Wasp Bar CodeメーカーWPL305の使用説明書/サービス説明書
ページ先へ移動 of 17
WPL305 Thermal Label Printer User’s Guide For Wasp Technologies DT/TT Printer Copyright Wasp Bar Code Technologies 2004. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means without the written permission of Wasp Bar Code Technologies.
1. Introduction ............................................................................................1 2. Getting Started .......................................................................................1 2.1 Unpacking and Inspection ....
1. Introduction Thank you for purchasing the W305 Thermal Transfer and Direct Thermal Bar Code Printer. Although the printer takes only a small amount of space, it delivers reliable, superior performance. This printer provides both thermal transfer and direct thermal printing at user selectable speed of: 2.
2.3 Printer Parts Figure 1: Top front view 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off.
ribbon, please refer to the ribbon calibration procedure to calibrate the ribbon sensor. NOTE: If you are using direct thermal labels you should not load a ribbon.
Make sure both the ribbon access window and the printer top cover are closed when powering up the printer. 3.3 Loading Label Stock 1. Insert a 1” label spindle into the label roll. If your paper core is 1 inch, you can remove the 1.5” core adapters from the centering tab.
Figure 6: Label installation 4. Feed the paper, printing side face up, under the Teflon bar and the paper guide and pass over the platen. 5. Adjust the yellow center-biased paper guides to slightly touch the edges of the label backing.
Figure 7: Top cover support is fixed at position 2 4. To close the cover, lift up the top cover to the ultimate angle then close the top cover gently and it will be kept at a stop position between 1 and 2 for a while. The cover will close automatically after several minutes.
Figure 9: Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is locked at a stop position, please do not push top cover to close it or the top cover will be damaged. Instead, open the top cover as wide as it will go and close the cover again.
4. Power on Utilities There are three power-on utilities to set up and test printer hardware. 1. Printer initialization 2. Ribbon sensor calibration 3. Gap or black mark sensor calibration Note: You must run the #2 and #3 utilities after running the #1 to properly set up the printer.
4.3 Gap/Black Mark Calibration Gap/black mark sensor sensitivity should be calibrated at the following conditions: 1. A brand new printer 2. Change label stock 3. Printer initialization Please follow the steps below to calibrate the sensor. 1. Turn the printer power off.
The printer will enter dump mode after printing the printer configuration. In dump mode, all characters will be printed in 2 columns as in the figure below. Figure 11: Dump mode printout The left side characters are received from your system and the right side data are the corresponding hexadecimal values of the characters.
5. Maintenance 5.1 Cleaning Use one or more of the following supplies that meets your needs: n Cleaning pens n Cleaning swabs n Lint-free cloth Printer Part Method Printer Head n Let the print head to cool for one minute. n Use a cleaning pen to swab the print elements.
Utilities . 6.2 Print Quality Continuous feeding labels n The printer settings may be wrong. Please do the Initialization and Gap/Black Mark Calibration . No print on the label n Is the label or ribbon loaded correctly? Follow the instructions in Loading the Labels or Loading the Ribbon .
7. Specifications 7.1 Printer Specifications Item W305 Mechanism Resolution 203 dpi. Max. Print Width 108 mm. Max. Print Length 1000 mm ( 39” ). Ribbon Capacity 300 meter with 1” core. (Max. OD 67 mm) Printing Speed 2, 3, 4 and 5 ips. Peeler function 2, 3 ips Printing Method Direct thermal and thermal transfer printing.
Wound Type Outside wound. Width 20mm ~ 112mm (0.78” ~ 4.4”). Length 10mm ~ 1000mm (0.4” ~ 39”). 25.4mm ~ 1000mm (1” ~ 39”).(for peeler and cutter) Thickness 0.06mm ~ 0.19mm. (2.3~7.4 mil), max. 150g/m 2 Roll Diameter 5”. Roll Core Diameter 25.
This warranty is limited to repair or replacement at Wasp Technologies’ option, with reasonable promptness after being notified. These provisions do not prolong the original warranty term for any product which has been repaired or replaced by Wasp Technologies.
デバイスWasp Bar Code WPL305の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wasp Bar Code WPL305をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWasp Bar Code WPL305の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wasp Bar Code WPL305の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wasp Bar Code WPL305で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wasp Bar Code WPL305を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWasp Bar Code WPL305の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wasp Bar Code WPL305に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWasp Bar Code WPL305デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。