Wayne-DaltonメーカーWDSF-10の使用説明書/サービス説明書
ページ先へ移動 of 42
1 USB Z-W ave ® Adapter with Stand User Manual for Models WDUSB-10, WDUSB-10R, WDSF-10 Create, Manage and automate your Home Control System from your PC Thank you for purchasing the USB Z-Wave ® Adapter . Z-Wave ® products by Wayne-Dalton allow you to control your home by remote control.
2 T able of Contents T able of Contents Introduction ................................................................................................ 1 Package Contents ..................................................................................
3 Basics Copy – See Replicate. Delete – Erase transmitter or scene information from Controller . Also known as Exclude. Device – Any item that is connected to a module (for example, lamps). Exclude – Remove a module, transmitter or scene from the controller .
4 Basics The Wayne-Dalton USB Z-W ave ® Adapter with ThinkEssentials ® software allows you to use your PC to create, manage and automa te your Z-W ave ® home control system.
Basics Screen Layout Information 5 8 The number below corresponds to the bubble number above. 1. Minimize, Maximize and Close Buttons control W ayne-Dalton ThinkEssentials ® window . 2. Home T ab for a pplication operations and Settings T ab for global software settings.
6 T h i n k E s s e n t i a l s C D C D T R A Y Install USB Adapter and USB stand into computer USB port. Use this procedure to install the ThinkEssentials ® software on your Personal Computer . 1. Insert the ThinkEssentials ® CD into your Windows XP , Vista, or newer computer .
7 Z-Wave ® Network Setup Plug in lamp or appliance Use CHANGE LOCA TION link to set your physical location. Use the following procedure to setup your Z-Wave ® network with the W ayne-Dalton USB Z-Wave ® Adapter as your primary controller . Setting up your network refers to assigning Z-Wave ® modules to the USB Z-Wave ® Adapter’ s network.
8 1. From the Design tab, press the ADD DEVICE button. A message window will ask you to press the button on the device to add. 2. Press-and-release the PROGRAM button on the Z-Wave ® module. If successful, a message window will appear sta ting that the device has been successfully added.
9 3. The added Z-W ave ® module will appear as an icon in the lower right corner of the ThinkEssentials ® window . Y ou may move these icons around by clicking and dragging them into open spaces or into rooms (see Drawing a floor plan, page 11-12.) 4.
10 Module appears bright indicating it is in ON position. Module appears dim indicating it is in OFF position. Example of Dimming bar . Use the following procedures for controlling Z-Wave ® modules individually . For more adv anced control functions please see the section titled “Creating/ Modifying Schedules”, page 19-20.
11 Y ou may optionally dra w a basic floor plan or room layout in the software for organizing your Z-Wave ® modules. 1. T o dra w a room, c lick the DRAW ROOMS button in the Design pane. This will enable DRAW ROOMS mode. T o exit this mode, c lick the DRAW ROOMS button again.
12 Click on ERASE to enter or leave Erase drawing mode. Example showing sections erased. Example showing upstairs erased. Press-and-Hold left mouse button or right click to get the options to RENAME ROOM or REMOVE ROOM. T o erase a room or rooms, or parts of a room or rooms, c lick the ERASE button in the Design pane.
Remov ing Modul es fro m Net work 13 Use the following procedure to remove Z-Wave ® modules from your Z-Wave ® network. 1. From the Design tab, press the REMOVE DEVICE button. A message window will ask you to press the button on the device to remove.
Remove/ Replac e Broken Modul es Use the following procedure to remove or replace a module has been physically removed from the premises without being removed from the network or is broken. A broken module is indicated by a red circle with a slash over the module.
Locking/Unlocking ThinkEssentials ® 15 LOCKED/UNLOCKED link is located in lower left hand corner of ThinkEssentials ® window . Use the following procedure to lock/unlock ThinkEssentials ®. ThinkEssentials ® software operates in two modes: a) locked and, b) unlocked.
16 Scenes/Zones Creating Scenes and Zones ThinkEssentials ® makes it easy to set up scenes and zones. These two features are similar but are uniquely powerful. Scenes activate a certain set of modules together , with each module changing to its own preset level.
Creating Scenes/Zones 17 Use the following procedure to create or add Scenes and Zones in ThinkEssentials ® . T o add a scene or zone: 1. Go to the Scene or Zone tab, then Click the ADD SCENE or ADD ZONE button, respectively . This button is found at the bottom of the list of scenes or zones.
Modif y ing Sce nes/ Zon es Use the following procedure to modify existing Scenes and Zones in ThinkEssentials ® . T o modify a scene or zone: 1. Press-and-hold the left mouse button or right-click the button for the scene or zone you wish to modify .
Schedules 19 One of the most powerful features of ThinkEssentials ® is the ability to create schedules. ThinkEssentials ® can help you save energy , make life more convenient, or increase the security of your home by automatically activating scenes or zones a t certain times of the day or at sunrise or sunset.
Crea ting /Mod if ying Sc hedule s (contin ued) 5. Click on the days of week when the schedule item should occur . 6. Click on the time pull-down near the right to change the time of day when the schedule item should occur . Y ou may also choose sunrise or sunset.
