Watlow ElectricメーカーStyle Dの使用説明書/サービス説明書
ページ先へ移動 of 8
1241 Bundy Boulevard, Winona, Minnesota USA 55987 Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www .watlow .com Please consult this user’s manual when you place your new DIN-A-MITE in service. It contains all the necessary information to mount and wire it into the application.
Specifications 2 W A TLOW DIN-A-MITE S tyle D User ’s Manual Operator Interface • Command signal input and indication light • Alarm output and indication light Amperage • Single-phase, 80A output maximum at 50°C (122°F) into a resistive load.
DIN-A-MITE Style D , solid-st ate power controller Part Number D D 1 0 - __ __ __ __ - __ __ __ __ Phase 1 = Single-phase, one controlled leg Cooling and Current Rating 0 = Natural convection; current rating 80A @ 50°C (122°F) Note: See the output rating curve for the current rating at other temperatures.
4 W A TLOW DIN-A-MITE S tyle D User ’s Manual After removing all power , use a 7/16-inch nut driver to remove fuse mounting nuts. T orque to 4.52 Nm (40 in-lb). ç WARNINGS: Ó 1 WARNING: Use National Electric (NEC) or other country-specific standard wiring practices to install and operate the DIN-A-MITE.
W A TLOW DIN-A-MITE S tyle D User ’s Manual 5 Single-Phase Output and Input Wiring L1 2 1 Limit Control Contacts (if required) L1 for all voltages Alarm or Current Transformer Output Alarm or Current Transformer Output (Model Number-Dependent) Heater 4 to 20mA input: (+) (-) 4.
Declaration of Conformity DIN-A-MITE ® “D” Power Controller W atlow Winona, Inc. 1241 Bundy Blvd. Winona, MN 55987 USA Declares that the following product: Designation: DIN-A-MITE® “D” Power Control Model Numbers: DD10 – (02, 24, 48 or 60)(C0, C1, C2, K1, K2, K3, F0 or F1) – (0, C, D, H or S)(followed by any 3 numbers or letters.
W A TLOW DIN-A-MITE S tyle D User ’s Manual 7 An external EMI filter must be used in conjunction with the DIN-A-MITE for loads in excess of six amperes (6 A) at 150 to 250 kHz. Without a filter applied, the DIN-A-MITE does not comply with the conducted emissions standard for loads more than 6 A at 150 to 250 kHz.
The W atlow DIN-A-MITE is warranted to be free of defects in material and workmanship for 36 months after delivery to the first purchaser for use, providing that the units have not been misapplied. Since W atlow has no control over their use, and sometimes misuse, we cannot guarantee against failure.
デバイスWatlow Electric Style Dの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Watlow Electric Style Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWatlow Electric Style Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Watlow Electric Style Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Watlow Electric Style Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Watlow Electric Style Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWatlow Electric Style Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Watlow Electric Style Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWatlow Electric Style Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。