Enter the two digit memory location (00 .. 20). Enter the number you wish to store, up to a maximum of 20 digits. Press (MEM) to store number and exit program mode. MEMORY STORING -11 1 MEMORY DIALING Enter the memory location of the number you wish to dial (00.
TEMPORARY TONE If you have a rotary (dial-pulse) telephone service, (TONEIPULSE switch is set to PULSE), this feature allows you to enter special codes and tones to operate answering machines, use electronic banking services, calling cards, or other special services.
The VTech VT1900 is capable of memory dialing. You can dial by pressing the memory location in which the number was stored. STORING SPEED DlAL NUMBERS To program a speed dial location, do the following: With the hone @@ mode. Press (&G) . The PHONE LED will flash quickly to indicate that the unit is in program mode.
CHANGING STORED NUMBERS To change or replace a stored number, simply store a new number in the desired memory location following the instructions listed in, STORING SPEED DIAL NUMBERS. See page 21. DELETING STORED NUMBERS To delete a stored number from memory do the following: Press to enter program mode.
If the handset is moved to a point where the base and handset can no longer communicate, the handset will make a quick series of beeps to signal Out of Range. OUT OF RANGE WHEN PHONE IS ON ' If you are presently engaged in a phone conversation move closer to the base.
YOU HEAR OTHER CALLS WHILE USING YOUR PHONE. Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company.
FREQUENCY CONTROL Crystal Controlled Dual PLL Synthesizer TRANSMIT FREQUENCY Handset: 925.05 MHz to 927.75 MHz (All ten channels within this range) Base: 902.3 MHz to 905.0 MHz (All ten channels within this range) RECE~VE FREQUENCY Handset: 902.3 MHz to 905.
デバイスVTech VT 1900の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
VTech VT 1900をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVTech VT 1900の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VTech VT 1900の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VTech VT 1900で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VTech VT 1900を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVTech VT 1900の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VTech VT 1900に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVTech VT 1900デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。