WaspメーカーWLP 4170 CCDの使用説明書/サービス説明書
ページ先へ移動 of 40
Wasp WLP 4170 CCD Programming Guide Please Read Note: The W asp WLP 4170 CCD Scanner is ready to scan the most popular bar codes out of the box. This manual should only be used to make changes in the configuration of the scanner for specific applications.
© Copyright W asp T echnologies 2002. All rights reser v ed. V ersion 1.0 No part of this publication may be reproduced or transmitted in any for m or by any means without the written permission of W asp T echnologies . The information contained in this document is subject to change without notice .
T able of Contents Chapter 1. Introduction.............................................................................. 1 Chapter 2. Installation................................................................................ 2 Chapter 3. Quick Star t .
1 Chapter 1 Introduction Bar coding is the most common Automated Data Collection (ADC) technology providing timely, error-free information that can be used to increase productivity , accuracy, and efficiency in the workplace . Virtually ev ery type of industry is using bar codes to replace k eyboard data entr y .
2 1. T urn off your computer . 2. Unplug your PC k e yboard cable and plug the male end (Din 5) of the Wasp WLP 4170 CCD Scanner directly into your PC k e yboard port. Plug your k e yboard cable into the other end (female Din 5) of the the W asp WLP 4170 CCD Scanner.
3 Y our W asp WLP 4170 CCD Scanner is ready to go . The default settings of the W asp WLP 4170 CCD Scanner ha v e been pre-prog r ammed for the most common bar code configurations . Use the "Setup & Configuration" sections only to customize the Wasp settings.
4 Bar codes are symbols consisting of a series of bars and spaces which can be applied to packages, cartons, bottles, and other commercial products . The bars and spaces in each symbol are grouped in such a w a y to represent a specific ASCII character or function.
5 In order to configure W asp WLP 4170 CCD Scanner, you must familiariz e y ourself with the setup procedures on the following pages . The default settings of W asp WLP 4170 CCD Scanner are identified on each page and clearly mar k ed using an asterisk (*).
NOTE: Scanning these bar codes returns the scanner to the factory default settings 1. Scan “Begin ” 2. Scan “Default” to restore scanner to default settings 6 Tip: Use this configuration to restore the factory default settings if you are unsure how your scanner has been configured.
7 Setup & Configuration —Beep and Dela y Beep V olume Settings 00 None 01 Lowest 02 Low 03 Medium (Default) 04 Medium-High 05 High 06 High-Medium 07 Highest The 'Beep V olume' configuration changes the volume of the audible indicator of the WLP 4170 CCD Scanner .
8 Setup & Configuration —Interc haracter Dela y Inter character Delay Settings 00 Slo w est 01 Slo w 02 Default 50 Medium 75 F ast 99 F astest The 'Intercharacter Delay' configuration sets the speed at which the WLP 4170 CCD Scanner sends data.
9 Setup & Configuration —Ke yboard W edg e 00 K eyboard Present* 01 Laptop/No k e yboard The 'Ke yboard W edge' configuration supports options related to managing ke yboard operations . The 'Function Code' option enables/disables support for your ke yboard function k eys.
*Default 00 Default* 04 Continuous 10 Setup & Configuration —Scanning Modes Begin Set Scanning Mode Exit The 'Scanning Mode' option controls the trigger and LED settings for the WLP 4170 CCD Scanner. NOTE: For help in configuring these settings, consult the programming steps on pa ge 5.
Preamble Data P ostamble 11 Setup & Configuration —Preamble and Postamble *Default The 'Preamble' and 'Postamble' options are used to add prefix and suffix characters to the bar code value . Up to 22 characters may be added for each option separately .
12 Setup & Configuration —Code 39 Co de 39 i s v a ri a b le leng t h a n d i s th e most fr equ e n tly use d s ymb olog y in indus t r i a l ba r co d e sys tem s toda y and is e x t e n s i v el y use d wit hi n t he Dep ar tme nt o f D ef e n s e ( D O D ) .
13 Setup & Configuration —Code 39 (cont.) St andar d Co d e 3 9 co n t a i n s o nly 4 3 cha ra ct ers (0- 9 , A-Z , $, / , % , +, - , . , SP A C E ) a nd ca n b e e xtend ed to a 12 8 c ha r a .
14 (continued on next page) *Default Setup & Configuration —Code128 On/Off V erify Check Digit Begin T ransmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable 01* Disable 00* Enable 01 NOTE: For help in configuring these settings, consult the programming steps on pa g e 5.
15 Setup & Configuration —Code128 (cont.) Set Maximum Length Set Minimum Length Begin Format Exit Option Alpha/Numeric Entr y (Back Flap) 64 - Minimum 00 - 64 00* 64 - Maximum 00 - 64 00* Standard 00* UCC/EAN-128 01 NOTE: For help in configuring these settings, consult the programming steps on pa ge 5.
16 Setup & Configuration —UPC-A On/Off V erify Check Digit Begin T r ansmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable (two digits) 01* Disable 00 Enable 01* NOTE: For help in configuring these settings, consult the programming steps on pa g e 5.
17 Setup & Configuration —UPC-A (cont.) Begin Supplement Digits T r uncate Leading Zero Exit NOTE: For help in configuring these settings, consult the programming steps on pa ge 5. The first six digits of the UPC-A bar code are assigned from the Uniform Code Council (UCC).
