WesloメーカーWLSY71500の使用説明書/サービス説明書
ページ先へ移動 of 24
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are missing or damaged parts, we will guarantee you complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 WG7150 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 75 1/2 in. Width: 55 3/4 in. Length: 72 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Arms Weight Stack Backrest Weight Pin Thank you for selecting the versatile WESLO ® BODY FLEX Weight System.
4 ASSEMBL Y 1 2 88 8 3 4 82 Bracket Low Side 3 8 14 88 5 11 86 3 8 2 11 Slot Slot 8 11 3 20 4 1 27 Assembly requires two people. Due to the size and weight of the weight system, assemble it in the loca- tion where it will be used.
5 3. Press the 1 1/4” Inner Cap (57) into the Front Upright (42). Attach the 1” Plastic Stop (64) to the center hole in the Stop Bracket (63) with a 5/16” x 1 1/2” Bolt (24) and 5/16” Jam Nut (2).
6 6. Press the Weight T ube Bumper (79) into the indi- cated end of the Weight T ube (80). Insert the Weight T ube (80) into the stack of Weights (25). Slide the eighth Weight (25) onto the upper end of the Weight T ube. The Weight T ube must be turned so the welded pin is in the pin groove in the Weight.
7 9. Press two 1 3/4” Inner Caps (44) into each of the Arms (46). Apply lubricant to the lower axles on the Arm Frame (52). Slide a Plastic Bushing (53) and an Arm (46) onto one of the axles. The upper end of the Arm must be between the Front Upright (42) and the bracket on the Arm Frame (52).
8 12. Attach a Large “U” Bracket (56) to one of the Arms (46) with a 3/8” x 2 1/2” Bolt (62), 3/8” Flat W asher (9) and 3/8” Nylon Lock Nut (21). Lubricate a 5/16” x 2” Bolt (61). Attach a Narrow Swivel Bracket (58) to the Large “U” Bracket (56) with the Bolt and a 5/16” Jam Nut (2).
9 12 3 6 9 10 12 3 6 9 16. Insert the end of the Long Cable (66) through the indicated bracket on the T op Frame (67), and down through the indicated hole in the T op Frame. Hold a 3 1/2” Pulley (15) inside the bracket on the T op Frame (67). The Long Cable (66) must be between the Pulley and the top of the bracket.
10 12 3 6 9 12 3 6 9 20 Wrap the Long Cable (66) up around a 3 1/2” Pulley (15). Attach the Pulley and a Cable T rap (59) to the Narrow Swivel Bracket (58) on the right Arm (46) with a 3/8” x 1 3/4” Bolt (12) and 3/8” Jam Nut (6). The Cable Trap must be turned to the “3 o’clock” position.
11 23. Attach the Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and 1/4” Flat W ashers (10). 24. Press a 1 1/2” Inner Cap (32) into the Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) into the center of each Seat Plate (37).
12 27. Wet the ends of the Lat Bar and insides of the two remaining Handgrips (48) with soapy water . Slide the Handgrips onto the ends of the Lat Bar . 27 85 48 48 29. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in ADJUST- MENT , beginning on page 13 of this owner's manual.
13 ADJUSTMENT The instructions below describe how each part of the weight system can be adjusted. Refer to the EXERCISE GUIDE accompanying this owner's manual to see how the weight system should be set up for each exercise.
14 A TT ACHING THE LEG LEVER TO THE LOW PULLEY ST A TION T o use the Leg Lever (29), the seat must be attached to the front upright (see A TT ACHING AND REMOV- ING THE SEA T on page 13). Attach the Chain (84) between the Short Cable (23) and the 5/16” x 2” Eyebolt (35) on the Leg Lever with two Cable Clips (83).
15 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
16 Key No. Qty . Description 1 2 5/16” x 2 1/2” Carriage Bolt 2 6 5/16” Jam Nut 3 23 5/16” Nylon Lock Nut 4 1 Base 5 1 Stabilizer 6 6 3/8” Jam Nut 7 6 1/4” Nylon Lock Nut 8 21 5/16” Flat.
17 EXPLODED DRA WING—Model No. WLSY71500 R0897A 3 77 77 78 78 21 82 88 5 4 19 11 8 1 6 20 3 27 15 59 12 34 34 50 32 8 3 31 50 34 29 35 3 33 7 30 10 7 28 34 32 36 39 13 38 37 18 40 14 23 87 8 22 16 1.
18 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (66). Use the diagram to make sure that the two cables are assembled correctly . The letters show the routing of the Short Cable (23); the numbers show the routing of the Long Cable (66).
19.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
This chart is provided to help identify the small parts used in assembly . Some parts come pre-assembled for shipping purposes; if a part cannot be found in the parts bags, check the system frame to make sure it hasn’t come pre-assembled. The number in parenthesis below each part refers to the key number of the part.
1" Round Cap (49)–7 1" Cover Cap (55)–2 3/4" Inner Cap (34)–4 1 1/4" Inner Cap (57)—1 1 1/2" Inner Cap (32)—2 1 3/4" Inner Cap (44)–6 2" Inner Cap (27).
5/16" Nylon Lock Nut (3)–23 1/4" Flat W asher (10)–4 5/16" Flat W asher (8)–21 3/8" Flat W asher (9)–5 3/8" Jam Nut (6)–6 5/16" Jam Nut (2)–8 1/4" x 2 1/.
1/2" x 3/8" Spacer (51)—2 5/16" x 2" Bolt (61)–1 5/16" x 2 3/4" Bolt (1 1)–10 1" Retainer (54)–4 5/16" x 3" Bolt (17)–2 5/16" x 1 1/2" .
デバイスWeslo WLSY71500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weslo WLSY71500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeslo WLSY71500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weslo WLSY71500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weslo WLSY71500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weslo WLSY71500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeslo WLSY71500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weslo WLSY71500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeslo WLSY71500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。