VTechメーカーVT 1980の使用説明書/サービス説明書
ページ先へ移動 of 20
900 MHz 1 ! DlGlTA L SPREAD SPECTRUM CORDLESS HONE MODEL VT 1'980/ VT.1981 VTECH COMMUNICATIONS LTD. Distributed in the U.S.A. by VTECH Communications,8770 SW Nimbus Avenue/ Beaverton, Oregon, 97008 distributed in Canada by VTECH Electronics Canada Ltd.
Table of Contents I INTRODUCTION ................................................................ 1 I Parts Check List: ................................................................................... 2 IMPORTANT SAFETY INSTRUCTIONS ...............
OPERATING INSTRUCTIONS ........................................ 14 ! MAKING CALLS .................................................................................. 14 I I ANSWERING CALLS ...............................................................
Parts Check List: ! I When using your telephone Handset Base unit Battery pack Belt Clip n Handset Charging CradleISpare Battery Charger Telephone line cord AC adaptor Wall mounting adaptor Y Screws a.
voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. 11 .Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
To charge the batteries, place the handset in the base unit. The CHARGE indicator will light to show the handset is seated properly and the batteries are charging.
6. CHECK FOR A DIAL TONE. After the batteries are charged, rotate the base unit antenna to an upright position.Next, pick up the handset and press the ONIOFF key. The PHONE LED should light up, and you should hear a dial tone. If not, see IN CASE OF DIFFICULTIES.
4. POSITION THE WALL MOUNT ADAPTOR ON THE BASE. lnsert the AC power adaptor cord and the telephone line cord in the wall brackedt notches. Line up the tabs on the wall mount adapter with the holes on the bottom of the base. Snap the wall mount adaptor firmly in place.
PHONE LED The PHONE LED lights when the phone line is being used by the handset. It flashes during the programming mode. It flashes quickly when the line is on hold. BATT LOW LED The BATT LOW LED will flash quickly when the handset battery is getting low and needs to be recharged.
MAKING CALLS Pick up the handset and press ONIOFF. When you hear a dial tone, dial the number. The PHONE LED on the handset and IN USE LED on the base unit will light. If you make a mistake when dialing, press ONIOFF again to hang up, then press ONIOFF to get the dial tone again.
To select a different ringer type do the following: 1. Press FLASH 2. Press a key 1 ..4 to select a ringer type A confirmation ring will be heard for the new ringer type.
STORING PAUSES IN MEMORY USING REDIAL To insert a pause in a phone number, press RDLIP at the appropriate point when storing the number. This inserts a 2 second pause. For longer pauses, press RDUP two or more times. Each press makes the pause 2 seconds longer and is treated as a stored digit.
THE MUTE FEATURE When you press MUTE while using your phone, you can hear the caller's voice, but they cannot hear you. You can use this feature to speak to someone in the room without the caller listening. While a call is muted the BATT LOW LED on the handset will be on.
Your VT 1980 / VT 1981 cordless telephone is equipped with a 2.5mm Headset Jack for use with an optional accessory Headset for hands-free operation. If you choose to use the Headset option, you must do the following: The VT 1980 / VT 1981 is also equiped with a detachable belt clip.
TAKING CARE OF YOUR TELEPHONE Your VT 1980 I VT 1981 cordless telephone contains sophisticated electronic parts so it must be treated with care. AVOID ROUGH TREATMENT Place the handset down gently. Save the original packing material to protect your telephone if you ever need to ship it.
Problem Remedy YOU GET NOISE, You may be out of range. Either move STATIC, OR A WEAK closer to the base, or relocate the base SIGNAL WHEN YOU'RE unit. AWAY lHE BASE The layout of your home may be limiting UNIT the range. Try moving the base unit to the second or third floor, or to some other location.
WHAT DOES OUR WARRANTY COVER ? WHAT DOES OUR WARRANTY NOT COVER ? Any defect in material or workmanship. -A;.. FOR HOW LONG AFTER THE ORIGINAL PURCHASE ? To the original purchaser only-ONE YEAR. WHAT WILL VTECH DO ? At our option, repair or replace your unit.
This equipment complies with Part 15 and 68 of the Federal Communications Commission (FCC) rules for the United States.lt also complies with rules RSS-210 and CS-03 of Industry Canada (IC) for Canada.
IC (Industry Canada) This telephone is registered for use in Canada. Notice:The REN assigned to this device denotes the number of devices you may connect to the telephone loop which is used by the device to prevent overloading.
VTECH VT 1980 / VT 1981 Cordless Telephone Wall Mounting Template Use this template when wall mounting your base unit .To mark the positions of the mounting screws, hold this template against the wall, and press a pencil or pen point through the center of each crossmark.
デバイスVTech VT 1980の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
VTech VT 1980をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVTech VT 1980の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VTech VT 1980の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VTech VT 1980で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VTech VT 1980を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVTech VT 1980の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VTech VT 1980に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVTech VT 1980デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。