WhirlpoolメーカーSystem Iの使用説明書/サービス説明書
ページ先へ移動 of 14
m 1 InstructionS WHIRLPOOL UNDERCOUNTER WATER FILTRATION SYSTEMS I, II, & Ill.
Remove parts from packages. Check that you have all the parts. filtration assembly System I (A) filtration assembly System II (B) filtration assembly System III (C) filtration assembly cover (D) 2 mou.
Before You Start . . . IMPORTANT: Read and save these instructions. If you need assistance.. . It is recommended that this system be installed by a licensed plumber.
Instructions At A Glance l For detailed instructions see following page. 1. Turn off cold water supply. (St; la-lb) Electrical Shock Hazard Special care must be taken when drilling into water pipes.
Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. la Take note of water requirements listed under . the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve.
Instructions At A Glance l For detailed instructions see following page. 1. Decide if the system will be connected to your refrrgerator, to an optional faucet or to both. (Step 2a) 3. Or, insta!l faucet in sink and connect blue tubing to filtration assembly.
2a You have three installation options: . 1 .Connect water supply from filtration system to refrigerator’s ice and water only. 2.Connect water supply from filtration system to optional sink faucet only. 3.Connect water supply from filtration system to both refrigerator and optional sink faucet.
Start Up Instructions At A Glance l For detailed instructions see following page. i . I 1. Slide filtration assembly onto mounting screws. (Steps 3a-3c) 2. Turn on cold water supply. (Step 3d) 3. If filtration assembly was connected to refrigerator, make and discard 2 batches of ice and drain 2-3 gallons of water from water dispenser.
Start Up Electrical Shock Hazard Special care must be taken when drilling into walls. Electrical wires may be concealed behind the wall covering: - Use only an electric drill with a 3-wire power supply cord connected to a grounded receptacle.
Water Requirements The filtration system must be connected to a cold water supply line providing 30-l 00 psi water pressure. The water temperature must be between 40”-100°F.
Call l-800-253-1301 to order. Replacement Parts & Accessories System I Replacement Cartridge Kit Kit includes Sediment/Carbon (SC) Cartridge 4373529 System II Replacement Cartridges Kii Kit includes Lead Reduction (L) and Carbon Filter (CF) Cartridges.
Performance Data Sheet 0 NSF This product has been tested and listed by NSF International under B Standard 42 for Taste, Odor and Chlorine reduction (Class I) and This product has been tested and listed by NSF International under Standard 42 Particulate reduction (Class II).
Performance Data Sheet This product has been tested and listed by NSF International under Standard 42 for Taste, Odor and Chlorine reduction (Class I) and Particulate reduction (Class II) and under Standard 53 for Cyst, Turbidity, Lead and VOC reduction.
Part No. 4373576 01993 Whirlpool Corporation - Whirlpool Corporation Benton Harbor. Ml 49022 CB Printed on Recycled Paper in U.S.A..
デバイスWhirlpool System Iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Whirlpool System Iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhirlpool System Iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Whirlpool System Iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Whirlpool System Iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Whirlpool System Iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhirlpool System Iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Whirlpool System Iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhirlpool System Iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