18 (continued on next page) *Default Setup & Configuration —UPC-E On/Off V erify Check Digit Begin T ransmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable 01* Disable 00 Enable 01* NOTE: For help in configuring these settings, consult the programming steps on pa ge 5.
19 *Default Setup & Configuration —UPC-E (cont.) Supplement Digits T runcate Leading Zero Begin Expansion Exit NOTE: For help in configuring these settings, consult the programming steps on pa ge 5. The printed value of the UPC-E code is a twelve digit code .
20 (continued on next page) *Default Setup & Configuration —EAN-13 On/Off V erify Check Digit Begin T ransmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable 01* Disable 00 Enable 01* NOTE: For help in configuring these settings, consult the programming steps on pa ge 5.
21 Setup & Configuration —EAN-13 (cont.) NOTE: For help in configuring these settings, consult the programming steps on pa ge 5. The EAN/JAN-13 (European Article Number/Japanese Article Number) is fixed length and is similar to the UPC-A symbology, but encodes a 13th digit.
22 (continued on next page) *Default Setup & Configuration —EAN-8 On/Off V erify Check Digit Begin T ransmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable 01* Disable 00 Enable 01* NOTE: For help in configuring these settings, consult the programming steps on pa g e 5.
23 *Default Setup & Configuration —EAN-8 (cont.) Supplement Digits T r uncate Leading Zero Begin Expansion Exit Option Alpha/Numeric Entr y (Back Flap) None 00* 2 digits 01 5 digits 02 2 / 5 digits 03 or None Disable 00* Enable 01 Disable 00* Enable 01 NOTE: For help in configuring these settings, consult the programming steps on pa g e 5.
24 Setup & Configuration —Code 93 On/Off V erify Check Digit Begin T ransmit Check Digit Set Maximum Length Set Minimum Length Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00* Enable 01 .
25 Setup & Configuration —Interleaved 2 of 5 *Default Begin On/Off V erify Check Digit T ransmit Check Digit Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00 Enable 01* Disable 00* Enable 01 NOTE: For help in configuring these settings, consult the programming steps on pa g e 5.
26 Setup & Configuration —Codabar *Default On/Off V erify Check Digit Begin T ransmit Check Digit Set Maximum Length Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00 Enable 01* Disable 00* Enable 01 Disable 00* Enable 01 64 - minimum 64 - 00 00* NOTE: For help in configuring these settings, consult the programming steps on pa ge 5.
27 *Default Setup & Configuration —Codabar (cont.) Set Minimum Length Start/Stop T ype Begin Start/Stop T ransmission Exit Option Alpha/Numeric Entr y (Back Flap) 00 - Maximum 00 - 64 00* ABCD/A.
28 Setup & Configuration —MSI Plesse y On/Off V erify Check Digit Begin T ransmit Check Digit Set Maximum Length Set Minimum Length Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00* Enabl.
29 Setup & Configuration —PDF417 On/Off Begin Exit Option Alpha/Numeric Entr y (Back Flap) Disable 00* Enable 01 NOTE: For help in configuring these settings, consult the programming steps on pa g e 5. PDF417 is a 2D variable length symbology that can encode virtually any letter, number, or character .
30 Code 39* Interleav ed 2 of 5 Codabar* Code 128* MSI/Plesse y Code 93* Setup & Configuration —Bar Code T est Symbols—Appendix A Note: Make sure that the appropriate bar code symbology is configured properly and enabled before trying to scan.
31 UPC-A* UPC-E* UPC-E w/5 digit supplement UPC-E w/2 digit supplement UPC-A w/2 digit supplement UPC-A w/5 digit supplement Setup & Configuration —Bar Code T est Symbols—Appendix A (cont.
EAN/J AN 13* EAN/J AN 13 w/2 digit supplement EAN/J AN 13 w/5 digit supplement 3 Setup & Configuration —Bar Code T est Symbols—Appendix A (cont.
EAN/JAN 8* EAN/JAN 8+5 w/5 digit supplement EAN/JAN 8 w/2 digit supplement PDF417 33 Setup & Configuration —Bar Code T est Symbols—Appendix A (cont.
34 Setup & Configuration —WLP 4170 CCD Specifications MODEL WLP 4170 OPTICAL Scanning Width 3.2 in (120 mil) Depth of Field 0 to 3 in (0 to 200 mil) Scan Rate 200 scans / second ELECTRICAL Light Source 660 nm red visible LED Sensor 2,048 pixel CCD arr a y Operating V oltage +5 VDC ± 0.
35 W asp Bar Code products are warranted against defects in workmanship and materials for a period of one year from the date of shipment, provided that the product remains unmodified and is operated under normal and proper conditions.
43 C 44 D 45 E 46 F 47 G 48 H 49 I 4A J 4B K 4C L 4D M 4E N 4F O 50 P 51 Q 52 R 53 S 54 T 55 U 56 V 57 W 58 X 59 Y 5A Z 5B [ 5C 5D ] 5E ^ 5F _ 60 ` 61 a 62 b 23 # 24 $ 25 % 26 & 27 ‘ 28 ( 29 ) 2A ★ 2B + 2C 2D - 2E .
0 1 2 3 4 5 6 7 8 9 A B C D E F FINISH BACK COVER BAR CODES.
デバイスWasp WLP 4170 CCDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wasp WLP 4170 CCDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWasp WLP 4170 CCDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wasp WLP 4170 CCDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wasp WLP 4170 CCDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wasp WLP 4170 CCDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWasp WLP 4170 CCDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wasp WLP 4170 CCDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWasp WLP 4170 CCDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
