Wayne-Daltonメーカー9100/9400/9600の使用説明書/サービス説明書
ページ先へ移動 of 18
GARAGE DOORS & OPENERS Part No. IMPORT ANT NO TICES! Wayne-Dalton highly recommends that you read and fully under - stand the Installation Instructions and Owner’ s Manual before you attempt this installation. T o avoid possible injur y , read the enclosed instructions carefully before installing and operating the garage door .
2 Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com A.
I m p o r t a n t S a f e t y I n s t r u c t i o n s Definition of key words used in this manual: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS.
5/16” x 1 5/8” Hex head lag screws (as required) 1/4”-20 x 11/16” Self drilling screws (as required) 1/4”-14 x 5/8” Self tapping screws (as required) (2) #12 x 1/2” Phillips head screws .
and flush with the inside edge of the jamb. T emporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com section until it is seated against bottom section.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com T op Section T ools: Hammer , Step ladder , T ape measure 14 Place the top section in the opening.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Door Arm Hookup T ools: Needle nose pliers Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly , as shown.
Second section 1/8” Inside lock End cap (4) 1/4”-20 x 11/16” Self drilling screws Square hole in vertical track Pull Down Rope T ools: Power drill, 1/8” Drill bit, T ape measure W ARNING W ARNING DO NOT INST ALL PULL DOWN ROPE ON DOORS WITH OPERA TORS.
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE W ASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time.
Lifetime Limited Warranty Models 9100, 9400, 9600 Subject to the terms and conditions contained in this Lifetime Limited Warranty , Wayne-Dalton, A Division Of Overhead Door Corporation (“Manufactur.
.
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR THE GARAGE DOOR. Please Do Not Return This Product T o The Store Thank you for your pur chase. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pa ges business listings or go to the Find a Dealer section online at www .
デバイスWayne-Dalton 9100/9400/9600の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wayne-Dalton 9100/9400/9600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWayne-Dalton 9100/9400/9600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wayne-Dalton 9100/9400/9600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wayne-Dalton 9100/9400/9600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wayne-Dalton 9100/9400/9600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWayne-Dalton 9100/9400/9600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wayne-Dalton 9100/9400/9600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWayne-Dalton 9100/9400/9600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