Viewing/Modifying Schedules 21 Use the following procedure to view or modify schedules in ThinkEssentials ®. T o view or modify all schedules: 1. Switch to the SETTINGS tab. 2. Click the VIEW ALL SCHEDULES link. Modify the desired fields per instructions in the section “Creating/Modifying Schedules”, pages 19-20.
Joini ng Think Ess enti als ® t o Ex ist ing Net wor ks 22 Network Operations Use the following procedure to join an existing network or add ThinkEssentials ® as another controller (secondary) to the network. T o join ThinkEssentials ® to an existing Z-Wave ® network as a secondary controller: 1.
Receiving Network Updates 23 Network Operations Select RECEIVE UPDA TE FROM PRIMARY CONTROLLER. Initiate Primar y Controller to SEND REPLICA TION. Use the following procedure to update network informa- tion in ThinkEssentials ® when ThinkEssentials ® is a secondary controller .
Adding a C ontr oller to th e net work Use the following procedure to add secondary controllers to a network where ThinkEssentials ® is the primary controller .
Removing Controllers from the network 25 Use the following procedure to remove secondar y controllers from a network where ThinkEssentials ® is the primary controller .
Updating Secondary Controllers 26 Use the following procedure to update secondary controllers in a network where ThinkEssentials ® is the pri- mary controller . It is best practice to update the network information in your secondar y controllers whenever Z-Wave ® modules are added or deleted from the network by the primary controller .
27 Optimize/Repair Network Over time, you may notice the software response slowing down or there may be communication failures in your Z-Wave ® network indicated by the red circle slash.
28 Use the following procedure to transfer the Primary Controller role from ThinkEssentials ® to another controller . T ransferring the primary controller role between controllers is sometimes necessary or convenient when working with your Z-Wave ® network.
29 Use the following procedure to transfer the Primary Controller role from another controller to ThinkEssentials ® . T ransferring the primary controller role between controllers is sometimes necessary or convenient when working with your Z-Wave ® network.
30 Backup Network Settings Use the following procedure to backup your ThinkEssentials ® configuration to the drive and directory of your choice. The Wayne-Dalton USB Z-W ave ® adapter stores basic i.
31 Restore Network Settings Use the following procedure to restore your ThinkEssentials ® configuration to the drive and directory of your choice. The Wayne-Dalton USB Z-W ave ® adapter stores basic.
32 Use the following procedure to set a specific and custom latitude and longitude. Wayne-Dalton ThinkEssentials ® allows for setting a custom latitude and longitude by using a command line configuration option. The custom latitude and longitude will remain programmed each time ThinkEssentials ® is started until it is changed.
33 Use the following procedure to add a command line option to your ThinkEssentials ® shortcut. Command line options (other than latitude and longitude) used with ThinkEssentials ® must be initiated each time ThinkEssentials ® is started.
34 Use the following procedure to run more than one instance of ThinkEssentials ® . Multiple instances of ThinkEssentials ® may be run on one computer simultaneously .
35 Use the following procedure to set the poll rate in ThinkEssentials ® by the number of seconds. Y ou can temporarily establish a specific poll rate in ThinkEssentials ® using seconds as the unit.
36 Use the following shortcut to poll the Z-Wave ® modules one time to refresh the ThinkEssentials ® screen. Press the F5 key on the keyboard to refresh and poll the Z-Wave ® modules in the network. Refresh Shortcut Shortcuts Press F5 to refresh and poll the network.
Use the following procedure to exit and completely shut down and close the ThinkEssentials ® program. ThinkEssentials ® will run in the background if schedules are programmed and will not completely shut down when the X (CLOSE button located in the upper right corner) on the window is pressed.
38 Resetting Thinkessentials ® Use the following procedure to reset your USB Z-Wave ® Adapter to f actory conditions. WARNING: If your USB Z-W ave ® Adapter and ThinkEssentials® software are the P.
39 T roubleshooting T roubleshooting Problem: • I cannot add or remove modules to or from my network. The ADD DEVICE and REMOVE DEVICE buttons are faded out (dimmed). Problem: • I cannot add or remove a module to or from my network. I press the PROGRAM button on the module but the software never responds.
T roubleshooting Problem: • I am setting up a scene, but the software will not let me add a particular module to the scene. Problem: • I have set up a schedule for a zone or scene, but the schedule is not being activated on time or is not being activated at all.
41 T roubleshooting T roubleshooting Problem: • I joined a network instead of adding another controller to my network. Now , neither the software nor the controller can control anything. Problem: • I cannot control a module in my network, or am experiencing intermittent module failures or sluggishness controlling my modules.
FCC and IC Statement FCC Regulatory Information: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
デバイスWayne-Dalton WDSF-10の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wayne-Dalton WDSF-10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWayne-Dalton WDSF-10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wayne-Dalton WDSF-10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wayne-Dalton WDSF-10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wayne-Dalton WDSF-10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWayne-Dalton WDSF-10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wayne-Dalton WDSF-10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWayne-Dalton WDSF-10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
