WhirlpoolメーカーW10255468Cの使用説明書/サービス説明書
ページ先へ移動 of 16
ELECTRIC DRYER INSTALLATION INSTRUCTIONS U.S.A. ONL Y Para una versión de estas instruccione s en español, visite www .Whirlpool.com T ABLE OF CONTENTS DRYER SAFETY........... ............................ ................................... .... 1 INSTALLATION REQUIREMENTS .
2 INST ALLA TION REQUIREMENTS To o l s a n d Parts G ather the r e quired tools and parts be fore starting installation. Read and follow the instructions provid ed with any tools listed here.
3 Optional Equipment Refer to your Use and Care guide for information about the accessories avail able for your dryer . Location Requirements Y ou will nee d ■ A location that allows for proper exhaust instal lation. See “V enting Requirements.” ■ A separate 30-amp circuit.
B C A* 4 Side View Steam (Electric or Gas) Non-Steam (Electric or Gas) A* 1" (2 5 mm) 1" (25 mm) B 7 5 / 8 " (194 mm) 7 5 / 8 " (194 mm) C 3 3 / 8 " (86 mm) 3 3 / 8 " (86 mm) * Dimension A is appr oximate, depending on when the diamond marking on the leveling foot is no longe r visible.
5 Recommen d e d installation spacing for ca b inet installation NOTE: Some models are not r ecommen ded for cabinet installation. ■ For cabinet installation, with a door , minimum ventilation openings in the top of the cabinet are r equired.
6 ■ T o supply the requir ed 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only elec trical supply (or 3 or 4 wire, 120/208 volt e lectrical supply , if specified on the serial/rating p late) on a separate 30-amp circuit, fused on both sides of the lin e.
7 2. Remove the hol d-down scre w and terminal block cover . A. Neutral g round wire B. External ground conductor screw C. Center , silver -colored terminal block screw D.
8 ■ Put direct wire cable through the strain relief. Th e strain relief should have a tight fit with the dryer cabinet and be in a horizontal position.
9 3. Connect ground wir e (green or bare) of power supply cord to external ground conductor scr ew . Tighten screw . A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. ¾" (19 mm) UL listed strain relief D. Center , silver -colored terminal block screw E.
10 5. Tighten strain relief scr ew . 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down scr ew . 7. Y ou have completed your electrical connection.
11 4. Tighten strain relief scr ew . 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down scr ew . 6. Y ou have completed your electrical connection.
12 Flexi b le metal vent ■ Flexible metal vents are acceptable only if accessible for cleaning. ■ Flexible metal vent must be fully exte nded and supported when the dryer is in its final location. ■ Remove excess flexible meta l vent to avoid sagging and kinking that may result in re duced airflow and poor performance.
A B C A. Standard rear offset exhaust in stallation B. Left or right si de exhaust installation C. Bottom exhaust installati on 13 Alter nate installat ions for close clearances V enting systems come in many variet ies. Select the type best for your installation.
14 2. Firmly grasp the body of the dryer (not the console panel). G ently lay the dryer on the cardboar d. See illustration. 3. Examine the leveling legs. Find the diamond marking . 4. Screw the legs into the leg holes by hand. Use a wren ch to finish turning the legs until the diamond marking is no longer visible.
15 LEVEL DRYER Check the levelness of the dryer . Ch eck levelness first side to side, then front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wren ch to adjust the legs up or down and check a gain for levelnes s. COMPLETE INSTALLATION 1.
T ry th e following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit br eaker . Confirm the power cord is pr operly installed. Refer to “Electrical Conn ection” for details.
デバイスWhirlpool W10255468Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Whirlpool W10255468Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhirlpool W10255468Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Whirlpool W10255468Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Whirlpool W10255468Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Whirlpool W10255468Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhirlpool W10255468Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Whirlpool W10255468Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhirlpool W10255468Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。