WhirlpoolメーカーW10038100の使用説明書/サービス説明書
ページ先へ移動 of 8
W ASHER INSTA LLATION INSTRUCTIONS W A SHER SAFETY W10038 100 T able of Contents WASHER SAFETY ............... .............. ............... 1 INSTALLATION REQUIREMENTS ................ . 2 Tools and Parts ................ .............. ............
2 INST ALLA TION REQUIREMENTS To o l s a n d P a r t s Gather the required tools and parts before startin g installation. The parts supplied ar e in the washer basket.
3 Recessed a rea or closet installatio n The dimensions sh own are for the r ecommended spacing allow ed (A and B), except the closet door ventilation openings. The dimen sio ns sh own fo r th e c loset do or vent ila tion op ening s (C ) are the minimu m required.
4 ■ T o minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accord ance with local codes an d ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly earthed outlet installed by a qualified electrician.
5 2. Firmly grasp th e power cord and pull to completely remove the power cord, cor d r estraint, and pin from the rear panel. 3. Confirm that the power c ord r estraint (A), and pin (B) ar e rem o ve d . 4. T o remove the power cor d from the cord r estraint, push the power cord in, press T AB, and then pull the power co rd out.
6 ■ Then slide the second hose clamp onto coupling. Insert end of adapter into coupling. Use a screwdriver to install second hose clamp over coupling. T o keep dra in water from going bac k into the wash er: ■ Do not for ce exce ss drain hose into stan dpipe.
7 NOTE: Do not overtighten or use tape or sealants on the valve. Damage to th e valves can result. 5. Attach the cold water hose to the top inle t valve. 6. Screw on couplin g by hand until it is seated on the washer . 7. Using pliers, tighten th e couplings with an additional two-thi rds turn.
2. Tilt the washer forward until the rear of th e washer is at least 10.2 cm (4") off the floor . Y ou ma y hear the self-a djusting rear feet click into place. Lower the washer to the floo r . 3. Check the levelness of the washer by placing a level on the top edges of the washer , fi rst side to side, then front to back.
デバイスWhirlpool W10038100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Whirlpool W10038100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhirlpool W10038100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Whirlpool W10038100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Whirlpool W10038100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Whirlpool W10038100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhirlpool W10038100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Whirlpool W10038100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhirlpool W10038100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。