WhirlpoolメーカーW10459123Bの使用説明書/サービス説明書
ページ先へ移動 of 16
INSTALLATION INSTR UCTIONS 20" (50.8 CM) FREESTANDING G AS RANGE with Standard Clean Ov en T able of Conten ts RANGE SAFETY ................................. ......................................... ... 2 INSTALLATION RE QUIREMENTS .............
2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
3 In the State of Massachusetts, the following installation instructions apply: ■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. ■ If using a ball valve, it shall be a T-handle type.
4 INST ALLA TION REQUIR EMENTS T ools and P ar ts Gather the req uired tools and part s befor e starting installation. Read and follow the instructions provided with any tools list ed here. T ools needed Parts supplied Check that all parts are included.
5 Product Dimensions Freesta nding Range Cabinet Dimensions Cabinet opening dimensions shown a re for 25" (64.0 cm) countertop depth, 24" (61.0 c m) base cabinet depth and 36" (91.4 cm) countertop height. If the cabinet depth is greater than 24" (61.
6 Electr ical Requirements IMPORT ANT : The range must be electric ally grounded in accordance with local codes and ordinances, or in the abse nce of local codes, with the Nationa l Electrical Code , ANSI/NFP A 70, latest edition.
7 Flexible metal appliance connector: ■ If local codes permit, a new CSA design-certified, 4-5 ft (122-152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D., flexible metal appliance connect or may be used for connecting range to the gas supply line.
8 INSTALLATION INSTR UCTIONS Unpack Range 1. Do not use oven door handle to lift or move the range 2. Remove shipping materials, tape and film from ran ge. Keep cardboar d bottom under r ange. 3. Remove oven racks and parts package fr om inside oven. 4.
9 Mak e Gas Connection T ypical rigid pipe connection A combination of pipe fittings mu st be used to connect the range to the existing gas line. Y our connections may be differ ent, according to the supply line type, size and locati on. 1. Apply pipe-joint compound made for use with LP gas to all pipe thread connections.
10 5. Close the broiler door . 6. Remove cooktop burner caps and grates from parts package. Align notches in bur ner caps with pins in bur ner base. Burner caps should be le vel when properly positioned. If burn er caps are not pr operly positioned, surfa ce burners will not light.
11 Check Operation of Cooktop Bur ners 1. If control panel and knobs were removed earlier , re install knobs. 2. Push in and turn eac h surface unit control knob to the “LITE” position. The flame should light within 4 seconds. 3. T ur n control knob to the “HI” position after burner lights.
12 7. Tighten the shutter screw . 8. Reinstall flame spreader and oven tray . Reinstall the oven racks. 9. Close the oven door . 10. Close the broiler door . Complete Installation 1. Check that all parts are now insta lled. If the re is an extra part, go back through the steps to se e which step was skipped.
13 3. Open broiler door and remove broiler pan. The gas pr essure regulator is located in the back right hand corner of the br oiler compartment. IMPORT ANT : Do not remove the gas pr essure r egulator . 4. Remove the cap fr om the gas pressur e regulator using a flat-blade screwdriver .
14 T o Convert Oven Burner 1. Open the oven d oor and r emove oven racks, oven tray and flame spre ader and set aside. 2. Lift oven burner . The orifi ce sp ud is behind the oven burner air shutter . 3. Locate LP gas orifice spud stamped “58” in the package containing literature supplied with the range.
15 4. Remove the cap fr om the gas pressur e regulator using a flat-blade screwdriver . NOTE: Do not remove the s pring beneath the cap. 5. T ur n the cap over so that N or NA T is visible. 6. Reinstall the cap. T o Convert Surface Burners 1. Remove bur ner grate, bur ner caps and bur ners.
T o Convert Oven Burner 1. Open the oven d oor and r emove oven racks, oven tray , and flame spre ader and set aside. 2. Lift oven burner . The orifi ce sp ud is behind the oven burner air shutter . 3. Locate Natural gas orifice spud stamped “51” in the package containing literature supplied with the range.
デバイスWhirlpool W10459123Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Whirlpool W10459123Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhirlpool W10459123Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Whirlpool W10459123Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Whirlpool W10459123Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Whirlpool W10459123Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhirlpool W10459123Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Whirlpool W10459123Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhirlpool W10459123Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。