VTechメーカーVT 2960の使用説明書/サービス説明書
ページ先へ移動 of 48
1 INTRODUCTION Thank you f or purchasing a VT ech cord- less telephone. This manual is designed to f amiliarize you with y our VT 2960. To get the maximum use from your new phone, we suggest that you read this In- struction Manual before using your VT 2960 .
2 INTR ODUCTION SPECIAL FEA TURES • 900MHz Operation • Fully Digital Link between Handset and Base Unit with ADPCM voice coding for enhanced audio quality • Digitally-Scramb led V oice Commu- ni.
3 Parts Check List 1. Base Unit, Handset and AC Adaptor 2. Longer T wo-Line T elephone Cords 3. Shor ter T elephone Cord(f or mounting) 4. Batter y P ack 5. W all mount bracket 6. Belf-clip T o purchase additional Batter y P acks, call VTECH Communications at 1-800-595-9511.
4 IMPOR T ANT SAFETY INSTRUCTIONS VII.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company . VIII.Do not allow anything to rest on the power cord.
5 E. If the product has been dropped and the cabinet has been damaged. F . If the product exhibits a distinct change in performance. XIII.A void using a telephone (other than a cordless type) during an electrical stor m. There ma y be a remote risk of electric shock from lighting.
6 RECHARGEABLE B A TTER Y P A CKS Charging the Handset batteries The Handset of your VT ec h 2960 cord- less telephone is powered by a re- chargeable battery pack. It charges automatically whenever the Handset is in the Base Unit cradle. Y ou should charge the battery pack for 16 hours when you first receiv e y our phone .
7 PLEASE NOTE THE CORRECT POSITION OF THE BA TTERY P ACK WHEN CHANGING BA TTERY PLACE THE NEW BA TTERY P ACK INTO THE BA TTERY COMP ARTMENT PRESS and SLIDE DOWNW ARD CHARGE THE HANDSET BA TTERY P ACK FOR 16 HOURS BEFORE USING 14 15 16 17 18 19 20 ERASE Replacing The Handset Battery Pack 1 .
8 TONE PULSE REPEAT ANSWER MSG STOP/PLAY SKIP ANSWER MSG MSG SELECT ON/OFF RECORD/ MEMO VOLUME INT.COM HOLD MUTE CONF. LINE 1 LINE 2 OFF MSG L1 L2 POWER CHARGING SPARE BATTER Y ERASE SELECT TIME/SET 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 Figure 1 Figure 2 The W all Mount bracket is designed to fit on standard W all Mount plates.
9 HANDSET FEA TURES 1 LINE 2 LINE 1 OFF LINE 2 CID REDIAL PROG MEM CONF INT .COM 1 2 3 4 5 6 7 0 * abc def ghi jkl pqrs tuv wxyz tone oper FLASH FLASH HOLD P AUSE DELETE CLEAR 8 9 mno ANTENNA DISPLA Y BEL T CLIP NOTCH VOLUME UP KEY VOLUME DOWN KEY LINE (FLASH) KEYS OFF KEY DIALING KEYS ( 0-9) 7.
10 LINE 1 KEY Press this key to select LINE 1. If the Handset has already accessed LINE 1, pressing this key will FLASH the line. If LINE 1 is on HOLD, pressing this key will take LINE 1 off HOLD and return you to your call. If LINE 2 is IN USE, or you are in CONFERENCE mode, pressing this key access LINE 1 and put LINE 2 on HOLD.
11 REDIAL KEY Press this key to display and/or dial the last number you called. When the Handset is On (with dial tone), press this key to dial the last number called. When the Handset is Off , pressing this key will display the last dialed phone number on the LCD .
12 The VT 2960 is also equipped with a detachable belt clip . Align the pins on the inside edge of the belt clip with the notches on the inside of the VT 2960 Handset.
The handset has accessed LINE 1 The handset has accessed LINE 2 The Base Unit has accessed LINE 1 The handset has accessed LINE 1, while the Base Unit has accessed LINE 2 Both handset and Base have ac.
14 Handset is asking for 2-digit location during Memory Dial programming A mistake was made during Memory Dial programming Enter a 2-digit location for Memory (Speed) Dialing The contents of a Memory .
15 EXAMPLES OF THE LCD DISPLA Y The contents of Memory Dial location #13 Y ou ha ve deleted Memory Dial location #15 T o prev ent accidental deletions of all CID records or Memory Dial locations, this.
16 B ASE UNIT FEA TURES BASE UNIT FEA TURES REPEAT ANSWER MSG STOP/PLAY SKIP ANSWER MSG MSG SELECT ON/OFF RECORD/ MEMO VOLUME INT.COM HOLD MUTE CONF. LINE 1 LINE 2 OFF MSG L1 L2 VT 2960ci POWER CHARGING SPARE BA TTERY ERASE MENU SELECT TIME/SET MEMORY DIALING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 TONE PULSE 9V DC TEL.
17 LINE 2 (EXTENSION IN USE) LED Glows steadily when the Base Unit is accessing LINE 2. Flashes slowly when only the Handset or an extension phone is accessing LINE 2. Flashes rapidly when LINE 2 is placed on HOLD. Flashes in cadence with the incoming ring when you receive a call.
18 B ASE UNIT FEA TURES CONF KEY Press this key to conference LINE 1 and LINE 2. HOLD KEY Press this key to place your call on HOLD. Press the appropriate LINE key to can- cel HOLD. In CONFERENCE mode, press this key to place both lines on HOLD. Press CONF to cancel HOLD.
19 Setting up y our VT ech VT 2960 1. Choose an area near an electrical outlet and telephone wall jack(s). 2. Plug the AC po w er adaptor into the electrical outlet and the DC connector to the back of the Base Unit. CA UTION: Use only the AC adaptor shipped with your VT 2960.
20 MAKING CALLS Extend the Antenna whenever y ou remove the Handset fr om the Base Unit cradle There are two ways to make a call: • Press LINE 1/FLASH or LINE 2/ FLASH and listen for dial tone . The LCD will display HANDSET ON 1 (or 2 ) . Dial the phone number .
21 ANSWERING CALLS FROM THE BASE UNIT (SPEAKERPHONE) In addition to the audible ringer , the LINE LED flashes in cadence with the incoming ring signal to indicate an incoming call. With the Base Unit OFF: When the phone rings, press the appropriate LINE key .
22 NOTE: If you use the Speakerphone in an environment that is not very quiet, your caller’ s voice ma y f ade in and out. Should this occur , press the MUTE key before your party begins to speak, then press MUTE again (to turn MUTE off) when it’ s y our turn to speak.
23 Base Unit Paging Handset When the INT .COM k ey is pressed on the Base Unit, the Handset will ring dif- f erently than its incoming call ring. The LCD will displa y BASE P AGING HAND- SET , as well. The Handset user can then do the following: • Press INT .
24 CONFERENCE CALLS This feature allows you to link both lines together for a 3-way conversation between you and the parties on LINE 1 and LINE 2. Conference calls can take place from the Handset or the Base Unit.
25 Programming the Base Unit Ringer 1. Press and hold the MEM/PROG key until the LCD displays PROGRAM LOCA TION _ _. 2. Press #. LCD displays ?: 1=HANDSET 2=BASE. 3. Press 2 . LCD displays ?: 1=LINE 1 2=LINE 2. 4. Press 1 (or 2 , depending on which line you’re programming).
26 DELETING ST ORED NUMBERS Y ou can delete individual phone num- bers stored in memor y , or all stored numbers at one time. T o Delete a single phone number stored in Memory: With the Handset OFF , .
27 Y our VT 2960 cordless telephone is ca- pab le of displaying the name and phone number of the calling party , before y ou ans wer the call. In addition, it will dis- pla y Caller ID inf or mation when you are on the phone and receiv e a Call Wait- ing signal.
28 3. Press INT .COM/DELETE to confirm deletion of all CID records. The LCD will displa y DELETING ALL CALLS . Pressing any key other than INT .COM/DELETE cancel this op- eration. DIALING FROM CID MEMOR Y NOTE: Only the last 7 digits of the phone number will be dialed from CID memor y .
29 ST ORING CID RECORDS IN MEMOR Y DIALING LOCA TIONS Y ou can store a phone number from a CID record in a Memory Dialing loca- tion. 1, With the Handset OFF , press the CID key . 2. Use the * ( ) or # ( ) keys to scroll to the CID record you wish to store in memor y .
30 THE VT2960 ANSWERING SYSTEM the Base Unit. The Base display becomes a timer as you record your message. 5 . Press ST OP/PLA Y when you complete your outgoing message. It will automatically be played back to you. Y ou can re-record y our outgoing message at any time, by repeating the above sequence.
31 diff erent secur ity code f or each line. T o set the security code: 1. Press MENU . V oice prompt sa ys, " Please select line ." 2 . Press SELECT until the voice prompt announces the desired line. 3. Press TIME/SET . The voice prompt will confirm your line choice, followed by " Set outgoing message .
32 THE VT2960 ANSWERING SYSTEM The f ollowing programming aff ects both lines, simultaneously: • Call Screening • Audib le Message Aler t • Day and Time CALL SCREENING This feature allows you to hear incoming messages at the Base Unit, while they are being recorded.
33 THE VT2960 ANSWERING SYSTEM SELECT button down will increase the minute setting by increments of 10. 7. Press TIME/SET . V oice prompt will announce the current day and time.
34 THE VT2960 ANSWERING SYSTEM SELECTING LINES FOR MESSAGE PLA YB ACK Pressing the MSG SELECT button allows you to hear recorded messages from Line 1 , Line 2 , or Both Lines . As you press MSG SELECT , the corresponding L1 MSG and L2 MSG indicators will illuminate.
35 ANSWER MSG STOP/PLAY SKIP ANSWER MSG MSG SELECT ON/OFF RECORD/ MEMO VOLUME HOLD MUTE CONF. LINE 2 OFF MSG L1 L2 VT 2960 MENU SELECT TIME/SET ANSWER MSG STOP/PLAY SKIP ANSWER MSG MSG SELECT ON/OFF RECORD/ MEMO VOLUME HOLD MUTE CONF.
36 ON LEFT EAR ON RIGHT EAR ONE INCH Y our VT2960 cordless telephone is equipped with a 2.5mm Headset Jack for use with an optional accessory Headset or hands-free operation. If you choose to use the Headset op- tion, you must do the following: INST ALLA TION Obtain an optional accessory Headset, which is compatible with the VT2960 .
37 MAINTENANCE MAINTENANCE T AKING CARE OF YOUR TELEPHONE. Y our VT ech VT 2960 cordless telephone contains sophisticated electronic par ts so it must be treated with care . A void r ough treatment Place the Handset down gently . Sav e the original packing materials to protect your telephone if you ever need to ship it.
38 Y OU GET NOISE, ST A TIC, OR A WEAK SIGNAL EVEN WHEN Y OU’RE NEAR THE B ASE UNIT . • Place the Handset in the Base mo- mentarily to reset the security code. Then press LINE to get a line. Household appliances plugged into the same circuit as the Base Unit can some- times cause interf erence.
39 IN CASE OF DIFFICUL TY COMMON CURE FOR ELECTRONIC EQUIPMENT Electronics, like people, can sometimes get confused. If the unit does not seem to be responding normally , then tr y putting the Handset in the cradle to re-initialize the unit. If it still does not seem to respond, perform the following steps (in the order listed): 1.
40 W ARRANTY ST A TEMENT WHA T DOES OUR W ARRANTY CO VER? • Any defect in material or workmanship. FOR HO W LONG AFTER THE ORIGINAL PURCHASE? • T o the or iginal purchaser only - ONE YEAR. WHA T WILL VTECH DO? • At our option, repair or replace your unit.
41 WHA T DOES OUR W ARRANTY NO T CO VER? • Batteries • Damage from misuse, neglect, or acts of nature (lightning, floods, power surges, etc.) • Products which may have been modified or incorporated into other products • Products purchased and/or operated outside the USA, its territories, or Canada.
42 This equipment complies with Parts 15 and 68 of the Federal Communications Commission (FCC) rules for the United States. It also complies with Industry Canada (IC) rules RSS210 and CS-03 for Canada. A label is located on the underside of the Base Unit containing either the FCC reg- istration number and Ringer Equivalence Number (REN).
43 FCC P ar t 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJ11C/RJ11W or RJ14C/RJ14W). Y our telephone company ma y discontinue your service if your equipment causes harm to the telephone network.
44 IC (Industry Canada) This telephone is registered for use in Canada. Notice: The REN/IES assigned to this telephone determines the number of devices you may connect to the telephone loop which is used by the device to prev ent ov erloading.
45 WEIGHT Handset : 292 g (Battery included) Base : 800 g POWER REQUIREMENTS Handset : Self-contained nickel-cadmium rechargeable battery supply , 3.6V nomi- nal, 600mAh capacity . Base : 11V DC 600mA MEMOR Y Speed Dial: 20 Memory locations,20 digits per location.
46 T ABLE OF CONTENTS INTRODUCTION ......................................................................................................... 1 Special Features ...........................................................................................
47 T ABLE OF CONTENTS SWITCHING FROM THE HANDSET T O BASE OR BASE T O HANDSET .................... 22 Switching from Handset to Base Unit Speakerphone ................................................. 22 Switching from Speakerphone to Handset ........
Is a trademark of VTECH COMMUNICATIONS LTD.., a member of THE VTECH GROUP OF COMPANIES. VTECH COMMUNICATIONS LTD. Distributed in the U.S.A. by VTECH Communications, 8770 SW Nimbus Avenue / Beaverton, Oregon, 97008. Distributed in Canada by VTECH Electronics Canada Ltd.
デバイスVTech VT 2960の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
VTech VT 2960をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVTech VT 2960の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VTech VT 2960の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VTech VT 2960で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VTech VT 2960を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVTech VT 2960の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VTech VT 2960に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVTech VT 2960デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
